A student prepared a calibration plot for a series of iron(II)-1,10-phenanthroline complex standards. On the x axis is Fe concentration in ppm. On the y axis is the absorbance (M). The plot's equation is y = 0.2471x + 0.006 What is the ppm absorptivity of this solution if the pathlength of light is 1 cm?

A student prepared a calibration plot for a series of iron(II)-1,10-phenanthroline complex standards. On the x axis is Fe concentration in ppm. On the y axis is the absorbance (M). The plot's equation is y = 0.2471x + 0.006 What is the ppm absorptivity of this solution if the pathlength of light is 1 cm?

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter8: Bonding In Transition Metal Compounds And Coordination Complexes

Section: Chapter Questions

Problem 36P

See similar textbooks

Similar questions

The accompanying data (1.00-cm cells) were obtained for the spectrophotometric titration 10.00 mL of Pd(II) with 2.44 10-4 M Nitroso R(O. W Rollins and M. M. Oldham, Anal. chem .,1971, 43, 262, DOI: 10.1021/ac60297a026). Calculate the concentration of the Pd(II) solution, given that the ligand-to-cation ratio in the colored product is 2:1
A metal complex with a Molecular mass of 820 g mol−1 was dissolved and the solution made up to 25 mL in a volumetric flask. 1 mL was withdrawn, placed in a 100 mL volumetric flask and diluted to the mark. The absorbance (at 457 nm) of this solution (in a 1 cm cuvette) was 0.245. The extinction coefficient for this compound at 457 nm (ε530) = 11715 M-1cm-1.(a) calculate the concentration of the compound in the cuvette.(b) calculate the concentration of the compound in the 25mL volumetric flask(c) determine the mass of compound used to make the 25mL solution
The absorbance values observed during the determination of the complex stoichiometry with the Job method using the spectroscopic method were plotted and the following correct equations were obtained. According to this, what is the n value of the compound formed by Fe + 3 and SCN- ions?1. Line equation: y = 2.6188x + 0.1608 2. Line equation: y = -2.5963x + 2.7203
The absorbance values observed during the determination of the complex stoichiometry with the Job method using the spectroscopic method were plotted and the following correct equations were obtained. What is the n value of the compound formed by Fe + 3 and SCN- ions? 1. Line equation: y = 2.6188x + 0.16082. Line equation: y = -2.5963x + 2.7203
A standard solution was put through appropriate dilutions to give the concentrations of iron shown in the table that follows. The iron(II)-1,10-phenanthroline complex was then formed in 25.0-mL aliquots of these solutions, following which each was diluted to 50.0 mL. The following absorbances (1.00-cm cells) were recorded at 510 nm: Calculate the concentration, in ppm, of a sample with an abosrbance of 0.829. Fe(II) concentration (ppm) A510 4.00 0.160 10.0 0.390 16.0 0.630 24.0 0.950 32.0 1.260 40.0 1.580
An absorbance versus concentration data for the thiocyanatoiron(III) complex at 510 nm and makes a Beer's law plot.Based on the plot, what [Fe(SCN)2+] would the student report for a solution that has an absorbance of 0.300 at 510 nm? Also select all below closely matches the procedures to be followed in this experiment and why they are being carried out. 1) A Beer's law plot will be used as a means to determine the equilibrium concentration of the thiocyanatoiron(III) complex. 2)A Beer's law plot will be used to confirm known values of the equilibrium constant for the formation of the thiocyanatoiron(III) complex. 3)To make the Beer's law calibration graph, the formation equilibrium for the thiocyanatoiron(III) complex will be flooded with a large excess of thiocyanate ion. 4)To make the Beer's law calibration graph, the formation equilibrium for the thiocyanatoiron(III) complex will be flooded with a large excess of iron(III) ion.
. A student collects the following data for the absorbance of a complex measured in 1.00 cmspectrophotometric cells. The molar absorptivity (ε) of the complex under investigation is 2.25×103L/mol·cm. Calculate the concentration of the complex in solution at each time of the reaction.Time (min)MeasuredAbsorbanceComplex Concentration(M)0.000 1.50010.000 1.31320.000 1.12530.000 0.93840.000 0.750
The absorbance values observed during the determination of the complex stoichiometry with the Job method using the spectroscopic method were plotted and the following correct equations were obtained. What is the n value of the compound formed by Fe + 3 and SCN- ions? 1. Line equation: y = 2.6188x + 0.1608 2. Line equation: y = -2.5963x + 2.7203 a) 1 b) 3 c) 0.5 d) 2 e) 5
Absorbance measurements were taken on a series of Fe standards complexed with 1,10-phenanthroline. A plot of absorbance vs. concentration yielded a linear curve with the equation y=1.008e03x + 0.0395 (where y is the absorbance and x represents the Fe concentration in moles/L). Using this information calculate the Fe concentration (in ppm) in a 40.0-mL aliquot of ground water that produced an absorbance of 0.580.
EDTA abstracts bismuth(III) from its thiourea complex:Bi1tu2631 1 H2Y22 S BiY2 1 6tu 1 2H1where tu is the thiourea molecule (NH2)2CS. Predict the shape of a photometric titration curve based on thisprocess, given that the Bi(III) or thiourea complex is the only species in the system that absorbs light at 465nm, the wavelength selected for the analysis.
The molar absorptivity for the complex formed between bismuth(III) and thiourea is 9.32x103 L cm-1 mol-1 at 470 nm. Calculate the concentration (in mol/L) of the complex if the absorbance is 0.845 measured with a 1.00 cm cell.
A FeSCN complex, whose maximum absorbance is at a λ of 580 nm, has a molar extinction coefficient of 5×103 M-1cm-1 . A solution is measured with a 25 mm cell at the same λ , obtaining 20.6% T. Calculate the concentration in [ppm] of the complex in the solution.