FLUID MECHANICS FUNDAMENTALS+APPS
4th Edition
ISBN: 2810022150991
Author: CENGEL
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Question
Chapter 6, Problem 86P
To determine
The relation for the constant
The relation for the velocity of the soldier.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
At what maximum speed does a compressed air torpedo move, which expells 18 kg of air every second at a speed of 118 m/s? The force of water resistance is proportional to the square of the velocity and is equal to 480 N at a speed of 21 m/s. (The solutiom is 44 m/s)
Water is flowing in a pipeline 600 cm above datum level has a velocity of 10 m/s
and is at a gauge pressure of 30 KN/m2. If the mass density of water is 1000
kg/m3, what is the total energy per unit weight of the water at this point? Assume
.acceleration due to Gravity to be 9.81 m/s2
5m O
11 m
111 m O
609 m O
The value of frictional force and acceleration of block of mass 10 kg in the figure are
J60°
10 kg
4kg
μ-0.4
(A) 10 N, 1 m/s²
(B) 20 N, 2 m/s?
(C) 20 N, 0 m/s?
(D) 10 N, 0 m/s²
Chapter 6 Solutions
FLUID MECHANICS FUNDAMENTALS+APPS
Ch. 6 - Express Newton’s second law of motion for rotating...Ch. 6 - Express Newton’s first, second, and third laws.Ch. 6 - Is momentum a vector? If so, in what direction...Ch. 6 - Express the conservation of momentum principle....Ch. 6 - How do surface forces arise in the momentum...Ch. 6 - Explain the importance of the Reynolds transport...Ch. 6 - What is the importance of the momentum-flux...Ch. 6 - Write the momentum equation for steady...Ch. 6 - In the application of the momentum equation,...Ch. 6 - Two firefighters are fighting a fire with...
Ch. 6 - A rocket in space (no friction or resistance to...Ch. 6 - Describe in terms of momentum and airflow how a...Ch. 6 - Does it take more, equal, or less power for a...Ch. 6 - In a given location, would a helicopter require...Ch. 6 - Describe body forces and surface forces, and...Ch. 6 - A constant-velocity horizontal water jet from a...Ch. 6 - A horizontal water jet of constant velocity V from...Ch. 6 - A horizontal water jet from a nozzle of constant...Ch. 6 - A 2.5-cm-diameter horizontal water jet with a...Ch. 6 - A 90 elbow in a horizontal pipe is used to direct...Ch. 6 - Repeat Prob. 6-20 for the case of another...Ch. 6 - A horizontal water jet impinges against a vertical...Ch. 6 - Water enters a 7-cm-diameter pipe steadily with a...Ch. 6 - A reducing elbow in a horizontal pipe is used to...Ch. 6 - Repeat Prob. 6-24 for the case of = 125°.Ch. 6 - A 100-ft3/s water jet is moving in the positive...Ch. 6 - Reconsider Prob. 6-26E. Using appropriate...Ch. 6 - Commercially available large wind turbines have...Ch. 6 - A fan with 24-in-diameter blades moves 2000 cfm...Ch. 6 - A 3-in-diameter horizontal jet of water, with...Ch. 6 - Firefighters are holding a nozzle at the end of a...Ch. 6 - A 5-cm-diameter horizontal jet of water with a...Ch. 6 - Prob. 33PCh. 6 - A 3-in-diameter horizontal water jet having a...Ch. 6 - An unloaded helicopter of mass 12,000 kg hovers at...Ch. 6 - Prob. 36PCh. 6 - Water is flowing through a 10-cm-diameter water...Ch. 6 - Water flowing in a horizontal 25-cm-diameter pipe...Ch. 6 - Prob. 39PCh. 6 - Water enters a centrifugal pump axially at...Ch. 6 - An incompressible fluid of density and viscosity ...Ch. 6 - Consider the curved duct of Prob. 6-41, except...Ch. 6 - As a follow-up to Prob. 6-41, it turns out that...Ch. 6 - Prob. 44PCh. 6 - The weight of a water tank open to the atmosphere...Ch. 6 - A sluice gate, which controls flow rate in a...Ch. 6 - A room is to be ventilated using a centrifugal...Ch. 6 - How is the angular momentum equation obtained from...Ch. 6 - Prob. 49CPCh. 6 - Prob. 50CPCh. 6 - Prob. 51CPCh. 6 - A large lawn sprinkler with two identical arms is...Ch. 6 - Prob. 53EPCh. 6 - The impeller of a centrifugal pump has inner and...Ch. 6 - Water is flowing through a 15-cm-diameter pipe...Ch. 6 - Prob. 56PCh. 6 - Repeat Prob. 6-56 for a water flow rate of 60 L/s.Ch. 6 - Prob. 58PCh. 6 - Water enters the impeller of a centrifugal pump...Ch. 6 - A lawn sprinkler with three identical antis is...Ch. 6 - Prob. 62PCh. 6 - The impeller of a centrifugal blower has a radius...Ch. 6 - An 8-cm-diameter horizontal water jet having a...Ch. 6 - Water flowing steadily at a rate of 0.16 m3/s is...Ch. 6 - Repeat Prob. 6-66 by taking into consideration the...Ch. 6 - A 16-cm diameter horizontal water jet with a speed...Ch. 6 - Water enters vertically and steadily at a rate of...Ch. 6 - Repeal Prob. 6-69 for the case of unequal anus-the...Ch. 6 - Prob. 71PCh. 6 - Prob. 72PCh. 6 - A spacecraft cruising in space at a constant...Ch. 6 - A 60-kg ice skater is standing on ice with ice...Ch. 6 - A 5-cm-diameter horizontal jet of water, with...Ch. 6 - Water is flowing into and discharging from a pipe...Ch. 6 - Indiana Jones needs So ascend a 10-m-high...Ch. 6 - Prob. 79EPCh. 6 - A walnut with a mass of 50 g requires a force of...Ch. 6 - Prob. 81PCh. 6 - Prob. 82PCh. 6 - A horizontal water jet of constant velocity V...Ch. 6 - Show that the force exerted by a liquid jet on a...Ch. 6 - Prob. 85PCh. 6 - Prob. 86PCh. 6 - Water enters a mixed flow pump axially at a rate...Ch. 6 - Prob. 88PCh. 6 - Water enters a two-armed lawn sprinkler along the...Ch. 6 - Prob. 91PCh. 6 - Prob. 92PCh. 6 - Prob. 93PCh. 6 - Prob. 94PCh. 6 - A water jet strikes a moving plate at velocity...Ch. 6 - Water flows at mass flow rate m through a 90°...Ch. 6 - Prob. 97PCh. 6 - Water shoots out of a Iar2e tank sitting a cart...Ch. 6 - Prob. 99PCh. 6 - Prob. 100PCh. 6 - Prob. 101PCh. 6 - Consider water flow through a horizontal, short...Ch. 6 - Consider water flow through a horizontal. short...Ch. 6 - Prob. 104PCh. 6 - Prob. 105PCh. 6 - Prob. 106PCh. 6 - The velocity of wind at a wind turbine is measured...Ch. 6 - The ve1ocity of wind at a wind turbine is measured...Ch. 6 - Prob. 109PCh. 6 - Prob. 110PCh. 6 - Prob. 111PCh. 6 - Consider the impeller of a centrifugal pump with a...Ch. 6 - Prob. 113PCh. 6 - Prob. 114P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Hydro-machinery such as turbines and pumps represent fluid devices that have wide variety of configurations. Centrifugal pumps add energy to a fluid – by doing work on the fluid to move and increase the pressure. Figure 3 below shows the velocity diagram at the inlet and exit of a centrifugal pump impeller pumping water at 6000 L/min and operating at 1750 rpm. The pump has a blade height, b, of 6cm with ri = 4cm and r2 = 16cm, with an exit blade angle B2 = 22°. Assume ideal flow conditions and that the tangentia! velocity component of the water entering the blade is zero. Analyze the pump in terms of tangential velocity component at the exit Ve2, the ideal head W shaft rise hi, and the power transferred to the fluid Jaz V Figure 3arrow_forwardWater discharge from a pipe of diameter 0.05 m into a tank for exactly 11 min. Knowing that the increased in the tank weight is 18 kN. Water density is 1000 kg/m, g= 9.81 m/s. Answer the following: What is the mass flow rate of water into the tank (kg/min). What is the discharge of water into the tank in cubic meters per minute. What is the mean velocity of the water that flow from the pipe ( m/s).arrow_forwardA set of 20 stairs, each of 20 cm height, is ascended by a 700 N man in a period of 1.25 s. Calculate the mechanical work, power, and change in potential energy during the ascent.arrow_forward
- Air is flowing steadily in an insulated duct. The pressure and temperature measurements of the air at two stations A and B are given below. Establish the direction of the flow of air in the duct. Assume that for air, specific V 0.287 where p, v, and T р T Р heat c is constant at 1.005 kJ/kg K, h = c T, and are pressure (in kPa), volume (in m³/kg) and temperature (in K) respectively. Station A Station B Pressure Temperature 130 kPa 50°C 100 kPa 13°Carrow_forwardIn typical jet-engine testings, a static thrust stand similar to the one shown below is used to mount the engine. In engine testing, pressure is usually expressed in gauge pressure. At the engine inlet, air is steadily introduced, and its cross-sectional area is 1.2 m². The inlet condition is given by 250 m/s, 50 kPa (gauge) and -50°C. The nozzle-exhaust gas has a velocity of 550 m/s, and its absolute pressure is 101 kPa, the same as the atmospheric pressure. (a) Estimate the thrust force applied to the stand during the engine testing. Assume that the incoming air has the same mass flow rate as the exhaust gas. (b) Repeat (a) when fuel supplied to the engine is taken into account. The fuel mass flow rate into the engine is equal to 2% of the mass flow rate of incoming air. Which thrust force is likely to provide more accurate estimation? 250 m/s 50 kPa -50°C Jet engine Open atmosphere 550 m/s 0 kPa Static thrust stand Thrustarrow_forwardVery small particles moving in a fluid are known to experience a forcedrag proportional to speed. Consider a particle with a net weightW is dropped into a fluid. Particles experience drag, FD = kV,where V is the velocity of the particle. Determine the time required for the particle toaccelerates from rest to 95 percent of its terminal speed(stopping) Vt, in terms of k, W, and g.arrow_forward
- A body has a mass of 18 kg falls freely from rest. After falling 235 m, what will its velocity be just before impact. Neglect air frictionarrow_forwardA fire hose is shooting water at a refrigerator at 10 kg/s with a velocity of 10 m/s. This flow is perpendicular to the surface and all water flows off parallel to the surface (ie no "x" direction in outflow). The friction on the ground which must be overcome to cause the refrigerator to move is 50 N. The refrigerator is 2 m tall and 0.8m wide and 1 m deep. It weights 200 kg (which you may assume to be evenly distributed). Will it move? If no what is the initial acceleration?arrow_forwardA water container is kept on a weighing balance. Water from a tap is falling vertically into the container with a volume flow rate of Q; the velocity of the water when it hits the water surface is U. At a particular instant of time the total mass of the container and water is m. The force registered by the weighing balance at this instant of time is (a) mg + pQU (c) mg + PQU2/2 (b) mg + 2PQU (d) pQU?/2arrow_forward
- A water jet with volume flow rate of 3 m³/s is moving in the positive x- direction at a speed of 6 m/s. The stream hits a stationary splitter, such that half of the flow is diverted upward at 45º and the other half is directed downward at 45°, and both streams have a final average speed of 6 m/s. The gravitational effects and friction loss are considered to be negligible. Determine the x- and z-components of the force required to hold the splitter in place against the water force. Note that the pressure of the water jet at inlet and outlet sections is the atmospheric pressure and the density of water is taken as 1000 kg/m³. 3 m³/s 6 m/s 45° A 45° Figure 3.1 2 FR: FRXarrow_forwardA boat moved by jet propulsion discharges water through a jet of area 0.02 m2; the water being drawn from inlet opening facing the direction of motion. The total drag is estimated to be 17.66 u2 N·m where u is the speed of the boat in metre per second. Take density of water at 1,020 kg/m3 and efficiency of the pump set is 78%. If the boat moves at 54 kilometers per hour, determine the following: A) Relative velocity of the jet in meters per second B) The power, in kilowatts, of the motor required to work the pumps C) Efficiency of propulsion, in %arrow_forwardDetermine the volume flow rate and the mass flow rate of fuel from the gasoline tank to the fuel injection system of a car traveling at a constant speed on a flat road with the parameters given below: Speed of the car: 60.0 mpg gasoline consumption: 20.0 mpg The specific gravity of gasoline is given as 0.72. Express the answers in cm3/s and kg/hr.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license