Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 8, Problem 8.23PP
The water line described in Problem 8.22was a cold water distribution line. At another point in the system, the same-size tube delivers water at
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A machined entrance cone venture tube that has been fabricated according to ASME standards is fit to a 7 cm ID water pipe. The minimum diameter is 4 cm. If the pressure drop across the venture is 19 kPa, calculate the water flow rate.
Calculate the minimum velocity of flow in ft/s of water at 160°F in a 2-in steel tube with a wall thickness of 0.065 in for which the flow is turbulent.
At approximately what volume flow rate will propyl alcohol at 77 °F become turbulent when flowing in a 3-in Type K copper tube?
Chapter 8 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 8 - A 4-in-ductile iron pipe carries 0.20ft3/s of...Ch. 8 - Calculate the minimum velocity of flow in ft/s of...Ch. 8 - Calculate the maximum volume flow rate of fuel oil...Ch. 8 - Calculate the Reynolds number for the flow of each...Ch. 8 - Determine the smallest metric hydraulic copper...Ch. 8 - In an existing installation, SAE 10 oil (sg = 0.89...Ch. 8 - From the data in Appendix C, we can see that...Ch. 8 - Compute the Reynolds number for the flow of 325...Ch. 8 - Benzene (sg = 0.86 ) at 60c C is flowing at 25...Ch. 8 - Hot water at 80 C is flowing to a dishwasher at a...
Ch. 8 - A major water main is an 18 -in ductile iron pipe....Ch. 8 - ]8.12 An engine crankcase contains SAE 10 motor...Ch. 8 - Repeat Problem 8.12 for an oil temperature of 160...Ch. 8 - At approximately what volume flow rate will propyl...Ch. 8 - SAE 30 oil (sg = 0.89 ) is flowing at 45 L/min...Ch. 8 - Repeat Problem 8.15 for an oil temperature of 160...Ch. 8 - Repeat Problem 8.15, except the tube is 50 mm...Ch. 8 - Repeat Problem 8.17 for an oil temperature of 0 C.Ch. 8 - The lubrication system for a punch press delivers...Ch. 8 - After the press has run for some time, the...Ch. 8 - A system is being designed to carry 500 gal/min of...Ch. 8 - The range of Reynolds numbers between 2000 and...Ch. 8 - The water line described in Problem 8.22was a cold...Ch. 8 - In a dairy, milk at 100 F is reported to have a...Ch. 8 - In a soft-drink bottling plant, the concentrated...Ch. 8 - ]8.26 A certain jet fuel has a kinematic viscosity...Ch. 8 - Crude oil is flowing vertically downward through...Ch. 8 - Water at 75 C is flowing in a standard hydraulic...Ch. 8 - Fuel oil is flowing in a 4 -in Schedule 40 steel...Ch. 8 - A 3-in Schedule 40 steel pipe is 5000 ft long and...Ch. 8 - Benzene at 60 C is flowing in a DN 25 Schedule 80...Ch. 8 - As a test to determine the effective wall...Ch. 8 - Water at F flows from a storage tank through ft...Ch. 8 - A water main is an 18 -in-diameter concrete...Ch. 8 - Figure 8.12shows a portion of a fire protection...Ch. 8 - A submersible deep-well pump delivers 745 gal/h of...Ch. 8 - On a farm, water at 60 F is delivered from a...Ch. 8 - Figure 8.15 shows a system for delivering lawn...Ch. 8 - A pipeline transporting crude oil (sg = 0.93 ) at...Ch. 8 - For the pipeline described in Problem 8.39,...Ch. 8 - Water at 10 C flows at the rate of 900 L/min from...Ch. 8 - For the system shown in Fig. 8.17, compute the...Ch. 8 - Fuel oil (sg = 0.94 ) is being delivered to a...Ch. 8 - Figure 8.18 shows a system used to spray polluted...Ch. 8 - In a chemical processing system, the flow of...Ch. 8 - Water at 60 F is being pumped from a stream to a...Ch. 8 - For the pump described in Problem 8.46, if the...Ch. 8 - Gasoline at 50 F flows from point A to point B...Ch. 8 - Figure 8.20 shows a pump recirculating 300 gal/min...Ch. 8 - Linseed oil at 25 C flows at 3.65 in a standard...Ch. 8 - Glycerin at 25 C flows through a straight...Ch. 8 - Water at 75 C flows in a standard hydraulic copper...Ch. 8 - Benzene (sg = 0.88 ) at 60 C, flows in a DN 25...Ch. 8 - Water at 80 F flows in a 6 -in coated ductile iron...Ch. 8 - Water at 50 F flows at 15.0 ft3/s in a concrete...Ch. 8 - Water at 60 F flows at 1500 gal/min in a 10 -in...Ch. 8 - ]8.57 A liquid fertilizer solution (sg = 1.10 )...Ch. 8 - Crude oil (sg = 0.93 ) at 100 C flows at a rate of...Ch. 8 - Water at 65 C flows in a DN 40 Schedule 40 steel...Ch. 8 - Propyl alcohol flows in a standard hydraulic...Ch. 8 - ]3.61 Water at 70 F flows in a 12 -in-diameter...Ch. 8 - Heavy fuel oil at 77 F flows in a 6 -in Schedule...Ch. 8 - Water flows at a rate of 1.50ft3/s through 550 ft...Ch. 8 - Compute the energy loss as water flows in a...Ch. 8 - ]8.65 A water main is an 18 -in-diameter concrete...Ch. 8 - A fire protection system includes 1500 ft of 10...Ch. 8 - ]8.67 A standard hydraulic copper tube, 120 mm...Ch. 8 - Compute the energy loss as 2.0ft3/s of water flows...Ch. 8 - It is desired to flow 2.0ft3/s of water through...Ch. 8 - Specify a suitable size of new, clean Schedule 40...Ch. 8 - For the pipe selected in Problem 8.70, compute the...Ch. 8 - Compare the head loss that would result from the...Ch. 8 - In Problem 6.107, a theoretical flow rate of water...Ch. 8 - A pipeline is needed to transport medium fuel oil...Ch. 8 - Medium fuel oil at 25 C is to be pumped at a flow...Ch. 8 - A tremendous amount of study has gone into the...Ch. 8 - In a given installation, it is determined that the...Ch. 8 - "Laminar" fountains have become quite popular due...Ch. 8 - Use PIPE-FLO to model a straight horizontal run of...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of the piping is in 5-in. schedule 40 steel pipe. If the 2 fittings used is 90° ell standard long radius, The pump has an efficiency of 80%. Calculate the total friction losses in kJ/kg.arrow_forwardCalculate the resistance coefficient K for a check valve swing type placed in a 6 inch schedule 40 steel pipe if water at 100º F flowing with a velocity of 10 ft/sarrow_forwardImagine the plug in the sink described in Problem 8.31 leaks. If it now takes 45 seconds to fill the sink to its rim, estimate the volumetric flow rate of the leak.arrow_forward
- A pump is used to lift water at ambient temperature from one tank to another at a rate of 08/50 m3/min. If the pipe diameter is 4 in, calculate the power required to run the pump (efficiency 70%). The pipe material is commercial steel and contains 3 standard radius elbows. Assume h=1 cP. Calculate the Reynolds number and the friction head loss using the Moody chart attached, Using Colebrook equation. Calculate the other losses and the total loss, (Calculate the required power. Flow rate is not necessary for answering the question.arrow_forwardA piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping powerwith given flow conditions. Discuss the results. Flow conditions are same for both type of designs and given as: Pipe material: stainless steel Volume flow rate: 40 L/sec Assume the working fluid is water at standard atmosphere temperature and both tanks areopen to atmosphere. Pipe inlet is sharp-edged and bends are sharped without vanes. Elevations are as ?? = ?? ? and ?? = ?? ?arrow_forwardCompute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K copper tube if the volume flow rate of water at 60'F is Q 0.5 gal/min. Use increments of 0.05 in and include the velocity at the centerline. please be through and provide all calculus and graphs/tablesarrow_forward
- Compute the energy loss as water flows in a standard hydraulic copper tube, 120 mm OD X 3.5 mm wall, at a rate of 1000 L/min over a length of 45 m.arrow_forwardA water piping system is 3000 ft of NPS 20-inch pipe that has three gate valves, one globe valve, one lift check valve, and two standard tees through the flow. Calculate the total pipe length that will include all the straight pipe and valves and fittings. Calculate the pressure drop due to friction if the average flow rate is assumed to be 6.7 ft3/s. Take the value of the Darcy friction factor from Prob (1).arrow_forwardin a given setup, distilled water at 75 degree f has been found to be transported through a one and a half diameter horizontally oriented galvanized iron pipe running 1500 feet with a given flow rate of 0.1 cubic feet per second. what is the pressure drop in the given length of pipe assuming that the friction factor is take as 0.023?arrow_forward
- Calculatethe energy loss for water flowing at 8m/sthrough a standard tee fitting withan18-in ductile iron pipeif the flow is through the run of the tee.arrow_forwardWater is transported for 500 m in a 4 inch ductile iron pipe (coated) with a flow rate of 0.04 m3/s. Calculate the pressure drop over the 500 m length of pipe. (Calculate the friction factor f using the formula given in class notes/textbook, and not by using the Moody chart).arrow_forwardCalculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40 steel pipe if the vol- ume flow rate is 0.25 ft/s: (a) water at 60°F. (b) acetone at 77 F, (c) castor oil at 77 E, and (d) SAE 10 oil at 210°(Sg 0.87),arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License