Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 10, Problem 22P
Data measured during tests of a centrifugal pump driven at 3000 rpm are
The flow rate is 65 gpm and the torque applied to the pump shaft is 4.75 lbf ft. The pump efficiency is 75 percent, and the electric motor efficiency is 85 percent. Find (a) the electric power required and (b) the gage pressure at section 2
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.
A plant has installed a single suction centrifugal pump with a discharge of 68 m3/hr under 60 m head and running at 1200 rpm. It is proposed to install another pump with double suction but of the same type to operate at 37.22 m head and deliver 90 m3/hr. Determine the speed of the new pump.
and what should be the new impeller diameter if the diameter of the original pump is 140mm?
A centrifugal pump with a 735 mm diameter impeller runs at 1979 rpm. The water enters without whirl, and α2 = 30ª. The actual head produced by the pump is 17 m. Find the hydraulic efficiency when V2 = 6.7. Express your answer in decimals.
Chapter 10 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 10 - The geometry of a centrifugal water pump is r1 =...Ch. 10 - Find the resulting -groups when (a) D, , and Q or...Ch. 10 - Consider the centrifugal pump impeller dimensions...Ch. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - The blade is one of a series. Calculate the force...Ch. 10 - This blade is one of a series. What force is...Ch. 10 - A centrifugal water pump, with 15-cm-diameter...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - A series of blades, such as in Example 10.13,...
Ch. 10 - In passing through this blade system, the absolute...Ch. 10 - A centrifugal pump runs at 1750 rpm while pumping...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - Kerosene is pumped by a centrifugal pump. When the...Ch. 10 - In the water pump of Problem 10.8, the pump casing...Ch. 10 - Use data from Appendix C to choose points from the...Ch. 10 - Data from tests of a water suction pump operated...Ch. 10 - A centrifugal pump impeller having r1 = 50 mm, r2...Ch. 10 - A centrifugal pump impeller having dimensions and...Ch. 10 - An axial-flow fan operates in sea-level air at...Ch. 10 - Data measured during tests of a centrifugal pump...Ch. 10 - A small centrifugal pump, when tested at N = 2875...Ch. 10 - If the impeller of Problem 10.20 rotates between...Ch. 10 - At the outlet of a pump impeller of diameter 0.6 m...Ch. 10 - Typical performance curves for a centrifugal pump,...Ch. 10 - A pump with D = 500 mm delivers Q = 0.725 m3/s of...Ch. 10 - At its best efficiency point ( = 0.87), a...Ch. 10 - Using the performance curves in Appendix C, select...Ch. 10 - A pumping system must be specified for a lift...Ch. 10 - A centrifugal water pump operates at 1750 rpm; the...Ch. 10 - A set of eight 30-kW motor-pump units is used to...Ch. 10 - A blower has a rotor with 12-in. outside diameter...Ch. 10 - A centrifugal water pump has an impeller with an...Ch. 10 - Appendix C contains area bound curves for pump...Ch. 10 - Use data from Appendix C to verify the similarity...Ch. 10 - A centrifugal water pump has an impeller with...Ch. 10 - Catalog data for a centrifugal water pump at...Ch. 10 - A 1/3 scale model of a centrifugal water pump...Ch. 10 - Sometimes the variation of water viscosity with...Ch. 10 - A large deep fryer at a snack-food plant contains...Ch. 10 - Data from tests of a pump, with a...Ch. 10 - A four-stage boiler feed pump has suction and...Ch. 10 - A centrifugal pump operating at N = 2265 rpm lifts...Ch. 10 - A centrifugal pump is installed in a piping system...Ch. 10 - Part of the water supply for the South Rim of...Ch. 10 - Consider the flow system shown in Problem 8.94....Ch. 10 - Afire nozzle is supplied through 300 ft of...Ch. 10 - Performance data for a centrifugal fan of 3-ft...Ch. 10 - The performance data of Problem 10.57 are for a...Ch. 10 - Experimental test data for an aircraft engine fuel...Ch. 10 - Preliminary calculations for a hydroelectric power...Ch. 10 - Conditions at the inlet to the nozzle of a Pelton...Ch. 10 - A Francis turbine is to operate under a head of 46...Ch. 10 - A Kaplan (propeller with variable-pitch blades)...Ch. 10 - Francis turbine Units 19, 20, and 21, installed at...Ch. 10 - Measured data for performance of the reaction...Ch. 10 - For a flow rate of 12 L/s and turbine speed of 65...Ch. 10 - The velocity of the water jet driving this impulse...Ch. 10 - An impulse turbine is to develop 15 MW from a...Ch. 10 - An impulse turbine under a net head of 33 ft was...Ch. 10 - The absolute velocities and directions of the jets...Ch. 10 - A fanboat in the Florida Everglades is powered by...Ch. 10 - A jet-propelled aircraft traveling at 225 m/s...Ch. 10 - When an air jet of 1-in.-diameter strikes a series...Ch. 10 - The volume flow rate through the propeller of an...Ch. 10 - A typical American multi blade farm windmill has D...Ch. 10 - An airplane flies at 200 km/h through still air of...Ch. 10 - This ducted propeller unit drives a ship through...Ch. 10 - A model of an American multi blade farm windmill...Ch. 10 - A large Darrieus vertical axis wind turbine was...Ch. 10 - Show that this ducted propeller system when moving...Ch. 10 - This ducted propeller unit (now operating as a...Ch. 10 - What is the maximum power that can be expected...Ch. 10 - If an ideal windmill is operating at best...Ch. 10 - A prototype air compressor with a compression...Ch. 10 - Prob. 89PCh. 10 - We have seen many examples in Chapter 7 of...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The two identical boards are bolted together to form the beam. Determine the maximum spacing s of the bolts to ...
Statics and Mechanics of Materials (5th Edition)
A piston/cylinder arrangement with a linear spring similar to Fig. P3.33 contains R-134a at 15C,x=0.4 and a vol...
Fundamentals Of Thermodynamics
If the rpm for a facing cut (assuming given work and tool materials) is being held constant, what is happening ...
Degarmo's Materials And Processes In Manufacturing
42. A container holding 1.5 moles [mol] of oxygen (formula: O2, molecular weight = 32 grams per mole [g/mol]) a...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
The force F is applied at the end of arm ACD, which is mounted to a vertical post. Replace this single force F ...
Engineering Mechanics: Statics
Why is it possible for the fusion zone to have a chemistry that is different from the filler metal?
DeGarmo's Materials and Processes in Manufacturing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- For a centrifugal pump of impeller diameter D rotating at N to develop a head of H and discharge Q, what would be the new head developed by the same pump if we halve the impeller speed to N/2? H/A 2H H 4H H/2arrow_forward4. A centrifugal pump has r2 = 9 in., b2 = 2 in., and 2 = 35 and rotates at 1060 rev/min. If it generates a head of 180 ft, determine the theoretical (a) flow rate, in gpm; and (b) horsepower. Assume near-radial entry flow. a. flow rate Answer : _______________ gpmb. water horsepower Answer : _______________ HParrow_forwardIf a pump with a manometric head of 12 m is designed to deliver a flow rate of 7500 liters / minute. Since the rotation speed of the pump shaft is 1800 rpm, what is the dimensionless pump specific speed of this pump?arrow_forward
- A pump is required to deliver 120000 lpm of water at a head of 25 m. A motor which spins at 450 rpm is available. What kind of pump geometry should be used? Estimate the power requirement of this pump.arrow_forward3) The MITL ME laboratory has installed a double-suction, three-stage, centrifugal pump with a discharge of 330 gpm under 200 ft head and running at 1200 rpm. It is proposed to install another pump with double suction and six stages, but of the same characteristics, to operate at 98 ft head and deliver 430 gpm. Calculate a) the speed of the proposed pump; b) the impeller diameter of the proposed pump if the diameter of the existing pump is 6 inches; and c) the type of the existing and the proposed pump.arrow_forwardA centrifugal pump delivers 0.071 m3/s of water against a head of 7.6-m at 1450 rpm and requires 6.7 kW. If the speed is reduced to 1200 rpm calculate the power , assuming the same efficiency.arrow_forward
- Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid against a head of 25 m. The diameter of the impellers being 24 cm and the speed of 1800 rpm. A pump is to be made up with a number of stages in series of similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloliters/min against a totalhead of 250 m. Find the diameter of the impellers and the number of stages required in this case. Answer: D = 46.63 cm, n = 6 stagesarrow_forwardFor each statement about centrifugal pumps, choose whether the statement is true or false, and discuss your answer briefly: (a) A centrifugal pump with radial blades has higher efficiency than the same pump with backward-inclined blades. (b) A centrifugal pump with radial blades produces a larger pressure rise than the same pump with backward- or forwardinclined blades over a wide ange of V. . (c) A centrifugal pump with forward-inclined blades is a good choice when one needs to provide a large pressure rise over a wide range of volume flow rates. (d) A centrifugal pump with forward-nclined blades would most likely have less blades than a pump of the same size with backward-inclined or radial blades.arrow_forwardA pump is designed to deliver 9500 L/min of water at a required head of 8 m. The pump shaft rotates at 1100 rpm. The pump specific speed in nondimensional form is (a) 0.277 (b) 0.515 (c) 1.17 (d ) 1.42 (e) 1.88arrow_forward
- A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. After resolving the turbine speed, what horsepower would be developed under a head of 11 meters?arrow_forwardSeven hundred gallons per minute of water are being discharged by a centrifugal pump 5 ft above the pump inlet. The inlet pressure is 4-in Hg above the atmospheric and the discharge pressure is 29 psia. If the pump has an 8-in diameter inlet and a 4-in diameter discharge, find the new flowrate if thr pump speed is doubled. Assume the pump input is 8Hp. A. 700 gpmB. 1050 gpmC. 1400 gpmD. 1750 gpmarrow_forwardA 1750 rpm centrifugal pump equipped with an 11-in.-diameter impeller requires 14.3 bhp when delivering 300 gpm at a head of 111 ft. Predict the new capacity, head, and power required when the impeller diameter is increased to 13 in.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license