SYSTEM DYNAMICS>LOOSELEAF<
3rd Edition
ISBN: 9781260163087
Author: Palm
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 7.46P
The copper shaft shown in Figure P7.46 consists of two cylinders w ith the following dimensions: — 10 mm, L2=5 mm, Dj = 2 mm, and D2= 1.5 mm. The shaft is insulated around its circumference so that heat transfer occurs only in the axial direction, (a) Compute the thermal resistance of each section of the shaft and of the total shaft. Use the follow ing value for the conductivity of copper: k = 400 W/m • °C. (b) Compute the heat flow rate in the axial direction if the temperature difference across the endpoints of the shaft is 30°C.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Water vapor at a temperature of 120 ° C flows through a stainless steel pipe (k = 57 W / mK). The inner diameter of the pipe is 47 mm, the outer diameter is 50 mm, and the length is 100 m. The heat transfer coefficient between the water vapor and the pipe wall is 200 W / m²K, and the heat transfer coefficient between the outer surface of the pipe and the ambient air is 25 W / m_K. The outdoor air temperature is 10 ° C. Find the thermal conductivity coefficient of the insulation material, since it is desired to insulate with an insulation material with a layer thickness of 50 mm in order to reduce the loss of heat from the pipe by 60%.
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations? Known, Find, Schematic Diagram, Assumption, Properties, Analysis and Comments
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?
Chapter 7 Solutions
SYSTEM DYNAMICS>LOOSELEAF<
Ch. 7 - Prob. 7.1PCh. 7 - Refer to the water storage and supply system shown...Ch. 7 - Prob. 7.3PCh. 7 - In Figure P7.4 the piston of area A is connected...Ch. 7 - Refer to Figure 7.1.4a. and suppose that p\ — p2=...Ch. 7 - Pure water flows into a mixing tank of volume V =...Ch. 7 - Consider the mixing tank treated in Problem 7.6....Ch. 7 - Derive the expression for the fluid capacitance of...Ch. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - 7.11 Derive the expression for the capacitance of...Ch. 7 - Air flows in a certain cylindrical pipe 1 m long...Ch. 7 - Derive the expression for the linearized...Ch. 7 - Consider the cylindrical container treated in...Ch. 7 - A certain tank has a bottom area A = 20 m2. The...Ch. 7 - A certain tank has a circular bottom area A = 20...Ch. 7 - The water inflow rate to a certain tank was kept...Ch. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - In the liquid level system shown in Figure P7.20,...Ch. 7 - The water height in a certain tank was measured at...Ch. 7 - Derive the model for the system shown in Figure...Ch. 7 - (a) Develop a model of the two liquid heights in...Ch. 7 - Prob. 7.24PCh. 7 - Design a piston-type damper using an oil with a...Ch. 7 - Prob. 7.26PCh. 7 - 7.27 An electric motor is sometimes used to move...Ch. 7 - Prob. 7.28PCh. 7 - Prob. 7.29PCh. 7 - Figure P7.3O shows an example of a hydraulic...Ch. 7 - Prob. 7.31PCh. 7 - Prob. 7.32PCh. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - (a) Determine the capacitance of a spherical tank...Ch. 7 - Obtain the dynamic model of the liquid height It...Ch. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Prob. 7.42PCh. 7 - Prob. 7.43PCh. 7 - Prob. 7.44PCh. 7 - Prob. 7.45PCh. 7 - The copper shaft shown in Figure P7.46 consists of...Ch. 7 - A certain radiator wall is made of copper with a...Ch. 7 - A particular house wall consists of three layers...Ch. 7 - A certain wall section is composed of a 12 in. by...Ch. 7 - Prob. 7.50PCh. 7 - Prob. 7.51PCh. 7 - A steel tank filled with water has a volume of...Ch. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- SOLVE STEP BY STEP DONT USE CHATGPT There is a horizontal PVC pipe (k=0.16 W/m°C) with a diameter of 15 cm, a wall of 3 mm and a length of 8 m. The external surface of PVC is at 19 °C. Inside this pipe is placed a steel pipe (k=45 W/m.°C), 7 em in external diameter and 2 mm thick, also 8 m long, where saturated steam circulates at 0.38 m. /s and 1.3 atm pressure. The temperature of the steel is at the same temperature of the steam. The annular space between the two pipes is filled with static air. Determine the heat flow that occurs from the steam to the outside of the system.arrow_forward4.16 Estimate the convective heat-transfer coefficient for natural convection from a horizontalsteam pipe. The outside surface temperature of the insulated pipe is 80°C. Thesurrounding air temperature is 25°C. The outside diameter of the insulated pipe is 10 cm. 4.17 A vertical cylindrical container is being cooled in ambient air at 25°C with no air circulation.If the initial temperature of the container surface is 100°C, compute the surfaceheat transfer coefficient due to natural convection during the initial cooling period. Thediameter of the container is 1 m, and it is 2m higharrow_forwardThe composite wall of a furnace consists of three different materials, two of which have known thermal conductivity (ka = 20 W/m°C and kc = 50 W/m°C) and thicknesses La = 0.30 m and Lb = 0.15 m. The third material (B) is between A and C, with a thickness of 0.15 m, but its thermal conductivity (kb) is unknown. Under steady-state operating conditions, measurements reveal a temperature of 20 °C on the external surface, 600 °C on the internal surface, and a furnace ambient temperature of 800 °C. The internal convection coefficient is 25 W/m²°C. What is the value of kb?arrow_forward
- A cylinder in a pneumatic circuit extenders under adiabatic conditions to lift a load. Predict the system behavior over time if the cylinder remains extended under constant load.arrow_forwardQ. 5: Assume steady-state, one-dimensional heat conduction through the symmetric shape shown in Figure 1. Assuming that there is no internal heat generation, derive an expression for the thermal conductivity k(x) for these conditions: A(x) = (1 - x), T(x) = 300(1 - 2x - x3), and q = 6000 W, where A is in square meters, T in kelvins, and x in meters. Consider x= 0 and 1.arrow_forward2.15 Suppose that a pipe carrying a hot fluid with an external temperature of and outer radius is to be insulated with an insulation material of thermal conductivity k and outer radius . Show that if the convection heat transfer coefficient on the outside of the insulation is and the environmental temperature is , the addition of insulation actually increases the rate of heat loss if , and the maximum heat loss occurs when . This radius, is often called the critical radius.arrow_forward
- A wood stove heats a small cabin with the following dimensions 8 m x 6 m x 3 m (length x width x height) to 25°C. Of the heat generated by burning wood, 60% is lost up the chimney. The cabin also loses heat through walls, ceiling and floor. Assume that all sides of the house except the floor are insulated with a 10 cm thick polyethylene foam layer having a thermal conductivity htc = 0.038 W/(m•°C). The heat loss through the floor is 1/5 of the heat loss through the ceiling. Outside air is at -5°C. a) How much heat is lost in total from the ceiling, walls, and floor? b) How many kg of wood per hour is needed as fuel for the cabin to maintain its temperature if heat value of wood is AH = 18,000 kJ/kg?arrow_forwardA composite wall is made up of 10 cm of common brick against 15cm of concrete with 1.5 cm of plaster on inside of wall. Assume still air in room at 25 °C. The outside air at 40 °C the wind velocity is 25 km/hr. Note: Use standard tables for values of thermal conductivities and film co-efficient. Find: a) The thermal resistance of wall b) The overall heat transfer cop-efficient. c) The steady state heat transfer rate per unit area of wall d) Heat transfer if the outside and inside film resistances are disgradedarrow_forwardThe composite wall of an oven consists of three materials, two of which are of knownthermal conductivity, kA = 20 W/m – K and kC = 50 W/m – K, and known thickness, LA =0.30 m and LC = 0.15 m. The third material, B, which is sandwiched between materialsA and C, is of known thickness, LB = 0.15 m, but unknown thermal conductivity kB.Under steady – state operating conditions, measurements reveal an outer surfacetemperature of 600 oC, and an oven air temperature of 800 oC. The inside convectioncoefficient h is known to be 25 W/m2 – K. total rate of heat transfer = 550 W/m2.What is the value of kB?arrow_forward
- (a) A circular copper ring at 24.0°C has a hole with an area of 9.97 cm2. What minimum temperature must it have so that it can be slipped onto a steel metal rod having a cross-sectional area of 10.0 cm2?_______ °C(b) Suppose the ring and the rod are heated simultaneously. What change in temperature of both will allow the ring to be slipped onto the end of the rod? (Assume no significant change in the coefficients of linear expansion over this temperature range.)________ °Carrow_forwardAn oven made of stone with 3 m length and semi-cylindrical shape losses heat from inlet section of the surface shell (ri = 50 cm) to outlet section (ro = 62 cm) by convection and radiation. According to the systemconditions showing on the following figure; calculate Ti value if To temperature is 35 °C (Assume steady state and onedimensional condition and ε = 0,90; σ = 5,67x10-8 W/m2K4)arrow_forwardA tank, Figure Q5, of a mass of 1850 kg is supported by four metal alloy (E = 50GPa) columns of a tubular cross-section with an outer diameter do = 64 mm and a thickness t = 3 mm. The columns are assumed to be loaded equally and securely fixed to the tank and to a brace at 1.2 m from the ground. The brace itself is supported by four other columns with the same cross-sectional and material properties to those supporting the tank but are assumed to be firmly fixed to the brace and free at the ground level. With respect to Euler buckling, calculate the factor of safety for the columns below the brace and the maximum length, L1 of the columns above the brace to achieve the same factor of safety.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license