Concept explainers
For the system shown in Fig. 8.17, compute the power delivered by the pump to the water to pump
Learn your wayIncludes step-by-step video
Chapter 8 Solutions
Applied Fluid Mechanics (7th Edition)
Additional Engineering Textbook Solutions
Statics and Mechanics of Materials (5th Edition)
Applied Statics and Strength of Materials (6th Edition)
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Mechanics of Materials (10th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Engineering Mechanics: Dynamics (14th Edition)
- Calculate the minimal head of the pump required to pump 1 m³ of water per second to the height 10 m trough a pipe with cross sectional area 0.1 m². Assume constant friction coefficient f = 0.04 and neglect all losses in fittings. The pump head is the gravity head plus losses and so it can be found?arrow_forwardWater from a nearby lake is to be used for a fountain and a water tank. The figure below shows the elevations and pipe connections. It is desired that the jet water of the fountain reaches a height of at least 2.5 m from the nozzle outlet. As for the tank, it is elevated in order for it to distribute water using gravity. The specifications of nozzle, suction and discharge pipes are given in the table below. Assuming negligible minor head losses, what is the minimum power input to the pump in kW? Take pump efficiency to be 88% and motor efficiency, 95%. Water from the fountain is returned to the lake through a drainage (not shown in the figure). round off the answer to 4 decimal placesarrow_forwardQuestion 8 Two reservoirs are connected by a pipe whose total length is 360m.From the upper reservoir the pipe is 300mm in diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water levels between the two reservoirs are 8m.Take f=0.006 for the smaller pipe and f=0.005 for the larger pipe.If all the changes in pipe sections are sharp and sudden, calculate the flow rate which can be delivered.arrow_forward
- A storage reservoir supplies water to a pressure turbine under a head of 20 m. If the flow rate is 500 liters per second the head loss in the 300 mm pipe supplying the turbine is 2.5 m. Determine the pressure at the entrance of the turbine. If a negative pressure of 30 kPa exists at the 600 mm diameter section of the draft tube (exit tube) below the turbine 1.5 m below the supply line, estimate the energy absorbed by the turbine in kW neglecting losses between the entrance and exit of the pipe. Find also the output of the turbine assuming an efficiency of 85%arrow_forwardA pump is used to lift water at ambient temperature from one tank to another at a rate of 08/50 m3/min. If the pipe diameter is 4 in, calculate the power required to run the pump (efficiency 70%). The pipe material is commercial steel and contains 3 standard radius elbows. Assume h=1 cP. Calculate the Reynolds number and the friction head loss using the Moody chart attached, Using Colebrook equation. Calculate the other losses and the total loss, (Calculate the required power. Flow rate is not necessary for answering the question.arrow_forwardWater is pumped from a reservoir to a tank with a lift of 20.0 ft. The suction pipe, which connects the reservoir to the pump, has a 12in diameter and is 25ft long. The discharge pipe, which connects the pump to the tank, has a 10in diameter and is 450ft long. Both pipes may be classified as clean, smooth cast iron pipes. The suction pipe projects into the reservoir and discharge pipe projects into the tank. Considering all losses, calculate the horsepower required to operate the pump to discharge 1346 gpm into the tank.arrow_forward
- A hydraulic pump has a flow rate of 12 gpm and is rated for a maximum pressure of 2000 psi. if the pump is driven at 2100 rpm, what is the maximum Horsepower Output (HPout) of this pump?arrow_forwardA storage reservoir supplies water to a pressure turbine under a head of 20 m. If the flow rate is 500liters per second the head loss in the 300 mm pipe supplying the turbine is 2.5 m. Determine the pressure at the entrance of the turbine. If a negative pressure of 30 kPa exists at the 600 mm diametersection of the draft tube (exit tube) below the turbine 1.5 m below the supply line, estimate the energy absorbed by the turbine in kW neglecting losses between the entrance and exit of the pipe. Findalso the output of the turbine assuming an efficiency of 85%. *can you also provide its figure, Thank you.arrow_forwardThe volume flow rate of water that recirculates from the blade outlet to the impeller is estimated to be 0.4524 ft^3/min, and the losses through the shaft sealing is negligible. The hydraulic and mechanical efficiency of a centrifugal pump are 95% and 93%, respectively. If the pump delivers water a flow rate of 12 ft^3/min, calculate the pump efficiency in %.arrow_forward
- The pump delivers water from the lower to the upper reservoir at the rate of 2.0 ft. The head loss S between the suction pipe inlet and the pump is 6ft and that between the pump outlet and the upper reservoir IS 12ft. Both pipes 6 inches Schedule 40 steel pipe. Calculate a)The pressure at the pump inlet in Psi,b) The pressure at the pump outlet in Psi,c) The total head on the pump in ft, andd) The power delivered by the pump to the water in Hparrow_forwardReducer connection connecting a pipe that carries water with a diameter of A (mm) and another with a diameter of B (mm). If the pressure difference between the two ends of the joint is equal to C (mm) of mercury, calculate the average velocity at the inlet and outlet sections, and find the volumetric flow rate if the loss is small that can be neglected.arrow_forwardPROBLEM 1: A pipe transports 1962 N/s of water. The pipe tees into a 2"-diameter pipe and a 3"-diameter pipe. If the average velocity in the smaller-diameter pipe is 82 ft/s, calculate the flowrate (in ft^3/s) in the larger pipe.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY