Mathematics for Machine Technology
7th Edition
ISBN: 9781133281450
Author: John C. Peterson, Robert D. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 47, Problem 13AR
To determine
(a)
The cutting speed.
To determine
(b)
The RPM of the aluminum cylinder.
To determine
(c)
The total cutting time.
To determine
(d)
The pitch of the gear.
To determine
(e)
The whole depth of the gear.
To determine
(f)
The center distance between the gear and the pinion.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, advanced-math and related others by exploring similar questions and additional content below.Similar questions
- Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. Determine the revolutions per minute of an aluminum alloy rod 1.250 inches in diameter with a cutting speed of 550 feet per minute.arrow_forwardCompute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. An annealed cast iron housing is drilled with a cutting speed of 20 meters per minute using a 22-millimeter diameter carbon steel drill. Find the revolutions per minute.arrow_forwardCompute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. A high-speed steel milling cutter with a 1.750-inch diameter and a cutting speed of 40 feet per minute is used for a roughing operation on an annealed chromium-nickel steel workpiece. Find the revolutions per minute.arrow_forward
- Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. What is the surface speed of a 16-inch diameter surface grinder wheel running at1194 rpm?arrow_forwardCompute the following problems. Express the answers to 1 decimal place. Use: T=LFN Fifteen 3.20-millimeter diameter holes each 57.15 millimeters deep are drilled inan aluminum workpiece. The high-speed steel drill runs at 9200 r/min with a feedof 0.05 millimeter per revolution. Determine the total cutting time.arrow_forwardCompute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. A 312 inch diameter high-speed steel cutter, running at 55 rpm, is used to rough mill a steel casting. What is the Cutting speed?arrow_forward
- In Figure 208, gear A is turning at 120 revolutions per minute and gear B is turning at 3.6 revolutions per second. Determine the ratio of the speed of gear A to the speed of gear B.arrow_forwardA plug gage tapers 3.10 mm along a 38.00 mm length, as shown in Figure 215. Set up a proportion and determine the amount of taper in the workpiece for each of the following problems. Express the answers to 2 decimal places.arrow_forwardCompute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. A finishing cut is taken on a brass workpiece using a 100-millimeter diameter carbon steel milling cutter. What is the cutting speed when the cutter is run at 86 r/min?arrow_forward
- Of two gears that mesh, the one that has the greater number of teeth is called the gear, and the one that has the fewer teeth is called the pinion (Figure 218). For each of the problems, set up a proportion, and determine the unknown value, x. Round the answers to 1 decimal place where necessary.arrow_forwardCompute the following problems. Express the answers to 1 decimal place. Use: T=LFN A slot 812.00 millimeters long is cut into a carbon steel baseplate with a feed of0.80 millimeter per revolution. Find the cutting time using a 75-millimeter diameter carbide milling cutter running at 640 r/min.arrow_forwardFind the intensity of light at a depth of 12 meter if I0=14 and k=0.7. Round to two decimals.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mathematics For Machine TechnologyAdvanced MathISBN:9781337798310Author:Peterson, John.Publisher:Cengage Learning,
College Algebra (MindTap Course List)AlgebraISBN:9781305652231Author:R. David Gustafson, Jeff HughesPublisher:Cengage Learning
Algebra: Structure And Method, Book 1AlgebraISBN:9780395977224Author:Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. ColePublisher:McDougal Littell
Mathematics For Machine Technology
Advanced Math
ISBN:9781337798310
Author:Peterson, John.
Publisher:Cengage Learning,
College Algebra (MindTap Course List)
Algebra
ISBN:9781305652231
Author:R. David Gustafson, Jeff Hughes
Publisher:Cengage Learning
Algebra: Structure And Method, Book 1
Algebra
ISBN:9780395977224
Author:Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole
Publisher:McDougal Littell
Finding the length of an arc; Author: Maths Genie;https://www.youtube.com/watch?v=fWGPf5peCc8;License: Standard YouTube License, CC-BY
Circles, Angle Measures, Arcs, Central & Inscribed Angles, Tangents, Secants & Chords - Geometry; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=nd46bA9DKE0;License: Standard Youtube License