DESIGN OF MACHINERY (LL) >C<
6th Edition
ISBN: 9781264001330
Author: Norton
Publisher: MCGRAW-HILL LEARNING SOLN.(CC)
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 4, Problem 4.28P
To determine
To Design: The maximum angular displacement possible for the rocker-crank linkage in the treadle link shown in the figure below.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Draw the kinematic diagram of the following mechanism by labelling the links and the
joints and calculate its mobility / DOF.
The following figure shows a treadle-operated grinding wheel driven by a four-bar linkage.Find the maximum and minimum transmission angles over its range of motion.
Problem 4-6a
The link lengths (a, b, c, d) and the value of 62 for a crank-rocker linkage are defined as
2, 7, 9, 6, 30°, respectively. Draw the scaled linkage. Find all possible solutions (both
open and crossed) for angles 03 and 04 graphically.
Open
B
3
A
LNCS
4
04
GCS
O4
Crossed
(This is not the scaled kinematic diagram.)
Problem 4-7a
Repeat Problem 4-6a except solve by the vector loop method.
Chapter 4 Solutions
DESIGN OF MACHINERY (LL) >C<
Ch. 4 - A position vector is defined as having a length...Ch. 4 - A particle is traveling along an arc of 6.5-in...Ch. 4 - Repeat problem 4-2 considering points A and B to...Ch. 4 - Repeat Problem 4-2 with the particles path defined...Ch. 4 - Repeat Problem 4-3 with the path of the particle...Ch. 4 - The link lengths and the value of 2 for some...Ch. 4 - Repeat Problem 4-6 except solve by the vector loop...Ch. 4 - Expand equation 4.7b and prove that it reduces to...Ch. 4 - The link lengths and the value of 2 and offset for...Ch. 4 - Repeat Problem 4-9 except solve by the vector loop...
Ch. 4 - The link lengths and the value of 2 and for some...Ch. 4 - Repeat Problem 4-11 except solve by the vector...Ch. 4 - Find the transmission angles of the linkages in...Ch. 4 - Find the minimum and maximum values of the...Ch. 4 - Find the input angles corresponding to the toggle...Ch. 4 - The link lengths. gear ratio (). phase angle (),...Ch. 4 - Repeat Problem 4-16 except solve by the vector...Ch. 4 - Figure P4-5 shows the mechanisms for the following...Ch. 4 - For one revolution of driving link 2 of the...Ch. 4 - Figure P4-7 shows a power hacksaw, used to cut...Ch. 4 - For the linkage in Figure P4-8, find its limit...Ch. 4 - For the walking-beam mechanism of Figure P4-9,...Ch. 4 - For the linkage in Figure P4-10, calculate and...Ch. 4 - For the linkage in Figure P4-11, calculate and...Ch. 4 - For the linkage in Figure P4-12, find its limit...Ch. 4 - Prob. 4.26PCh. 4 - For the linkage in Figure P4-13, find its limit...Ch. 4 - Prob. 4.28PCh. 4 - For the linkage in Figure P4-15, find its limit...Ch. 4 - For the linkage in Figure P4-15, find its limit...Ch. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - Figure 4-22 plots the cubic function from equation...Ch. 4 - Write a computer program or use an equation solver...Ch. 4 - Prob. 4.35PCh. 4 - Prob. 4.36PCh. 4 - Write a computer program or use an equation solver...Ch. 4 - Write a computer program or use an equation solver...Ch. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Write a computer program or use an equation solver...Ch. 4 - Prob. 4.42PCh. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Model the linkage shown in Figure 3-37a in...Ch. 4 - Prob. 4.46PCh. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Prob. 4.49PCh. 4 - Prob. 4.50PCh. 4 - Figure 3-29g shows Evans approximate straight-line...Ch. 4 - For the linkage in Figure P4-16, what are the...Ch. 4 - The coordinates of the point P1 on link 4 in...Ch. 4 - Write a computer program or use an equation solver...Ch. 4 - For the linkage in Figure P4-17, calculate the...Ch. 4 - Prob. 4.56PCh. 4 - Prob. 4.57PCh. 4 - The elliptical trammel in Figure P4-18 must be...Ch. 4 - Prob. 4.59PCh. 4 - Prob. 4.60PCh. 4 - Repeat Problem 4-60 except solve by the vector...Ch. 4 - Write a computer program or use an equation solver...Ch. 4 - Write a computer program or use an equation solver...Ch. 4 - Write a computer program or use an equation solver...Ch. 4 - Write a computer program or use an equation solver...Ch. 4 - Figure P4-20 shows a cut-away view of a mechanism...Ch. 4 - For the linkage in Figure 3-32a, calculate and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The linkage in Figure P7-5b has 04A = O2A = 0.75 , AB = 1.5 , and AC = 1.2 in . The effective crank angle in the position shown is 77º and angle BAC = 30 ° . Find a3 , AA , AB , Ac for the position shown for m2 = 15 rad / sec and a2 = 10 rad / sec2 in the directions shown using an analytical method . ( Hint : Create an effective linkage for the position shown and analyze it as a pin - jointed fourbar . ) the linkage has a parallelogram form Assume rolling contact C 02 A 3 . B 02 02 Tarrow_forwardCrank Rocker mechanism, Link 1= 177.8 mm; Link 2 = 228.6 mm; Link 3 = 76.2 mm and Link 4 = 203.2 mm. If the angular position of Link 2 is 85.22° find the possible angular positions of Link 3 and Link 4 using graphical method.arrow_forwardStudy the double slider crank mechanism in figure A: (a) Using Aronhold Kennedy Theory formula, find the number of Instantaneous Centers (b) Using a tabular method, list all instantaneous centers (c) Base on the figure A, locate all the instantaneous centers. (Use solidworks to show the solution or a drawing solution.)arrow_forward
- You are given a set of three links with lengths 2.4 in, 7.2 in, and 3.4 in. Select the length of a fourth link and assemble a linkage that can be driven by a continuous-rotation motor. Is your linkage a Grashof class I or nonGrashof class2 linkage? (Show your work.) Is it a crank-rocker, double- rocker, or double-crank linkage? Why?arrow_forwardProblem 4-6a The link lengths (a, b, c, d) and the value of 2 for a crank-rocker linkage are defined as 2, 7, 9, 6, 30°, respectively. Draw the scaled linkage. Find all possible solutions (both open and crossed) for angles 03 and 04 graphically. Орen B A LNCS 4 a GCS र 4 4" Crossed (This is not the scaled kinematic diagram.) Problem 4-7a Repeat Problem 4-6a except solve by the vector loop method.arrow_forwardA offset crank-slider mechanism is used in a conveyor loading device. Find the crank length in mm required to generate this motion. Use the design parameters specified below. (Note: A is the crank pivot; C is the coupler-slider joint; B is the coupler-crank joint). - CBDC: 107 mm below and 140 mm to right of A (Note: BDC=Bottom-Dead-Center) - Stroke: 52 mm along a 42° incline (This direction: /. Not this direction: \)arrow_forward
- Problem 2 The linkage in Figure P7-5b has O,A = O2A = 0.75, AB= 1.5, and AC = 1.2 in. The effective crank angle in the position shown is 77° and angle BAC = 30°. Find a3, A4, AB,Ac for the position shown for @2 = 15 rad/sec and a2 = 10 rad/sec in the directions shown using an analytical method. (Hint: Create an effective linkage for the position shown and analyze it as a pin-jointed fourbar.)the linkage has a parallelogram form Assume rolling contact C @2 A 3 В a2 2 4 04arrow_forwardProblem 4-15h Find the input angles (02) corresponding to the toggle positions of a non-Grashof double- rocker linkage with link lengths (a, b, c, d) of 10, 10, 10, 20, respectively.arrow_forwardThe following figure shows a treadle-operated grinding wheel driven by a four-bar linkage. Find the toggle and limit positions.arrow_forward
- Figure Q2-2 shows a schematic of a retractable landing gear of aircraft. The retraction mechanism is a 4 bar linkage (O1ABO2), which is actuated by a hydraulic cylinder and piston, D, pivoted at E with a joint at C to link O,A. Hydraulic cylinder & piston D Joint for landing gear wheel Figure Q2-2 Use the Gruebler's equation of DoF (Degrees of Freedom) of a linkage mechanism to assess if the landing gear produces the required retraction motion. 0,02 may be considered as the ground link. i) Hint: The joint of the wheel is not part of the linkage mechanism. The number of DoF may be used to check if it is a linkage with certain motions or a fixed structure. ii) The dimensions of the 4 bar linkage (O1ABO2) are measured as O102 = 800 mm, O1A = 780 mm, AB = 200 mm and O2B = 400 mm. Use Grashof condition to determine the specific type of this linkage. You may find the Gruebler's equation useful: M = 3(L – 1) – 2J where, M is degree of freedom (DoF) L is number of links J is number of jointsarrow_forwardPlates: Wiper blade 16" Wiper arm 70° 13" 3.5 Crank 14" Plate 1: Phase Position Analysis Graphically position the links for the rear-wiper mechanism shown above. Then reposition the links as the 2-in. crank is rotated 50° clockwise. Determine the resulting angular displacement of the wiper arm and the linear displacement at the end of the wiper blade. Plate 2: Limiting Position Graphically position the links for the windshield wiper mechanism shown above into the configurations that place the wiper in its limiting positions. Determine the maximum angular displacement (throw) of the wiper.arrow_forwardReport on practical activity related to internal combustion engines. Select any 2 mechanisms related with internal combustion engines or supporting mechanisms to transfer motion from crank shaft to the wheels. 1. State the application of the selected mechanism. 2. Show the block diagrams of the selected mechanisms. 3. Explain the types of kinematic links used in the selected mechanism. 4. Explain the types of kinematic pairs used in the selected mechanisms based on the following a) Nature of contact b) Nature of relative motion c) Nature of mechanical constraint. 5. Explain degree of freedom of the selected mechanisms. Note: Avoid choosing slider crank mechanismarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY