Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 55, Problem 14RQ
All of these are good reasons for replacing an accumulator unit, except
- The accumulator/dryer is punctured.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
FLUID POWER SYSTEMS
Excluding lines, which of the following components are required to make simple hydrolic system?
A) Reservoir, pump, filter & regulator.
B) Reservoir, ACOV, pressure relief valve & actuator.
C) Reservoir, pump, selector valve & actuator.
6
In absorption cooling system, Water can never be used as working fluid.
Select one:
True
False
Chapter 55 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 55 - What should you do if you suspect that an...Ch. 55 - Explain how dye can be used to find leaks in the...Ch. 55 - What is the purpose of the thermostatic switch in...Ch. 55 - Why should the probe of an electronic leak...Ch. 55 - How will air trapped in the A7C system affect...Ch. 55 - Which of the following statements best defines the...Ch. 55 - Which of the following statements is not true...Ch. 55 - To charge an air-conditioning system while it is...Ch. 55 - All of the following are true statements about...Ch. 55 - A very important part of a performance test on an...
Ch. 55 - While conducting a pressure test on an A/C system,...Ch. 55 - The high-side pressure on a system with a cycling...Ch. 55 - When checking an A/C system, the evaporators inlet...Ch. 55 - All of these are good reasons for replacing an...Ch. 55 - In an AZC system, if the low-side pressure is...Ch. 55 - Technician A says that evacuating (pumping down)...Ch. 55 - Technician A says that some refrigerant leaks can...Ch. 55 - Technician A says that the presence of oil around...Ch. 55 - Technician A says that a faulty accumulator will...Ch. 55 - Technician A says that air in the system can cause...Ch. 55 - Technician A feels up and down the face or along...Ch. 55 - Technician A says that a manifold gauge set can be...Ch. 55 - While discussing an inoperative blend air door:...Ch. 55 - Two technicians were discussing how comparing the...Ch. 55 - While conducting an A/C system performance test:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is the function of the oil return hole or orifice in a suction accumulator?arrow_forwardAre the best vacuum pumps one-stage or two-stage?arrow_forwardWhen condenser tubes become fouled, they may be cleaned by A. using a steel brush. B. using a brass brush. C. using a chisel and hammer. D. running a mixture of sand and water through them.arrow_forward
- Why do some condensers have to be cleaned with brushes and others with chemicals?arrow_forwardTechnician A says that when the refrigerant is pumped out of the compressor and sent to the condenser, heat in the refrigerant is moved to the outside air by conduction and convection. Technician B says that the refrigerant leaves the bottom of the condenser as a high-pressure, high-temperature liquid. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardDescribe the process of Feedforward Regulation system?arrow_forward
- Why do some condensers have to be cleaned with brushesand others with chemicals?arrow_forward9. While preparing to remove an engine: Technician A disconnects the refrigerant lines at the air-conditioning compressor and allows the refrigerant to totally leak out before removing the compressor. Technician B installs plugs in the ends of the refrigerant hoses after they have been disconnected. Who is correct?arrow_forwardSurface condensers allow the two fluids to mix, is the statement true or falsearrow_forward
- what should you know before choosing a respiratorarrow_forwardWhich of the following tube-in-tube condensers can be cleaned mechanically using a special brush? a) serpentine type b) flanged ends c) serpentine shell It is the upper limit of the compression ratio that compressor manufacturers recommend. b) 3: 1 a) 18: 1 c) 12: 1arrow_forwardWhich of the following statements is not true about orifice tube systems? The suction line must be cool to the touch from the evaporator outlet to the compressor. The liquid line from the condenser outlet to the evaporator inlet should be cool. The evaporator should feel very cold. The accumulator must be cool to the touch.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY