Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Question
Chapter 5, Problem 9MC
To determine
The incorrect statement about Press fit.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following statements about items that are press fit is NOT true?
Group of answer choices
The press fit allows slight motion between the parts and therefore prevents wear
Many precision gears and bearings have a slight interference fit when installed on a shaft or housing
The removal of gears and bearings that are press fit must be done carefully to avoid breaking or binding the parts
A puller with the proper jaws and adapters should be used when applying force to remove press-fit parts
Under staticload or when static load is applied ,most of the machine elements re failed
True
False
Choose the correct device pair from the following which is a common example for lower pair and self-closed pair.
a.
Roller and rings of bearing.
b.
Cam and follower.
c.
Gear mesh with another gear.
d.
Nut and bolt.
Chapter 5 Solutions
Automotive Technology
Ch. 5 - Explain how to properly use and care for a...Ch. 5 - List some common uses ot the dial indicator.Ch. 5 - Wrenches are available in several styles. List and...Ch. 5 - How do manufacturers inform technicians about...Ch. 5 - Prob. 5SACh. 5 - Describe three sources of service information...Ch. 5 - Prob. 1MCCh. 5 - Which of the following wrenches is the best choice...Ch. 5 - Technician A says that a micrometer can be used to...Ch. 5 - Prob. 4MC
Ch. 5 - Which of the following screwdrivers is like a...Ch. 5 - Technician A says most US bolts have a thread...Ch. 5 - Technician A uses a punch to align holes in parts...Ch. 5 - An extractor is used for removing broken. seals...Ch. 5 - Prob. 9MCCh. 5 - Technician A uses a blowgun to blow off parts...Ch. 5 - Technician A says that flare nut or line wrenches...Ch. 5 - Technician A uses a dial indicator to take inside...Ch. 5 - For a measurement that must be made within one...Ch. 5 - Technician A says that jack stands should always...Ch. 5 - When using an air impact wrench. Technician A uses...Ch. 5 - While discussing thread sealants and lubricants:...Ch. 5 - The metric equivalent to 10 miles is. 0.06895 bar...Ch. 5 - Which of the following thread designs typically...Ch. 5 - Which of the following is not measured with a...
Knowledge Booster
Similar questions
- While discussing proper band adjustment procedures: Technician A says that on some vehicles the bands can be adjusted externally with a torque wrench. Technician B says that a calibrated inch- pound torque wrench is normally used to tighten the band adjusting bolt to a specified torque. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardIt is a wrench that has a movable jaw which makes it adjustable to various sizes of nuts [(a Double ended wrench (b)adjustable wrench (c) plier (d) combination wrencharrow_forward30. Which of the following is NOT a spring type used in pressure plate assemblies?A. Belleville B. CoilC. Diaphragm D. Torsionalarrow_forward
- #3 vibration, will upvote anyone who will answers thanks. Complete solution and correct units plsarrow_forwardIn deep groove ball bearings, the surface of shaft slides over the surface of bush which results in wear and friction. Select one: True Falsearrow_forwardFrom the following identify a false statement regarding the adjustment of drive belt tension for lathe machine. a.Check the belt tension by applying finger pressure any point between the two pulleys b.Visual inspect the drive belts for cracks and if noticed replace them with a matched set of belt c. Visual inspect the drive belts for excessive wear and if noticed replace them with a matched set of belt d.Check the belt tension by applying finger pressure on each belt at midway between the two pulleysarrow_forward
- need correctly all the parts with explanation true or fals earrow_forwardCast iron is used to make rollers as it has superior compression load. Select one: True Falsearrow_forwardTechnician A uses a micrometer to measure the connecting rod journal for taper. Technician B uses a micrometer to measure the connecting rod journal for out-of-roundness. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forwardTrue /false Fulcrum can be only located at one end of the lever.a) Trueb) Falsearrow_forwardq10 Applying finger pressure on the belt near the pulley end is not the correct method to check the tension of the belt drive of a lathe machine. Select one: True Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning