A reducing elbow in a horizontal pipe is used to deflect water flow by an angle
Want to see the full answer?
Check out a sample textbook solutionChapter 6 Solutions
FLUID MECHANICS FUNDAMENTALS+APPS
Additional Engineering Textbook Solutions
Thermodynamics: An Engineering Approach
Machine Tool Practices (10th Edition)
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Vector Mechanics for Engineers: Statics and Dynamics
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
- Water is flowing through a 15-cm-diameter pipe that consists of a 3-m-long vertical and 2-m-long horizontal section with a 90° elbow at the exit to force the water to be discharged downward, as shown, in the vertical direction. Water discharges to atmospheric air at a velocity of 5 m/s, and the mass of the pipe section when filled with water is 17 kg per meter length. Determine the moment acting at the intersection of the vertical and horizontal sections of the pipe (point A). What would your answer be if the flow were discharged upward instead of downward?arrow_forwardA pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectivelyarrow_forwardA ball weighing 1 kg is “floating" on a circular jet, as shown in the figure (ignore the wire, which is there to stabilize the weight). The jet leaving the orifice at the bottom has an upward velocity of 10 m/s, and the jet diameter at the exit is 2 cm. Assuming the jet spills sideways at 90°, find the height h at which the ball will float. Jet D1 =0.02 m W1 = 10 -arrow_forward
- A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50 g and is charged with 100 g of water. The pressure inside the rocket is 100 kPa gage. The exit area is one-tenth of the chamber crosssectional area. The inside diameter of the rocket is 5 cm. Assume that Bernoulli's equation is valid for the water flow inside the rocket. Neglecting air friction, calculate the maximum velocity it will attain. 5 cm PROBLEM 6.90 100 kPaarrow_forward6-23 A reducing elbow in a horizontal pipe is used to deflect water flow by an angle 0 = 45° from the flow direction while accelerating it. The elbow discharges water into the atmo- sphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 50 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum- flux correction factor to be 1.03 at both the inlet and outlet. 150 cm² Water 30.0 kg/s FIGURE P6-23 25 cm² 15- 40 cmarrow_forwardA 90° elbow in a horizontal pipe is used to direct water flow upward at a rate m of 37 kg/s. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the density of water to be 1000 kg/m³ and the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. Water m kg/s O 50 cm Determine the anchoring force needed to hold the elbow in place. The anchoring force needed to hold the elbow in place is The resultant direction of the force is 155 429 N.arrow_forward
- a hemispherical bowl of a radius 10m is filled with water. There is a small hole of radius 10cm at the bottom of the convex surface. assume that the velocity of efflux of the water when the water level is at height h(m) is v=0.14 sqrt 2gh. Determine the time in hours taken for the bowl to empty.arrow_forward6-22 A 90° elbaw is used to direct water flow at a rate of 25 kgis in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03. 35 cm Water 25 kg/sarrow_forwardkg Water (p = 1000- -) flows through the elbow below. The diameter of both the inlet and outlet is 1.1 cm, and the velocity through the nozzle is V =4.5 m/s. The outlet m³ has an angle of 0 =15 degrees. The water is at a pressure of 29 kPa (gauge). Find the magnitude of the force on the elbow. 0 Varrow_forward
- A 30-cm-diameter, 10-cm-high vertical cylindrical vessel equipped with a vertical tube at the edge is rotated about its vertical axis at a constant angular velocity of 15 rad/s. If the water rise in the tube is 30 cm, determine the net vertical pressure force acting on the vessel.arrow_forwardDetermine the magnitude and direction of the resultant force exerted on this double nozzle by water flowing through it as shown in the figure below. Both nozzle and jet have a velocity of 8.6 m/s and 11.5 m/s. The axis of both nozzles lies in a horizontal plane. 8.6 vn 12 cm Jet 17 Cm 7270 * 11.5 /s 8.6 jetarrow_forwardA large, open-topped water tank is being filled from above by a 1.0-cm-diameter hose. The water in the hose has a uniform speed of 11 cm/s. Meanwhile, the tank springs a leak at the bottom. The hole has a diameter of 0.70 cm. Determine the equilibrium level heq of the water in the tank, O measured relative to the bottom, if water continues flowing into the tank at the same rate. heq 1.26 X10-3 Incorrect marrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY