Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 51, Problem 14RQ
Backing plates, struts, levers, and other metal brake parts should be.
- wet-cleaned using water or a water-based solution
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following statements about drum
brake shoes is not true?
a. Linings may be riveted or bonded to the shoes.
b. Shoe indentions hold the shoe in place
against the backing plate.
c. The shoe rim supports the shoe lining.
d. The primary/leading shoe is typically the one
that is positioned toward the front of the
vehicle.
When replacing brake pads on a vehicle: Technician A works on one wheel before beginning work on an-other. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct?
Asbestos has not been used in brake linings or pads since 2003.
a. True b. False
Technician A says low-drag calipers retract the pistons and pads farther from the rotor than traditional calipers. Technician B says systems that use low-drag calipers cannot use quick take-up master cylinders. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
A brake line must be single-flared to provide a good seal at a joint or junction block.
a. True b. False
Vehicles use brake pedal position sensors.
a. True b. False
Chapter 51 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 51 - Name the two methods of attaching brake lining...Ch. 51 - Explain how drum brakes create a self-multiplying...Ch. 51 - List at least five separate types of wear and...Ch. 51 - What is the job of wheel cylinder stops?Ch. 51 - Explain the operation of an integral drum brake...Ch. 51 - In a typical drum brake, which component provides...Ch. 51 - True or False? The name duo-servo drum brake is...Ch. 51 - Prob. 8RQCh. 51 - Which of the following statements about drum brake...Ch. 51 - Brake linings should be replaced when. linings are...
Ch. 51 - In the unapplied position, drum brake shoes arc...Ch. 51 - Duo-servo drum brakes are also known as what type...Ch. 51 - On most vehicles, the automatic adjuster cables or...Ch. 51 - Backing plates, struts, levers, and other metal...Ch. 51 - A buildup of brake dust and dirt between the...Ch. 51 - Technician A says that an out-of-round drum can...Ch. 51 - Technician A says that a grinding noise from a...Ch. 51 - It has been determined that chatter and brake pull...Ch. 51 - Technician A says that the discard dimension of a...Ch. 51 - After resurfacing a brake drum: Technician A...Ch. 51 - Drum linings are badly worn at their heel and toe:...Ch. 51 - When machining brake drums: Technician A tries to...Ch. 51 - While discussing what would happen if too much...Ch. 51 - Technician A checks the surface of the drum for...Ch. 51 - While discussing pull during braking: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? Backing plates, struts, levers, and other metal brake parts should be cleaned with a wet-cleaned using water or a water-based solution.arrow_forwardTrue or False? Semimetallic brake pads still often are made with asbestos.arrow_forwardAfter resurfacing a brake drum: Technician A cleans it using hot water and a lint-free cloth. He then uses compressed air to thoroughly dry it Technician B cleans the drum using a lint-free cloth dipped in a special brake cleaning solvent. She then allows the drum to dry before reinstallation. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- True or False? Disc brakes are not as likely to fade during heavy braking as are drum brakes.arrow_forwardTrue or False? If brake fluid is discolored, the system must be flushed and the fluid replaced.arrow_forwardWhich of the following can lead to brake hose failure? Improperly matched fittings Stressing the hose during installations Deterioration from heat and contaminants All of the abovearrow_forward
- Brake linings should be replaced when. linings are worn to within */3 inch of a rivet head linings are contaminated with oil or grease linings are contaminated with brake fluid all of the abovearrow_forwardThe basic frictional parts of a brake system are being discussed: Technician A says that the harder the frictional parts are pushed together, the higher the friction. Technician B says that the harder the frictional parts are pushed together, the more heat is developed. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhen replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on another. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- During a brake inspection, the inner brake pad is found to be 3mm thick, while the outside pad is 8mm. Techinician A says this is a sign of a poorly lubricated hardware. Technician B says this is normal wear for brake pads. Who is correct? A. Technician A B. Technician B C. Both Technician A and B D. Neither Technician A or Barrow_forwardWhich of the following is not a factor in determiningthe effectiveness of a brake system?a. Heat dissipationb. Lubricantc. Pressured. Frictional contact areaarrow_forwardDuring a brake inspection, the inner brake pad is found to be 3mm thick, while the outside pad is 8mm. Technician A says this is a sign of a poorly lubricated hardware. Technician B says this is normal wear for brake pads. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License