Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 55, Problem 7MC
The high-side pressure on a system with a cycling clutch and pressure cycling switch is 145 psi, the low-side pressure is 28 psi, and the ambient temperature is
a. The system is undercharged.
b. The system is overcharged.
c. The system is normal.
d. The evaporator pressure regulator is bad.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
State 5 main faults and hazards in the pressurized system and the way to avoid them.
Which of the following is not a component of a pneumatic system?
Group of answer choices
An electric motor
A pump
None of these are true
A valve
An actuator
Technician A says throttle pressure is controlled directly by the pressure regulator valve. Technician B says one of the primary purposes of the pressure regulator valve is to fill the torque converter with fluid. Who is correct?
a.
A only
b.
B only
c.
Both A and B
d.
Neither A nor B
Chapter 55 Solutions
Automotive Technology
Ch. 55 - What should you do if you suspect that an...Ch. 55 - Explain how dye can be used to find leaks in the...Ch. 55 - What is the purpose of the thermostatic switch in...Ch. 55 - Why should the probe of an electronic leak...Ch. 55 - How will air trapped in the A7C system affect...Ch. 55 - Which of the following statements best defines the...Ch. 55 - Which of the following statements is not true...Ch. 55 - To charge an air-conditioning system while it is...Ch. 55 - All of the following are true statements about...Ch. 55 - A very important part of a performance test on an...
Ch. 55 - While conducting a pressure test on an A/C system,...Ch. 55 - The high-side pressure on a system with a cycling...Ch. 55 - When checking an A/C system, the evaporators inlet...Ch. 55 - All of these are good reasons for replacing an...Ch. 55 - In an AZC system, if the low-side pressure is...Ch. 55 - Technician A says that evacuating (pumping down)...Ch. 55 - Technician A says that some refrigerant leaks can...Ch. 55 - Technician A says that the presence of oil around...Ch. 55 - Technician A says that a faulty accumulator will...Ch. 55 - Technician A says that air in the system can cause...Ch. 55 - Technician A feels up and down the face or along...Ch. 55 - Technician A says that a manifold gauge set can be...Ch. 55 - While discussing an inoperative blend air door:...Ch. 55 - Two technicians were discussing how comparing the...Ch. 55 - While conducting an A/C system performance test:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The high-side pressure on a system with a cycling clutch and pressure cycling switch is 245 psi, the low- side pressure is 28 psi, and the ambient temperature is 78°F. What do these gauge readings indicate? The system is undercharged. The system is overcharged. The system is normal. The evaporator pressure regulator is bad.arrow_forwardWhat is the purpose of the thermostatic switch in a cycling clutch system?arrow_forwardWhile discussing the results of an oil pressure test: Technician A says that when the fluid pressures are high, internal leaks, a clogged filter, low oil pump out put, or a faulty pressure regulator valve are indicated. Technician B says that if the fluid pressure increased at the wrong time, an internal leak at the servo or clutch seal is indicated. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Which of the following is electrically connected in series with the compressor electromagnetic clutch? Ambient temperature switch Thermostatic switch Pressure cycling switch All of the abovearrow_forwardPneumatic Systems Explain the following in at least 10 sentences: What is controlled cabin pressure leakage?arrow_forwardTrue or False: Pneumatic controls are explosion-proof.arrow_forward
- True or False? If the fluid reservoir for a hydraulic clutch is low, the entire system should be checked for fluid leaks.arrow_forwardAnswer the following question: 1. On an aircraft enumerate the turboprop starting procedures.arrow_forwardOn the low-pressure side of a double diaphragm seal system, the transmitter measures a pressure of 108 in. WC when the tank is empty. Which process should you apply before measuring on the high-pressure side? Low water level cutoff Ratholing Zero suppression Blowdownarrow_forward
- While diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?arrow_forward37- Technician A says that all transmission opening pressure are derived from the regulated output flow of the oil pump. Technician B says that every automatic transmission uses one, or more, pressure regulator valves. Who is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor Barrow_forwardExplain why a diode may be wired into the compres sor clutch circuitarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License