Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 7.49PP
A home has a sump pump to handle ground water from around the foundation that needs to be removed to a higher elevation. To achieve a flow rate of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A farmer owns an 8-hp engine. He wants to use it to pump water from a 50-ft deep shallow tube well to irrigate his field. What size of centrifugal pump would you recommend to the farmer? Assume 30% system efficiency.
Determine the least number of stages for a multi stage pump to deliver 60L/s against a total head of 210 meters when running at 1453rpm. If the specific speed must not be less than 675.
Compute the water horsepower and electrical power needed for the pump and motor with the following assumptions: a.) Fluid is oil with specific gravity of 0.8 (specific gravity = density of oil/density of water) b.) oil needs to be pumped at a height of 20m, neglect friction loss c.) the volumetric flow rate of the pump = 20 GPM d.) assuming the following efficiences, pump efficiency = 75%, motor efficiency = 90%.
NEEDS COMPLETE SOLUTION, AS SOON AS POSSIBLE. THANK YOU.
Chapter 7 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 7 - A horizontal pipe carries oil with a specific...Ch. 7 - Water at 40 F is flowing downward through the...Ch. 7 - Find the volume flow rate of water exiting from...Ch. 7 - A long DN 150 Schedule 40 steel pipe discharges...Ch. 7 - Figure 7.14 shows a setup to determine the energy...Ch. 7 - A test setup to determine the energy loss as water...Ch. 7 - The setup shown in Fig. 7.16 is being used to...Ch. 7 - A pump is being used to transfer water from an...Ch. 7 - In Problem 7.815 (Fig. 7.17), if the left-hand...Ch. 7 - A commercially available sump pump is capable of...
Ch. 7 - A submersible deep-well pump delivers 745 gal/h of...Ch. 7 - In a pump test the suction pressure at the pump...Ch. 7 - The pump shown in Fig. 7.19 is delivering...Ch. 7 - The pump in Fig. 7.20 delivers water from the...Ch. 7 - Repeat Problem 7.14, but assume that the level of...Ch. 7 - Figure 7.21 shows a pump delivering 840L/min of...Ch. 7 - Figure 7.22 shows a submersible pump being used to...Ch. 7 - Figure 7.23 shows a small pump in an automatic...Ch. 7 - The water being pumped in the system shown in Fig....Ch. 7 - A manufacturer's rating for a gear pump states...Ch. 7 - The specifications for an automobile fuel pump...Ch. 7 - Figure 7.26 shows the arrangement of a circuit for...Ch. 7 - Calculate the power delivered to the hydraulic...Ch. 7 - Water flows through the turbine shown in Fig....Ch. 7 - Calculate the power delivered by the oil to the...Ch. 7 - What hp must the pump shown in Fig. 7.30 deliver...Ch. 7 - If the pump in Problem 7.26 operates with an...Ch. 7 - The system shown in Fig. 7.31 delivers 600 L/min...Ch. 7 - Kerosene (sg = 0.823 ) flows at 0.060m3/s in the...Ch. 7 - Water at 60 F flows from a large reservoir through...Ch. 7 - Figure 7.34 shows a portion of a fire protection...Ch. 7 - For the conditions of Problem 7.31 and if we...Ch. 7 - In Fig. 7.35 kerosene at 25 F is flowing at 500...Ch. 7 - For the system shown in Fig. 7.35 and analyzed in...Ch. 7 - Compute the power removed from the fluid by the...Ch. 7 - Compute the pressure at point 2 at the pump inlet.Ch. 7 - Compute the pressure at point 3 at the pump...Ch. 7 - Compute the pressure at point 4 at the press...Ch. 7 - Compute the pressure at point 5 at the press...Ch. 7 - Evaluate the suitability of the sizes for the...Ch. 7 - The portable, pressurized fuel can shown in Fig....Ch. 7 - Professor Crocker is building a cabin on a...Ch. 7 - If Professor Crocker's pump, described in Problem...Ch. 7 - The test setup in Fig. 7.39 measures the pressure...Ch. 7 - If the fluid motor in Problem 7.44 has an...Ch. 7 - A village with a need for a simple irrigation...Ch. 7 - As a member of a development team for a new jet...Ch. 7 - A fire truck utilizes its engine to drive a pump...Ch. 7 - A home has a sump pump to handle ground water from...Ch. 7 - In Problem 6.107 an initial calculation was made...Ch. 7 - A creek runs through a certain part of a campus...Ch. 7 - A hot tub is to have 40 outlets that are each 8 mm...Ch. 7 - A large chipper/shredder is to be designed for use...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A pump is driven by an electric motor moves 35 gal/min of water from reservoir A to reservoir B, lifting the water to a total head of 245 ft. The efficiency of the pump and motor are 64% and 84% respectively. What size of motor (HP) is required? a. 3 hp b. 5 hp c. 4 hp d. 7 hparrow_forwardTheoretical horsepower required to pump water at 100 GPM from a larger reservoir to the surface of another reservoir 400 feet higher is?arrow_forwardASAP A centrifugal pump that is used in pumping water to a tank operates at a rate of 1 gpm. The pump is driven directly by an electric motor with an input power of 1.5 hp running at a speed of 1700 rpm. The total head loss of the system is 10 m. If the motor drives the pump at 2200 rpm, what is the rate of flow of the pump?arrow_forward
- A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb, Calculate the horsepower required to do the pumping. The pump and its motor have an overall efficiency of 55 %. i. Determine the velocity of the water at point 2 in ft/s. ii. Assuming that the large open reservoir is open to the atmosphere as well, which of the following equations best describes the mechanical energy balance for the system? iii.The Reynolds number for the flow is?arrow_forwardA pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb, Calculate the horsepower required to do the pumping. The pump and its motor have an overall efficiency of 55 %. i. What is Delta Z (Z2 - Z1) ? in ft. ii. Determine the theoretical shaft work required in foot-pound force per pound mass.. iii.Determine the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s.arrow_forwardA 10-hectare rice land is to be irrigated at the peak water requirement of 10 mm/day. The source of water is pump from a river with outlet discharge directly to the irrigation canal. If the pump operates at 10 hours per day, what should be the capacity of the pump? What should be the size of engine if the total dynamic head is 10 meters. Assume pump efficiency to be 80 percent and engine to be 75 percent.arrow_forward
- A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.arrow_forwardA water pump develops a total head of 200 feet. The pump efficiency is 80% and the motor efficiency is 87.5%. If the power rate is 1.5 cents per kWh, what is the power cost for pumping 100 gal/hr?A. 34 cents per hourB. 1.34 cents per hourC. 2.34 cents per hourD. 3.34 cents per hourarrow_forwardIn oasis Water Company to purify the water, it is flowing through a reducer in a horizontal pipe where the diameter is reduced from 35 cm to 25 cm. The pressure in the 35 cm pipe just upstream of the reducer is 3 150 kPa. The fluid has a vapor pressure of 50 kPa and a specific weight of 5 kN/m . Neglecting frictional effects, calculate flow rate of water through this pipe in lit/s. Draw diagram neatly.arrow_forward
- A water pump develops a total head of 200 ft. The pump efficiency is 80% and the motor efficiency is 87.5%. If the power rate is 1.5 cents per kw-hr, what is the power cost for pumping 1000 gal/hr?arrow_forwardA system requires delivery of water at 40 l/s at a head of 12 ft. An axial pump is available. What rotational speed do you recommend running the pump at?arrow_forwardA large container filled with water and uncovered for use in fighting fires in an ethylene production plant. Water from this tank is pumped into the nozzle when needed use. This fire suppression system is designed to be able to transmit 1890 L/min of water at a pressure of 15 bar (relative pressure). If we ignore the difference in height between the water level in the tank and pump, there is no change in diameter of pipe and nozzle, pump efficiency is 70%. Ask how much work (hp) is required to the pump to achieve the desired pressure and flow would like?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license