AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
7th Edition
ISBN: 9780357096789
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 40, Problem 6ASRQ
While diagnosing the cause of a clicking noise that is heard only when the car is turning: Technician A says that the most probable cause is a worn wheel bearing. Technician B says that the most probable cause is a worn outboard CV joint. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
When discussing the possible causes for a shudder during acceleration,
Technician A says that a worn inner CV joint could be the cause.
Technician B says that insufficient differential gear backlash could be the cause of the problem.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
When reviewing the procedure for replacing an axle boot,
Technician A says that the position of the old boot should be marked on the shaft before removing it.
Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
A vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced.
Technician A says that the left inner CV joint may be the source of the noise.
Technician B says that the left outer CV joint may be causing the noise.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
Chapter 40 Solutions
AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be reused if it is not damaged or scored. Technician B says that it is normal for the inboard pad to be slightly more worn than the outside pad. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhen discussing shift problems, Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. Technician B that poor shift boot alignment can cause a transaxle to jump out of gear. says Who is correct? A. A only C. Both A and B B. B only D. Neither A nor Barrow_forwardvehicle is producing a sharp, metallic rappingsound originating in the upper portion of the engine.It is most noticeable during idle. Technician A diagnosesthe problem as piston pin knock. Technician Bsays that the problem is most likely a loose crankshaftthrust bearing. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forward
- Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forwardHello, I am trying to study for a test and found this practice review but I'd like to be able to check my work. Can someone help answer some of these questions? Thank youarrow_forwardWhen replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on another. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- A discussion concerning CV joint testing is being held. Technician A says that a recommended method to check CV joints is to raise the vehícle so that the lower control arms are hanging freely; at this point the engine can be accelerated while noise checks can be performed. Technician B says that the vehicle should be road tested so that the CV joints can be checked under load. Who is correct? O a. A only O b. B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct? a. Technician A only b.Technician B only c.Both A and B d.Neither A nor Barrow_forwardWhich of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc. Engined. All of the abovearrow_forward
- 2. Technician A says that the purpose of the steering wheel holder is to make sure that the steeringwheel is centered after the alignment. Technician B says that if the steering wheel is not centered after an alignment, it should be pulled offthe column and positioned correctly. Who iscorrect?a. Technician A c. Both A and B b. Technician B d. Neither A nor Barrow_forwardWhile discussing the possible causes for damage to the surface of a pressure plate.Technician A says a worn clutch disc can score the surface. Technician B saysinsufficient pedal free travel can cause it to overheat. Who is correct?a. Technician Ac. Both A and Bb. Technician Bd. Neither A nor Barrow_forwardTechnician A says that on most vehicles, the wheel/tire assembly is considered sprung weight . Technician B says that low unsprung weight makes the vehicle handle better on irreg ular surfaces. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License