Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 8, Problem 8.14PP
At approximately what volume flow rate will propyl alcohol at
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
At approximately what volume flow rate will propyl alcohol at 77 °F become turbulent when flowing in a 3-in Type K copper tube?
Calculate the fitting coefficient, , for the sudden expansion when fluid flows from a tube with a radius of 6 mm, to one with a radius of 24 mm. Assume the Reynolds number is 5,000 in the first tube. Enter your answer in decimal form, not scientific notation.
Estimate the entrance length for motor oil for the following two cases: (a) SAE10W-30 oil flowing through a 0.1-in diameter tube in an engine at 0.01 gal/s and (b) SAE 10W-30 oil flowing through a 6-in diameter pipe at 500 gal/s.
Chapter 8 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 8 - A 4-in-ductile iron pipe carries 0.20ft3/s of...Ch. 8 - Calculate the minimum velocity of flow in ft/s of...Ch. 8 - Calculate the maximum volume flow rate of fuel oil...Ch. 8 - Calculate the Reynolds number for the flow of each...Ch. 8 - Determine the smallest metric hydraulic copper...Ch. 8 - In an existing installation, SAE 10 oil (sg = 0.89...Ch. 8 - From the data in Appendix C, we can see that...Ch. 8 - Compute the Reynolds number for the flow of 325...Ch. 8 - Benzene (sg = 0.86 ) at 60c C is flowing at 25...Ch. 8 - Hot water at 80 C is flowing to a dishwasher at a...
Ch. 8 - A major water main is an 18 -in ductile iron pipe....Ch. 8 - ]8.12 An engine crankcase contains SAE 10 motor...Ch. 8 - Repeat Problem 8.12 for an oil temperature of 160...Ch. 8 - At approximately what volume flow rate will propyl...Ch. 8 - SAE 30 oil (sg = 0.89 ) is flowing at 45 L/min...Ch. 8 - Repeat Problem 8.15 for an oil temperature of 160...Ch. 8 - Repeat Problem 8.15, except the tube is 50 mm...Ch. 8 - Repeat Problem 8.17 for an oil temperature of 0 C.Ch. 8 - The lubrication system for a punch press delivers...Ch. 8 - After the press has run for some time, the...Ch. 8 - A system is being designed to carry 500 gal/min of...Ch. 8 - The range of Reynolds numbers between 2000 and...Ch. 8 - The water line described in Problem 8.22was a cold...Ch. 8 - In a dairy, milk at 100 F is reported to have a...Ch. 8 - In a soft-drink bottling plant, the concentrated...Ch. 8 - ]8.26 A certain jet fuel has a kinematic viscosity...Ch. 8 - Crude oil is flowing vertically downward through...Ch. 8 - Water at 75 C is flowing in a standard hydraulic...Ch. 8 - Fuel oil is flowing in a 4 -in Schedule 40 steel...Ch. 8 - A 3-in Schedule 40 steel pipe is 5000 ft long and...Ch. 8 - Benzene at 60 C is flowing in a DN 25 Schedule 80...Ch. 8 - As a test to determine the effective wall...Ch. 8 - Water at F flows from a storage tank through ft...Ch. 8 - A water main is an 18 -in-diameter concrete...Ch. 8 - Figure 8.12shows a portion of a fire protection...Ch. 8 - A submersible deep-well pump delivers 745 gal/h of...Ch. 8 - On a farm, water at 60 F is delivered from a...Ch. 8 - Figure 8.15 shows a system for delivering lawn...Ch. 8 - A pipeline transporting crude oil (sg = 0.93 ) at...Ch. 8 - For the pipeline described in Problem 8.39,...Ch. 8 - Water at 10 C flows at the rate of 900 L/min from...Ch. 8 - For the system shown in Fig. 8.17, compute the...Ch. 8 - Fuel oil (sg = 0.94 ) is being delivered to a...Ch. 8 - Figure 8.18 shows a system used to spray polluted...Ch. 8 - In a chemical processing system, the flow of...Ch. 8 - Water at 60 F is being pumped from a stream to a...Ch. 8 - For the pump described in Problem 8.46, if the...Ch. 8 - Gasoline at 50 F flows from point A to point B...Ch. 8 - Figure 8.20 shows a pump recirculating 300 gal/min...Ch. 8 - Linseed oil at 25 C flows at 3.65 in a standard...Ch. 8 - Glycerin at 25 C flows through a straight...Ch. 8 - Water at 75 C flows in a standard hydraulic copper...Ch. 8 - Benzene (sg = 0.88 ) at 60 C, flows in a DN 25...Ch. 8 - Water at 80 F flows in a 6 -in coated ductile iron...Ch. 8 - Water at 50 F flows at 15.0 ft3/s in a concrete...Ch. 8 - Water at 60 F flows at 1500 gal/min in a 10 -in...Ch. 8 - ]8.57 A liquid fertilizer solution (sg = 1.10 )...Ch. 8 - Crude oil (sg = 0.93 ) at 100 C flows at a rate of...Ch. 8 - Water at 65 C flows in a DN 40 Schedule 40 steel...Ch. 8 - Propyl alcohol flows in a standard hydraulic...Ch. 8 - ]3.61 Water at 70 F flows in a 12 -in-diameter...Ch. 8 - Heavy fuel oil at 77 F flows in a 6 -in Schedule...Ch. 8 - Water flows at a rate of 1.50ft3/s through 550 ft...Ch. 8 - Compute the energy loss as water flows in a...Ch. 8 - ]8.65 A water main is an 18 -in-diameter concrete...Ch. 8 - A fire protection system includes 1500 ft of 10...Ch. 8 - ]8.67 A standard hydraulic copper tube, 120 mm...Ch. 8 - Compute the energy loss as 2.0ft3/s of water flows...Ch. 8 - It is desired to flow 2.0ft3/s of water through...Ch. 8 - Specify a suitable size of new, clean Schedule 40...Ch. 8 - For the pipe selected in Problem 8.70, compute the...Ch. 8 - Compare the head loss that would result from the...Ch. 8 - In Problem 6.107, a theoretical flow rate of water...Ch. 8 - A pipeline is needed to transport medium fuel oil...Ch. 8 - Medium fuel oil at 25 C is to be pumped at a flow...Ch. 8 - A tremendous amount of study has gone into the...Ch. 8 - In a given installation, it is determined that the...Ch. 8 - "Laminar" fountains have become quite popular due...Ch. 8 - Use PIPE-FLO to model a straight horizontal run of...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40 steel pipe if the vol- ume flow rate is 0.25 ft/s: (a) water at 60°F. (b) acetone at 77 F, (c) castor oil at 77 E, and (d) SAE 10 oil at 210°(Sg 0.87),arrow_forwardThe working fluid of the pressure gauge in Fig. 157 is mercury. Estimate the volumetric flow rate in the tube if the fluid flowing through it is (a) gasoline and (b) nitrogen, at 20 ° C and 1 atmarrow_forwardAir at a pressure of 120 psig and a temp of 50 deg F is flowing at a rate of 500 lbs/ hr through a 2” sch. 40 steel pipe. What is the pressure drop per foot of pipe?arrow_forward
- A pitot tube with dia of 3cm is installed in a pipe with ID150 mm. Water flows through the pipe, and the determined pressure drop across the pitot tube is 45 kPa. What is the average velocity of the flow.arrow_forwardCalculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40 steel pipe if the vol-ume flow rate is 0.25 ft3 / s: (a) water at 60F, (b) acetone at 77F, (c) castor oil at 77F, and (d) SAE 10 oil at 210F (sg = 0.87).arrow_forwardA machined entrance cone venture tube that has been fabricated according to ASME standards is fit to a 7 cm ID water pipe. The minimum diameter is 4 cm. If the pressure drop across the venture is 19 kPa, calculate the water flow rate.arrow_forward
- What pressure head drop will occur in 300 ft of new horizontal cast iron pipe, 4" in diameter, carrying medium fuel oil at 50°F when the velocity is 0.25 ft/sec?arrow_forwardFlow In Closed Conduits 4. Water flows at 70F flows in a 6-in. diameter new galvanized iron pipe at a rate of 0.95 cfs and is 570 ft long. (a) Calculate the heat lost due to friction. (b) What pressure must be maintained at point ‘A’ if the pressure at point ‘B’, which is 47.5 ft higher than point ‘A’, is 35 psi? Answers: (a) ______________________________(b) _______________________________arrow_forwardQuestion - You must discuss in detail the way in which the pitot tube and nozzle flow meter are used to calculate velocity or volume flow rate. Write the velocity (or flow rate) equations for both and a detailed description of the what you did.arrow_forward
- A pitot-static tube is used to measure the velocity of water in a pipe. The stagnation pressure head is 10 m and static pressure head is 8 m. Calculate the velocity of flow if the coefficient of pitot tube equal to 0.95arrow_forwardCompute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K copper tube if the volume flow rate of water at 60'F is Q 0.5 gal/min. Use increments of 0.05 in and include the velocity at the centerline. please be through and provide all calculus and graphs/tablesarrow_forwardWhat is the critical velocity for an oil of viscocity 4.413x10-6m2/s flowing through 152.4mm diameter pipe?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License