Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Question
Chapter 7, Problem 7.89P
To determine
The value at which other conditions remain constant.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
If I noticed copied solution I will give dislike.
In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C is spaced 40 mm from the absorber plate at an average temperature of 75°C. Estimate the convection heat loss coefficient from the absorber plate to the glass when the collector is positioned horizontally. What is the convection heat loss coefficient if the spacing reduced to 10 mm?
In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C is spaced 40 mm from the absorber plate at an average temperature of 75°C. Estimate the convection heat loss coefficient from the absorber plate to the glass when the collector is positioned horizontally. What is the convection heat loss coefficient if the spacing reduced to 10 mm?
FUNDAMENTALS OF CONVECTION
Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s.
What is the minimum length of the plate necessary for the Reynolds number to reach 2x107?
If the critical Reynolds number is 5x105, what type of flow regime would the airflow experience at 0.2 m from the leading edge?
Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject
Chapter 7 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 7 - Consider the following fluids at a film...Ch. 7 - Engine oil at 100C and a velocity of 0.1 m/s flows...Ch. 7 - Consider steady, parallel flow of atmospheric air...Ch. 7 - Consider a liquid metal (Pr1), with free stream...Ch. 7 - Consider the velocity boundary layer profile for...Ch. 7 - Consider a steady, turbulent boundary layer on and...Ch. 7 - Consider flow over a flat plate for which it is...Ch. 7 - A flat plate of width 1 m is maintained at a...Ch. 7 - An electric air heater consists of a horizontal...Ch. 7 - Consider atmospheric air at 25C and a velocity of...
Ch. 7 - Repeat Problem 7.11 for the case when the boundary...Ch. 7 - Consider water at 27°C in parallel flow over an...Ch. 7 - Explain under what conditions the total rate of...Ch. 7 - In fuel cell stacks, it is desirable to operate...Ch. 7 - The roof of a refrigerated truck compartment is of...Ch. 7 - The top surface of a heated compartment consists...Ch. 7 - Calculate the value of the average heat transfer...Ch. 7 - The proposed design for an anemometer to determine...Ch. 7 - Steel (AISI 1010) plates of thickness =6mm and...Ch. 7 - Consider a rectangular fin that is used to cool a...Ch. 7 - The Weather Channel reports that it is a hot,...Ch. 7 - In the production of sheet metals or plastics, it...Ch. 7 - An array of electronic chips is mounted within a...Ch. 7 - A steel strip emerges from the hot roll section of...Ch. 7 - In Problem 7.23. an anemometer design was...Ch. 7 - One hundred electrical components, each...Ch. 7 - The boundary layer associated with parallel flow...Ch. 7 - Forced air at 250C and 10 m/s is used to cool...Ch. 7 - Air at atmospheric pressure and a temperature of...Ch. 7 - Consider a thin, 50mm50mm fuel cell similar to...Ch. 7 - The cover plate of a flat-plate solar collector is...Ch. 7 - An array of 10 silicon chips, each of length...Ch. 7 - A square (10mm10mm) silicon chip is insulated on...Ch. 7 - A circular pipe of 25-mm outside diameter is...Ch. 7 - An L=1-m- long vertical copper tube of inner...Ch. 7 - A long, cylindrical, electrical heating element of...Ch. 7 - Consider the conditions of Problem 7.49, but now...Ch. 7 - Pin fins are to be specified for use in an...Ch. 7 - Prob. 7.52PCh. 7 - Prob. 7.53PCh. 7 - Hot water at 500C is routed from one building in...Ch. 7 - In a manufacturing process, long aluminum rods of...Ch. 7 - Prob. 7.58PCh. 7 - To determine air velocity changes, it is proposed...Ch. 7 - Determine the convection heat loss from both the...Ch. 7 - Prob. 7.63PCh. 7 - Prob. 7.64PCh. 7 - Prob. 7.67PCh. 7 - A thermocouple is inserted into a hot air duct to...Ch. 7 - Consider a sphere with a diameter of 20 mm and a...Ch. 7 - Prob. 7.76PCh. 7 - A spherical, underwater instrument pod used to...Ch. 7 - Worldwide. over a billion solder balls must be...Ch. 7 - Prob. 7.80PCh. 7 - Prob. 7.81PCh. 7 - Consider the plasma spray coating process of...Ch. 7 - Prob. 7.83PCh. 7 - Tissue engineering involves the development of...Ch. 7 - Consider temperature measurement in a gas stream...Ch. 7 - Prob. 7.89PCh. 7 - A preheater involves the use of condensing steam...Ch. 7 - Prob. 7.91PCh. 7 - A tube bank uses an aligned arrangement of...Ch. 7 - A tube bank uses an aligned arrangement of...Ch. 7 - Repeat Problem 7.94, but with NL=7,NT=10, and...Ch. 7 - Heating and cooling with miniature impinging jets...Ch. 7 - A circular transistor of 10-mm diameter is cooled...Ch. 7 - A long rectangular plate of AISI 304 stainless...Ch. 7 - A cryogenic probe is used to treat cancerous skin...Ch. 7 - Prob. 7.103PCh. 7 - Prob. 7.104PCh. 7 - Prob. 7.105PCh. 7 - Consider the packed bed of aluminum spheres...Ch. 7 - Prob. 7.108PCh. 7 - Prob. 7.109PCh. 7 - Prob. 7.111PCh. 7 - Packed beds of spherical panicles can be sintered...Ch. 7 - Prob. 7.114PCh. 7 - Prob. 7.116PCh. 7 - Prob. 7.117PCh. 7 - Prob. 7.118PCh. 7 - Prob. 7.119PCh. 7 - Prob. 7.120PCh. 7 - Dry air at 35°C and a velocity of 20 m/s flows...Ch. 7 - Prob. 7.123PCh. 7 - Benzene, a known carcinogen, has been spilled on...Ch. 7 - Prob. 7.125PCh. 7 - Prob. 7.126PCh. 7 - Condenser cooling water for a power plant is...Ch. 7 - Prob. 7.128PCh. 7 - In a paper-drying process, the paper moves on a...Ch. 7 - Prob. 7.131PCh. 7 - Prob. 7.132PCh. 7 - Prob. 7.133PCh. 7 - Prob. 7.134PCh. 7 - Prob. 7.136PCh. 7 - It has been suggested that heat transfer from a...Ch. 7 - Prob. 7.138PCh. 7 - Cylindrical dry-bulb and wet-bulb thermometers are...Ch. 7 - The thermal pollution problem is associated with...Ch. 7 - Cranberries are harvested by flooding the bogs in...Ch. 7 - A spherical drop of water, 0.5 mm in diameter, is...Ch. 7 - Prob. 7.143PCh. 7 - Prob. 7.144PCh. 7 - Prob. 7.145PCh. 7 - Prob. 7.146PCh. 7 - Prob. 7.147PCh. 7 - Consider an air-conditioning system composed of a...Ch. 7 - Prob. 7.149P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 5.43 A refrigeration truck is traveling at 130 km/h on a desert highway where the air temperature is . The body of the truck is idealized as a rectangular box 3 m wide, 2.1 m high, and 6 m long, at a surface temperature . Assume that (1) the heat transfer from the front and back of the truck is neglected, (2) the stream does not separate from the surface, and (3) the boundary layer is turbulent over the whole surface. Calculate the required cooling rate of the refrigeration unit.arrow_forwardTo maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe ( ks = 40 W/m·K) has an inside diameter of Di,1 = 150 mm and wall thickness ti = 20 mm while the outer steel pipe has an inside diameter of Di,1 = 250 mm and wall thickness . Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation ( kp = 0.0425 W/m·K) provides an external convection heat transfer coefficient of ho = 500 W/m2·K. The convection coefficient associated with the flowing crude oil is hi = 450 W/m2·K. (2) It is proposed to enhance the performance of the pipe-in-pipe device by replacing a thin ( ta =10 mm) section of polyurethane located at the outside of the inner pipe with an…arrow_forwardTo maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (ks= 40 W/m·K) has an inside diameter of Di, 1= 150 mm and wall thickness ti= 20 mm while the outer steel pipe has an inside diameter of Di, 2= 250 mm and wall thickness to=ti. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (kp= 0.0675 W/m·K) between the two pipes does not exceed its maximum service temperature of Tp, max= 70°C. The ocean water is at ∞ T∞, o= -5°C and provides an external convection heat transfer coefficient of ho= 500 W/m2·K. The convection coefficient associated with the flowing crude oil is hi= 450 W/m2·K. (2) It is proposed to enhance the performance of the…arrow_forward
- To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (ks= 40 W/m·K) has an inside diameter of Di, 1= 150 mm and wall thickness ti= 20 mm while the outer steel pipe has an inside diameter of Di, 2= 250 mm and wall thickness to=ti. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (kp= 0.0675 W/m·K) between the two pipes does not exceed its maximum service temperature of Tp, max= 70°C. The ocean water is at ∞ T∞, o= -5°C and provides an external convection heat transfer coefficient of ho= 500 W/m2·K. The convection coefficient associated with the flowing crude oil is hi= 450 W/m2·K. (2) It is proposed to enhance the performance of the…arrow_forwardCalculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm outside diameter, 0.9 m long. The pipe surface temperature is 145 ° C, and the air temperature is 40 ° C. Convection coefficient = ... W / m² ° C.arrow_forwardWrite the expression for critical radius of insulation for a cylindrical pipe. Consider aninsulated pipe exposed to the atmosphere. Will the critical radius of insulation begreater on calm days or on windy days? Why?arrow_forward
- A 0.407m long vertical steel plate at a surface temperature of 700K is in contact with hot air at 237K, latm absolute pressure. If E=0.81 for steel pipe:a. Calculate the total 1S1 transfer coefficient for the convection increase 1 convectionb. What is the heat loss per unit area of the surface?arrow_forwardA horizontal copper plate 10 cm thick is initially uniform in temperature at 250◦C.The bottom surface of the plate is insulated. The top surface is suddenly exposed toa fluid stream at 80◦C. After 6 min the surface temperature has dropped to 150◦C.Calculate the convection heat-transfer coefficient that causes this drop.arrow_forwardA plastics plant manufactures larges pieces of plastic by continuously extruding thin sheets.As the sheets flow out of the extruder, they are cooled via forced convection and radiation.The plastic sheets are 1 mm thick, 1 m wide, and leave the extruder at a rate of 9 m/min.A fan blows air over the top and bottom surface of the sheet during the first meter after thesheet leaves the extruder. The fan accelerates the air to 3 m/s and the air is known to be at27°C at the fan outlet. At the exit of the extruder, the plastic is at 90°C. The plastic isestimated to have an emissivity of ? = 0.9 and the general surroundings are at 20°C. A) Determine the rate of heat transfer via convection and radiation from the 1-m-longsection of the plastic sheet that is being force cooled. take the surface temperature to be 90°C overthe entire section of interest. B) The density-specific heat product of the plastic is ?? = 1920 kJ m3– K⁄ . What is thetemperature of the plastic at the end of the cooling…arrow_forward
- The outer diameter of a pipe is 25 mm and its surface temperature is 90 ° C. Air at a temperature of 30 ° C flows diagonally over the pipe at 15 m / s. What is the resistance force per unit length of the pipe? What is the heat transfer from the unit length of the pipe?arrow_forwardConsider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? I need the solution from fundamental concepts of how the heat flow behaves in the systemarrow_forwardQi/ An Aluminum flat plate has a continuous and smooth surface over which the air flows at 2 m/s. The plate consists of 25 part that each part is 10 mm long with 0.2 m width. During operation, each part is maintained at 500°C and the air is at 25°C. What is the rate of convection heat transfer from the first part? The sixth part? All the plate?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license