Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 4, Problem 4.92P
Consider the system of Problem 4.54. The interior surface is exposed to hot gases at 3500C with a convection coefficient of
- Using a grid spacing of 75 mm, calculate the temperature field within the system and determine the heat loss per unit length by convection from the outer surface of the flue to the air. Compare this result with the heat gained by convection from the hot gases to the air.
- Determine the effect of grid spacing on the temperature field and heat loss per unit length to the air. Specifically. consider a grid spacing of 25 mm and plot appropriately spaced isotherms on a schematic of the system. Explore the effect of changes in the convection coefficients on the temperature field and heat loss.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Consider a two-layer sphere with inside fluid convection rate h1 and outer rate h2. The first layer has inside radius r1 and outside radius r2. The second layer has outside radius r3. What is the general equation for the total resistance? Neglect thermal contact resistance.
Natural Convection Cooling of an Orange.An orange 102 mm in diameter having a surface temperature of 21.1°C is placed on an open shelf in a refrigerator held at4.4°C. Calculate the heat loss by natural convection, neglecting radiation. As an approximation, the simplified equation for vertical planes can be used withLreplaced by the radius of the sphere (M1). For a more accurate correlation, see (S2).
A furnace wall consists of 200 mm of refractory fireclay brick, 100 mm of kaolin brick, and 6 mm of steel plate. The fire side of the refractory is at 1150°C and the outside of the steel is at 30°C. An accurate heat balance over the furnace shows the heat loss from the wall to be 300 W/m2. It is known that there may be thin layers of air between the layers of brick and steel. To how many millimeters of kaolin are these air layers equivalent? The thermal conductivities of the fireclay brick, the kaolin brick and the steel are 1.7, 0.17, 17, respectively
Chapter 4 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate of...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Using the thermal resistance relations developed...Ch. 4 - Free convection heat transfer is sometimes...Ch. 4 - Consider Problem 4.5 for the case where the plate...Ch. 4 - Prob. 4.9PCh. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Determine the heat transfer rate between two...Ch. 4 - A two-dimensional object is subjected to...Ch. 4 - An electrical heater 100 mm long and 5 mm in...Ch. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - A tube of diameter 50 mm having a surface...Ch. 4 - Pressurized steam at 450K flows through a long,...Ch. 4 - The temperature distribution in laser-irradiated...Ch. 4 - Hot water at 85°C flows through a thin-walled...Ch. 4 - A furnace of cubical shape, with external...Ch. 4 - Laser beams are used to thermally process...Ch. 4 - A double-glazed window consists of two sheets of...Ch. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - A small device is used to measure the surface...Ch. 4 - A cubical glass melting furnace has exterior...Ch. 4 - An aluminum heat sink (k=240W/mK), used to cool an...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - A long constantan wire of 1-mm diameter is butt...Ch. 4 - A hole of diameter D=0.25m is drilled through the...Ch. 4 - In Chapter 3 we that, whenever fins are attached...Ch. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Prob. 4.34PCh. 4 - An electronic device, in the form of a disk 20 mm...Ch. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - One of the strengths of numerical methods is their...Ch. 4 - Determine expressionsfor...Ch. 4 - Consider heat transfer in a one-dimensional...Ch. 4 - In a two-dimensional cylindrical configuration,...Ch. 4 - Upper and lower surfaces of a bus bar are...Ch. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Consider the nodal point 0 located on the boundary...Ch. 4 - Prob. 4.48PCh. 4 - Prob. 4.49PCh. 4 - Consider the network for a two-dimensional system...Ch. 4 - An ancient myth describes how a wooden ship was...Ch. 4 - Consider the square channel shown in the sketch...Ch. 4 - A long conducting rod of rectangular cross section...Ch. 4 - A flue passing hot exhaust gases has a square...Ch. 4 - Steady-state temperatures (K) at three nodal...Ch. 4 - Functionally graded materials are intentionally...Ch. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Consider an aluminum heat sink (k=240W/mK), such...Ch. 4 - Conduction within relatively complex geometries...Ch. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures (°C) associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.63PCh. 4 - Prob. 4.64PCh. 4 - Consider a two-dimensional. straight triangular...Ch. 4 - A common arrangement for heating a large surface...Ch. 4 - A long, solid cylinder of diameter D=25mm is...Ch. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Prob. 4.71PCh. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Refer to the two-dimensional rectangular plate of...Ch. 4 - The shape factor for conduction through the edge...Ch. 4 - Prob. 4.77PCh. 4 - A simplified representation for cooling in very...Ch. 4 - Prob. 4.84PCh. 4 - A long trapezoidal bar is subjected to uniform...Ch. 4 - Consider the system of Problem 4.54. The interior...Ch. 4 - A long furnace. constructed from refractory brick...Ch. 4 - A hot pipe is embedded eccentrically as shown in a...Ch. 4 - A hot liquid flows along a V-groove in a solid...Ch. 4 - Prob. 4S.5PCh. 4 - Hollow prismatic bars fabricated from plain carbon...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1arrow_forward1.11 Calculate the heat loss through a glass window 7-mm thick if the inner surface temperature is 20°C and the outer surface temperature is 17°C. Comment on the possible effect of radiation on your answer.arrow_forwardYou have a steel ball bearing with a diameter of 1.50 cm (k=40.0 W/(m-K); Density = 7800.0 kg/m^3; and specific heat = 600.0 J/(kg-K)). The ball bearing is initially at a uniform temperature of 1100 K and is then suddenly exposed to convection with a convection temperature of 320.0K and a convection coefficient of 25.0 W/(m2-K). Calculate the following: a) Calculate the time required to cool this ball bearing down to a temperature of 410.0 K. b) Calculate the amount of heat removed from the ball bearing during this cooling process.arrow_forward
- Thermodynamics problem. 2.6 A membrane type electrical heater of 20,000 W/m2 capacity is sandwiched between an insulation of 25 mm thickness with thermal conductivity of 0.029 W/mK and a metal plate with k = 12.6 W/mK of thickness 15 mm. The convection coefficient is 150 W/m2K. The surroundings are at 5°C. Determine the surface temperature of the heater and the flow on either side.arrow_forwardThe heat conducts through the shape below. The temperature of the right face is 93 °C, while the left face is at 23 °C. If the top and bottom faces are completely insulated, and the thermal conductivity of the material decreases with decreasing temperature. * Assume that the thermal conductivity is 100 at 23, decreased to 10 at 93. A) Sketch the temperature profile inside the plate. B) If both sides of the plate in the above problem is exposed to air: Left side (h = 20 W/m2K, TL = 20 °C) and right side (h = 90 W/m2K). Calculate the temperature of the air on the right side.arrow_forwardA 1 in. o.d. (outer diameter) tube reactor is insulated with a 3 inch layer of asbestos. If the temperature of the outer surface of the insulation is 100 °F and the rate of heat loss per foot of reactor length is 50 BTU/hr, what must the temperature of the inside of the reactor be? [for asbestos, k = 0.105 BTU/hr ft °F]arrow_forward
- The wall of a furnace is made up of a material which has thermal conductivity of 2.65 W/m◦C and a thicknesses 300 mm. The inner side of the furnace wall is exposed to hot gases at 1200 ⁰C with a convection coefficient of 20 W/m2⁰C and the inside the surface is at 700 ⁰C. The air outside the furnace is at 20⁰C with a convection coefficient of 15 W/m2⁰C. Draw a clear diagram representing the system Determine the temperature of the outside surface of the furnace The rate of heat loss from the furnace.arrow_forward1. A simple cavity wall consists of two brick layers separated by an air gap of 50 mm. If the inside air temperature is 20oC and the ambient outside temperature is 5 oC, calculate the heat flux through the wall. Bricks are 100 mm thick with thermal conductivity kbrick = 0.5 W/m K, hin = 10 W/m2 K, hout = 20 W/m2 K. The internal air cavity can be considered still (no convection) with kair = 0.015 W/m K. 2. On a day in winter, the outside air temperature drops to -5 oC and the outside convective heat transfer changes to hout = (2 x V) + 8.9 W/m2 K. If the outside wind speed gusts at 50 kph, calculate the change in heat flux for the wall in question 3.arrow_forwardQuestion One Explain how heat is transferred from one point to another illustrating with appropriate diagram. Calculate the heat flow per square meter (heat flux) through water medium with thermal conductivity of 0.6, flowing in a 5 cm thickness space, if the temperatures on the two surfaces are 50 and 210°C, respectively. Question 2 Distinguish between force and free convection with the aid of appropriate illustrations. What is the approximate temperature difference between a hot plate and the surrounding air if the heat flux from the plate is 800 W/m2? Assume that the air is flowing past the surface with a velocity of 5 m/s giving a heat transfer coefficient of 20 W/(m2K). Question 3 Explain the differences between laminar and turbulent flow Water (ν = 0.86x10-6m2/s) flows through a tube with the diameter 12 mm at a velocity of 2 m/s. Determine if the flow is laminar or turbulent!arrow_forward
- A hot steam pipe having an inside surface temperature of 250°C has an inside diameter of 8 cm and a wall thickness of 5.5 mm. It is covered with a 9-cm layer of insulation having k =0.5 W/m-°C, followed by a 4-cm layer of insulation having k =0.25W/m-°C. The outside temperature of the insulation is 20°C. Calculate the heat lost per meter of length. Assume k =47 W/m-°C for the pipe.arrow_forwardThe cylindrical pipe with a thread diameter of 0.070 m and an internal diameter of 0.050 m is insulated both internally and externally. Calculate the heat loss per unit length of the pipe (1 m) when the inner surface temperature of the pipe is kept at 50 °C and the outer surface temperature at 20 °C (Average thermal conductivity constant = Km= 0.172 J/cm.s.K).arrow_forwardA horizontal, high-pressure steam pipe of 0.1 m outside diameter passes through a large room whose wall and air temperatures are at 23°C. The pipe has an outside surface temperature of 165°C and an emissivity of 0.85. Estimate the heat loss from the pipe per unit length (W/m) by radiation.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license