SYSTEM DYNAMICS>LOOSELEAF<
3rd Edition
ISBN: 9781260163087
Author: Palm
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 7.7P
Consider the mixing tank treated in Problem 7.6. Generalize the model to the case where the tank’s volume is V m\ For quality control purposes, we want to adjust the output concentration soby adjusting the input concentration s, . How much volume should the tank have so that the change in solags behind the change in s, by no more than 20 s?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Aiming a 1.69 in diameter garden hose straight up, forms a “bubbler fountain” that you could easily drink from (but you shouldn’t because of bacteria, etc.). The water flows out the hose and down the sides. If the water has a density of 63.1 lbm/ft^3 and a viscosity of 0.0119 g/cm*s, what is the thickness of the water film (df) (in cm) if the flow rate of water is 6.42 in^3/s? For simplicity, assume the film is thin enough that you can use rectangular coordinates.
(a) If the boundary layer velocity profile for y ≤ δ is given by where U is the velocity at a distance y from the surface, δ is the boundary layer thickness and Ue is the freestream velocity. (i) Find the ratio of the displacement thickness to the boundary layer thickness (this is a number). (ii) Find the ratio of the momentum thickness to the boundary layer thickness (this is a number). (b) Air enters a two-dimensional duct with a uniform velocity profile. As the boundary layers on the top and bottom walls grow with downstream distance, the velocity in the freestream tends to increase. However, if the walls diverged with downstream distance so that the freestream velocity remained constant, express the angle of divergence of the walls in terms of the boundary layer displacement thickness δ∗ and the distance along the duct x. (c) A laminar boundary layer is observed to grow on a flat plate of width w and length x = L such that the pressure is…
Show step by step solution asap
I will rate Positively .
Chapter 7 Solutions
SYSTEM DYNAMICS>LOOSELEAF<
Ch. 7 - Prob. 7.1PCh. 7 - Refer to the water storage and supply system shown...Ch. 7 - Prob. 7.3PCh. 7 - In Figure P7.4 the piston of area A is connected...Ch. 7 - Refer to Figure 7.1.4a. and suppose that p\ — p2=...Ch. 7 - Pure water flows into a mixing tank of volume V =...Ch. 7 - Consider the mixing tank treated in Problem 7.6....Ch. 7 - Derive the expression for the fluid capacitance of...Ch. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - 7.11 Derive the expression for the capacitance of...Ch. 7 - Air flows in a certain cylindrical pipe 1 m long...Ch. 7 - Derive the expression for the linearized...Ch. 7 - Consider the cylindrical container treated in...Ch. 7 - A certain tank has a bottom area A = 20 m2. The...Ch. 7 - A certain tank has a circular bottom area A = 20...Ch. 7 - The water inflow rate to a certain tank was kept...Ch. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - In the liquid level system shown in Figure P7.20,...Ch. 7 - The water height in a certain tank was measured at...Ch. 7 - Derive the model for the system shown in Figure...Ch. 7 - (a) Develop a model of the two liquid heights in...Ch. 7 - Prob. 7.24PCh. 7 - Design a piston-type damper using an oil with a...Ch. 7 - Prob. 7.26PCh. 7 - 7.27 An electric motor is sometimes used to move...Ch. 7 - Prob. 7.28PCh. 7 - Prob. 7.29PCh. 7 - Figure P7.3O shows an example of a hydraulic...Ch. 7 - Prob. 7.31PCh. 7 - Prob. 7.32PCh. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - (a) Determine the capacitance of a spherical tank...Ch. 7 - Obtain the dynamic model of the liquid height It...Ch. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Prob. 7.42PCh. 7 - Prob. 7.43PCh. 7 - Prob. 7.44PCh. 7 - Prob. 7.45PCh. 7 - The copper shaft shown in Figure P7.46 consists of...Ch. 7 - A certain radiator wall is made of copper with a...Ch. 7 - A particular house wall consists of three layers...Ch. 7 - A certain wall section is composed of a 12 in. by...Ch. 7 - Prob. 7.50PCh. 7 - Prob. 7.51PCh. 7 - A steel tank filled with water has a volume of...Ch. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please thanksarrow_forwardWater is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps pleasearrow_forwardWater is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation!arrow_forward
- Hint: Assume your own initial conditionsarrow_forwardYou are being tasked as a wind tunnel engineer to investigate the performance of newly designed high-speed wind tunnel in UPNM. An exhaust gas flows through a nozzle where the inlet area is 5,000 cm2.At this inlet, the gas has a velocity of 1,200 m/s, temperature of 1,500oC,and pressure of 6,000 kPa. Initial measurement revealed that the pressure at the exit of the wind tunnel is 100 kPa. Based on this information, analyze and investigate ; i. Mach number at inlet of the nozzle ii. The velocity of gas at exit iii. The area of the nozzle at exit Take specific heat ratio for the exhaust gas, ? to be 1.7 and the gas constant, R to be 205 J/kg.arrow_forwardCompute the potential evaporation for amsterdam for the month of july if the net radiation is 361 Watts square meter temperature is 15 degrees celsius, transfer coefficient is 0.00298 mm per day pascal, 50% relative humidity, wind speed 1.26 m/s and psychometric constant of 36 pascal per degree celsius use energy balance, aerodynamic and combined methodarrow_forward
- A steam generator generates flue gas at an average temperature of 260 C inside a Chimney. The theoretical draft is 0.5 kPa and the ambient condition of the air is 21 C and 100 kPa. Assume the coefficient velocity to be 0.30 and the molecular weight of the flue gas is 32. For air-fuel ratio requirements per second of 15, calculate: a. The diameter of the Chimney, meter b. The theoretical draft, cm H₂Oarrow_forward2. Find the Diameter of a wind turbine rotor which generates 210 kW of electrical power output in a steady wind velocity of 8.5 m/sec with the power coefficient is 63%. The gear, generator and electric efficiencies are 95%, 96% and 89% respectively. Assume the atmospheric air condition is 1.01325 bar, Gas Constant R = 287 J/kg K at 29°C.arrow_forwardThis subject is Statics of Rigid Bodies. Show your solution step by steparrow_forward
- A cylindrical tank (1.20m in diameter) contains two liquids with the follow specific gravities:LIQUID 1: oil (s.g.oil = 0.80)LIQUID 2: water (s.g.water = 1.00)Each specified liquid has a thickness of 0.60m with the denser liquid at the bottom. If a circular office is placed at the bottom of the tank (100mm in diameter and with c = 0.65) to drain the fluids: Compute for the time required to remove the denser liquid from the tankarrow_forwardSolve quickly with me time 35 minutes ........ A hospital operation room of dimensions 6×8×3 m³ is occupied by 8 persons. The inside design condition is 24°C and 50% relative humidity while the outside design condition is 37°C dry bulb temperature and 60% relative humidity. Calculate the sensible, latent, and the total cooling loads in Tons of refrigeration due to the required ventilation if the air change per hour Nvent=6arrow_forwardSuppose a reactor producing exhaust gas that is being transferred to the next building by a 6 mm diameter and 20 m long uninsulated pipe for testing. The exhaust gas enters the pipe at 200 °C with a low rate of 0.003 kg/s. You can assume that the pipe is thin. It’s spring outside and wind is blowing at 5 m/s, while the outside temperature is 15 °C (59 °F). Properties of gas (assume, air) inside of the pipe (assume, Tm = 380 K, 1 atm): cp = 1012 J/kg⋅K, k = 0.0323 W/m⋅K, μ = 221.6 × 10-7 N⋅s/m2, Pr = 0.694; Properties of air outside: Air (assume, Tavg = 340 K, 1 atm): k = 0.0253 W/m⋅K, α = k/ρcp = 2.99x10‒5 m2/s, ν = 14.82 × 10-6 m2/s, Pr = 0.710, β = 1/Tavg Find ReD and GrD outside of the pipe and determine whether it is free or forced convection Estimate heat transfer coefficient for outside air Is it a fully-developed flow inside of the pipe? Or, it is not relevant here. Estimate heat transfer co-efficient for the inside air Find overall heat transfer coefficient Find…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Hydronics Step by Step; Author: Taco Comfort Solutions;https://www.youtube.com/watch?v=-XGNl9kppR8;License: Standard Youtube License