Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 5, Problem 12MC
Technician A uses a dial indicator to take inside and outside measurements. Technician B uses a dial caliper to take inside, outside, and depth measurements. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Spindle is a part of a measuring instrument and it belongs to
a.
Vernier height gauge
b.
Micrometer
c.
Vernier Caliper
d.
Dial test indicator
Technician A says that a micrometer can be used tomeasure the outside diameter of something. TechnicianB says that a vernier caliper can be used to measurethe inside diameter of a bore. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
Identify from the following measuring instrument, that can do Direct measurement.
a. Vernier Caliper
b. Micrometer
c. Vernier Caliper
d. Dial test indicator
Chapter 5 Solutions
Automotive Technology
Ch. 5 - Explain how to properly use and care for a...Ch. 5 - List some common uses ot the dial indicator.Ch. 5 - Wrenches are available in several styles. List and...Ch. 5 - How do manufacturers inform technicians about...Ch. 5 - Prob. 5SACh. 5 - Describe three sources of service information...Ch. 5 - Prob. 1MCCh. 5 - Which of the following wrenches is the best choice...Ch. 5 - Technician A says that a micrometer can be used to...Ch. 5 - Prob. 4MC
Ch. 5 - Which of the following screwdrivers is like a...Ch. 5 - Technician A says most US bolts have a thread...Ch. 5 - Technician A uses a punch to align holes in parts...Ch. 5 - An extractor is used for removing broken. seals...Ch. 5 - Prob. 9MCCh. 5 - Technician A uses a blowgun to blow off parts...Ch. 5 - Technician A says that flare nut or line wrenches...Ch. 5 - Technician A uses a dial indicator to take inside...Ch. 5 - For a measurement that must be made within one...Ch. 5 - Technician A says that jack stands should always...Ch. 5 - When using an air impact wrench. Technician A uses...Ch. 5 - While discussing thread sealants and lubricants:...Ch. 5 - The metric equivalent to 10 miles is. 0.06895 bar...Ch. 5 - Which of the following thread designs typically...Ch. 5 - Which of the following is not measured with a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- For a measurement that must be made within one ten-thousandth of an inch. Technician A uses a machinists rule. For the same accuracy. Technician B uses a standard micrometer. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that a micrometer can be used to measure the outside diameter of something. Technician B says that a vernier caliper can be used to measure the inside diameter of a bore. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardThe depth measurement is done by ___________________part of a Vernier Caliper. Ratchet Anvil Spindle Bladearrow_forward
- 4 ___________ tool is used for verifying the flatness of the component. A. Protractor B. Engineer square C. Micrometer D. Spirit levelerarrow_forwardAppropriate instrument to check the flatness of slip gauge is, (a) dial indicator (b) pneumatic comparator (c) optical interferometer. (d) tool makers microscope with projection facilityarrow_forward9 - Which is the measuring instrument used to carry angles? A) Vernier caliper B) Miter C) Digital indicator D) Fork Gauge E) Dial Surface Gaugearrow_forward
- This method is to correct error with the use of external standards A. Measuring a blank B. Measuring accuracy C. None of the above D. Measuring a precision E. Measuring the end pointarrow_forwardWhat are the advantages and disadvantages of the measuring instruments: a) meter rule b) vernier caliper c) micrometer screw gaugearrow_forward5 In micrometer, circular scale is found on the thimble. Select one: True Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY