Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
thumb_up100%
Chapter 2, Problem 2.54P
The one-dimensional system of mass M with constant properties and no internal heat generation shown in the figure is initially at a uniform temperature
- Write the differential equation, and identify the boundary and initial conditions that could be used to determine the temperature as a function of position and time in the system.
- On
- On
- After a period of time has elapsed, the heater power is switched off. Assuming that the insulation is perfect. the system will eventually reach a final uniform temperature
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A curved surface of a rod of length L is perfectly insulated against the flow of heat . The rod , which is so thin that heat flow in it can be assumed to be one dimensional , is initially at the temperature U(x,0 ) = 20 x / 3L ° C . Find the temperature at any point in the road at any subsequent time if at t = 0 the temperature at each end of the rod is suddenly reduced to 0 ° C and maintained at that temperature thereafter .
A thick-walled cylindrical tubing of hard rubber (k=0.151 W/m*K) having an inside radius of 5 mm and an outside radius of 20 mm is being used as a temporary cooling coil in a bath. Ice water is flowing rapidly inside, and the inside wall temperature is 275 K. The outside surface temperature is 300 K. A total of 20 W must be removed from the bath by the cooling coil. How many meter of tubing are needed?
A spherical container having an outer radius r2 and inner radius r1 (with thermal conductivity, k) is filled with radioactive material generating constant heat at a rate of qdot. Fluid flows across the container at Tinfinity and convection coefficient h. Obtain a relation for the variation of temperature through the spherical container assuming steady state.
Chapter 2 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r, has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - A young engineer is asked to design a thermal...Ch. 2 - A one-dimensional plane wall of thickness 2L=100mm...
Ch. 2 - Consider steady-state conditions for...Ch. 2 - Consider a plane wall 100 mm thick and of thermal...Ch. 2 - A cylinder of radius ro, length L, and thermal...Ch. 2 - In the two-dimensional body illustrated, the...Ch. 2 - Consider the geometry of Problem 2.14 for the case...Ch. 2 - Steady-state, one-dimensional conduction occurs in...Ch. 2 - An apparatus for measuring thermal conductivity...Ch. 2 - An engineer desires to measure the thermal...Ch. 2 - Consider a 300mm300mm window in an aircraft. For a...Ch. 2 - Consider a small but known volume of metal that...Ch. 2 - Use INT to perform the following tasks. Graph the...Ch. 2 - Calculate the thermal conductivity of air,...Ch. 2 - A method for determining the thermal conductivity...Ch. 2 - Compare and contrast the heat capacity cp of...Ch. 2 - A cylindrical rod of stainless steel is insulated...Ch. 2 - At a given instant of time, the temperature...Ch. 2 - A pan is used to boil water by placing it on a...Ch. 2 - Uniform internal heat generation at q=5107W/m3 is...Ch. 2 - Consider a one-dimensional plane wall with...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - The temperature distribution across a wall 0.3 m...Ch. 2 - Prob. 2.33PCh. 2 - One-dimensional, steady-state conduction with...Ch. 2 - Derive the heat diffusion equation, Equation 2.26,...Ch. 2 - Derive the heat diffusion equation, Equation 2.29....Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - Prob. 2.41PCh. 2 - Prob. 2.42PCh. 2 - cylindrical system illustrated has negligible...Ch. 2 - Beginning with a differential control volume in...Ch. 2 - Prob. 2.45PCh. 2 - Prob. 2.46PCh. 2 - For a long circular tube of inner and outer radii...Ch. 2 - Passage of an electric current through a long...Ch. 2 - Two-dimensional. steady-state conduction occurs in...Ch. 2 - An electric cable of radius r1 and thermal...Ch. 2 - A spherical shell of inner and outer radii ri and...Ch. 2 - A chemically reacting mixture is stored in a...Ch. 2 - A thin electrical heater dissipating 4000W/m2 is...Ch. 2 - The one-dimensional system of mass M with constant...Ch. 2 - Consider a one-dimensional plane wall of thickness...Ch. 2 - A large plate of thickness 2L is at a uniform...Ch. 2 - The plane wall with constant properties and no...Ch. 2 - Consider the steady-state temperature...Ch. 2 - A plane wall has constant properties, no internal...Ch. 2 - A plane wall with constant properties is initially...Ch. 2 - Consider the conditions associated with Problem...Ch. 2 - Consider the steady-state temperature distribution...Ch. 2 - A spherical particle of radius r1 experiences...Ch. 2 - Prob. 2.64PCh. 2 - A plane wall of thickness L=0.1m experiences...Ch. 2 - Prob. 2.66PCh. 2 - A composite one-dimensional plane wall is of...Ch. 2 - Typically, air is heated in a hair dryer by...Ch. 2 - Prob. 2.69P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6arrow_forward5.43 A refrigeration truck is traveling at 130 km/h on a desert highway where the air temperature is . The body of the truck is idealized as a rectangular box 3 m wide, 2.1 m high, and 6 m long, at a surface temperature . Assume that (1) the heat transfer from the front and back of the truck is neglected, (2) the stream does not separate from the surface, and (3) the boundary layer is turbulent over the whole surface. Calculate the required cooling rate of the refrigeration unit.arrow_forwardThe heat flow within a building is increasing or decreasing exponentially E to power 3t in line withtemperature difference which is t degrees ( C) with the outside surroundings.Estimate and explore the growth rate graphically when the temperature difference changes from -20degrees to + 20 degrees (C)arrow_forward
- A spherical, stainless steel (AISI 302) canister is used to store reacting chemicals that provide for a uniform heat flux qi'' to its inner surface. The canister is suddenly submerged in a liquid bath of temperature Tambient < Ti, where Ti is the initial temperature of the canister wall. (a) Assuming negligible temperature gradients in the canister wall and a constant heat flux qi'', develop an equation that governs the variation of the wall temperature with time during the transient process. What is the initial rate of change of the wall temperature if qi'' = 105 W/m^2? (b) What is the steady-state temperature of the wall? (c) Determine the wall temperature as a function of time.arrow_forwardHab. Tiruneh, [4/2/2023 1:23 AM]A solar flux q ^ * falls on a unit length of a very thin tube of diameter d. Inside the tube is a stationary water with initial temperature T_{i} (same as ambient and no gradient inside at any time) and absorbs some of the heat while the rest leaves by convection from the surface to the ambient at T_{m} Develop an equation that can help to determine the temperature of the water at any time. Plot the temperature of the water against time. For a long elapsed time what will be the temperature? To simplify the analysis use theta = T*T_{e} * d*theta = dT theta_{i} = T_{i}*T_{o} (initial condition. Hab. Tiruneh, [4/2/2023 11:53 AM]A flat wall is exposed to an environmental temperature of 38°C. The wall is covered with a layer of insulation 2.5 cm thick whose thermal conductivity is 1.4W / (m ^2 *` C and the temperature of the wall on the inside of the insulation is 315°C. The wall loses heat to the environment by convection. Compute the value of the convection…arrow_forwardHeat Transfer Lesson The water will be heated from 10 (Degrees centigrade oC) to 90 (Degrees centigrade oC) while flowing through a smooth pipe with 1.5 cm inner diameter and 7 meters length.The entire surface of the pipe is equipped with an electric heater, which ensures uniform heating throughout.The outer surface of the heater is well insulated and therefore all heat generated in the heater in continuous operation is transferred to the water in the pipe.If the system provides 6 Liter / minute flow rate of hot water. (Thermophysical properties of water at 50 oC:ρ = 988 m3/kg, k= 0.6305 W/m oC, cp=4181 J/kg oC, Pr=3.628, μ= 0.0005471 kg/m.s ) a)Find the power of the resistance heater [W]. b)Calculate the inner surface temperature [oC] of the pipe at the outlet. c)Find the pressure drop [Pa]. d)Find the pump power [W] required to overcome this pressure drop.arrow_forward
- A truncated solid cone is of circular cross section, and its diameter is related to the axial coordinate by an expression of the form D = ax3/2, where a = 2 m−1/2. The sides are well insulated, while the top surface of the cone at x1 is maintained at T1 and the bottom surface at x2 is maintained at T2. Conductivity k = 336 W/m-K (a) Obtain an expression for the temperature distribution T(x). (b) What is the rate of heat transfer across the cone if it is constructed of pure aluminum with x1 = 0.086 m, T1 = 113°C, x2 = 0.270 m, and T2 = 25°C?arrow_forwardA spherical, stainless steel (AISI 302) canister is used to store reacting chemicals that provide for a uniform heat flux q”i to its inner surface. The canister is suddenly submerged in a liquid bath of temperature T∞ i, where Ti is the initial temperature of the canister wall. (a) Assuming negligible temperature gradients in the canister wall and a constant heat flux , develop an equation that governs the variation of the wall temperature with time during the transient process. What is the initial rate of change of the wall temperature if q”I = 105 W/m2? (b) What is the steady-state temperature of the wall? (c) The convection coefficient depends on the velocity associated with fluid flow over the canister and whether the wall temperature is large enough to induce boiling in the liquid. Compute and plot the steady-state temperature as a function of h for the range 100 ≤ h ≤ 10,000 W/m2 ∙ K. Is there a value of h below which operation would be unacceptable?arrow_forwardA 100 mm diameter steam pipe is covered by two layers of lagging (insulation). The inside layer is 40 mm thick and has a thermal conductivity of 0.07 W/m K. The outside layer is 25 mm thick and has a thermal conductivity of 0.1 W/mK. The pipe carries steam at a temperature of 234°C , where the outside temperature of lagging is 24°C. If the steam pipe is 20 m long, determine (a) The heat lost per hour, (b) The interface temperature of lagging. Neglect the resistance of steam pipe as well as the convection resistances.arrow_forward
- Consider the fluid shown in the U-shaped tube of circular section R = 3 cm. This fluid of mass M and volumetric density: Describe simple harmonic oscillations. The harmonic oscillations of the fluid are governed by the differential equation: Figure 4 represents the acceleration as a function of the MAS time of the fluid. NOW ASSUME THAT THERE IS FRICTION OF THE LIQUID WITH THE WALLS OF THE CONTAINER. IN THIS CASE, THE OSCILLATIONS ARE DAMPERED WITH THE PASSAGE OF THE TIMEPO UNTIL THE BALANCE IS REACHED. IF THE AMPLKITUDE OF THE OSCILLATIONS DECAYS BY A FACTOR e ^ (- 6π) IN A TIME OF 2S. WHAT WILL BE THE FREQUENCY OF THE DAMPERED OSCILLATIONS?arrow_forwardA 1.2 m long vertical pipe, with a diameter 0.05 m, carrying a mixture of liquid water and vapor at atmospheric pressure is used to heat a very large liquid water tank, with water temperature maintained at 40 C. Calculate how much is the heat rate transferred from the pipe to the surrounding water at steady-state. (Consider the water in the tank at atmospheric pressure.)arrow_forwardThe class includes 40 people. Heat loss from the walls of the class, including the glass windows, is negligible. A flow of cold air enters the classroom via the main entrance, flows in the classroom, and then leaves through an emergency exit door located at the back of the class. Both the entrance door and the emergency exit door have the same dimensions of 1.2 m length and 1.9 m height. Assuming steady-state heat transfer upon reaching the room temperature at a constant value:(a) If cold air enters the room at 20 °C, the heat generated due to the metabolism of a student/lecturer is 70 W, and air flow rate through both doors is 0.05 m/s, determine the room temperature. Assume that thechanges in properties of air during the increase in room temperature maybe safely ignored.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license