A chromatogram exhibited three peaks for the compounds A, B, and Cat 14.8, 15.5, and 16.2 minutes, respectively. The peaks for A B, and Chave a base width of 0.74, 0.76, a 0.78 minutes, respectively. The column was 28.13 cm in length. The average value for N and HETP, respectively are: 9978 plates and 2.8+10-3 cm/plate 6652 plates and 4.2*10-3 cm/plate 416 plates and 6.8*10-2 cm/plate 326 plates and 8.6*10-2 cm/plate

A chromatogram exhibited three peaks for the compounds A, B, and Cat 14.8, 15.5, and 16.2 minutes, respectively. The peaks for A B, and Chave a base width of 0.74, 0.76, a 0.78 minutes, respectively. The column was 28.13 cm in length. The average value for N and HETP, respectively are: 9978 plates and 2.8+10-3 cm/plate 6652 plates and 4.210-3 cm/plate 416 plates and 6.810-2 cm/plate 326 plates and 8.6*10-2 cm/plate

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter8: Sampling, Standardization, And Calibration

Section: Chapter Questions

Problem 8.12QAP

See similar textbooks

Similar questions

In a chromatography experiment, a solution containing 0.083 7 M X and 0.066 6 M S gave peak areas of AX = 423 and AS 5 347. (Areas are measured in arbitrary units by the instrument.) To analyze the unknown, 10.0 mL of 0.146 M S were added to 10.0 mL of unknown, and the mixture was diluted to 25.0 mL in a volumetric flask. This mixture gave the chromatogram in Figure 5-8, with peak areas AX = 553 and AS = 582. Find the concentration of X in the unknown.
A new method is proposed to simultaneously detectand separatefour foodadditives by reversed-phase liquid chromatography. The data were obtained using theliquid chromatographic column with a flow rate of 0.5 mL per min and with the followingparameters: Pore size 100 A Particle Size 3.5 Internal diameter 4.6 mm Length 150 mm The food additives found in the sample resulted in the following data: ( see image for table) a.Calculate the number of plates from each peak. b.Calculate the plate height for the column. c.Retention factor for each peak.
A volume of 250 ml of a 0.05 M solution of a reagent of formula weight (relative molecular mass) 40 was made up, the weighing being done by difference. The standard deviation of each weighing was 0.0001 g. The standard deviation of the volume of solvent used was 0.05 ml. Express this as a relative standard deviation. Hence calculate the relative standard deviation of the molarity of the solution.
A quantitative analysis for an analyte gives a mean concentration of 12.6 ppm. The standard deviation due to the method, sm, is found to be 1.1 ppm, and that due to sampling, ss, is 2.1 ppm. By how much does the overall variance change if sm is improved by 10% and ss is improved by 15%?
A method for the detection of morphine is used to generate a calibration curve in which the assay response (y) is plotted versus morphine concentration (x, in mg/L). This gives a straight line with a slope (m) of 0.241 and a y-intercept (b) of 0.011, where y = mx + b. The slope of this line has a standard deviation of ±0.007, and the standard deviation of the intercept is ±0.006. If the sample from an athlete gives a response of 0.506 ± 0.013 in this method, what is the concentration of morphine in the sample and estimated precision of this concentration?
A chromatogram from a certain column has a peak with a w1/ 2 of 12 mm and a tr of 650 mm as measured. What is the number of theoretical plates?
A solution is prepared by weighing 5.0000 g of cesium iodide into a 100-mL volumetric flask. The balance used has a precision of 0.2 mg reported as a standard deviation, and the volumetric flask could be filled with a precision of 0.15mL also reported as a standard deviation. What is the estimated standard deviation of concentration (g/mL)?
1) Suppose you use your calibrated 25-mL pipet twice to deliver “50 mL" liquid, what is the actual total volume? What is the error in the final volume? 2) Suppose you use your uncalibrated 25-mL pipet to transfer liquid, what is the systematic error in the transferred volume? If you use it twice, what is the size if the systematic error in the total volume? My calibrated pipet had an average and standard deviation of 24.77 ml +/- 0.006 ml.
assignment 3. an exhibit shows a peak at 2.4 minutes in a gas chromatogram. a sample of known heroin also has a retention time of 2.4 minutes using the same instrument under the same conditions. the fact that both the unknown and the known have the same retention time is indicative of their being the same substance, but it does not prove this relationship. discuss?
According to the information given below, compute the correlation coefficient and the covariance coefficient between stock A and stock B. Standard deviation of the portfolio (stock A and stock B) : 0.37Standard deviation of the stock A : 0.38Standard deviation of the stock B : 0.43Weight for stock A : 0.60Weight for stock B : 0.40NOTE: PLEASE SHOW HOW YOU COMPUTE EACH OF THE ITEMS.
4.Consider the peaks for pentafluorobenzene and benzene in the gas chromatogram shown here. The elution time for unretained solute is 1.06 min. The open tubular column is 30.0 m in length and 0.530 mm in diameter, with a layer of stationary phase 3.0 μm thick on the inner wall. a) Measruing the width, w, at the baseline on the chromatogram, find the number of plates for these two compounds b) Use your answer to (a) to find the resolution between the two peaks c) Using the number of plates N=sqrtN1*N2 with the values from (a) calcuate what the resolution should be and compare your answer with the measured resolution in b
The method of standard additions was used to determine nitrite in a soil sample. A 1.00-mL portions of the soil extract sample was transferred to four 25-mL volumetric flasks. To each flask, increment volumes of a 1.00 x10-3M nitrite was added according to the table below. A colorimetric reagent was added to each flask to convert the nitrite into a colored product, and finally diluted to volume. What is the concentration of the nitrite in the soil extract based on the absorbance data below (with blank correction included)? Vol. of standard nitrite added, ml Absorbance 5.00 0.079 10.00 0.161 15.00 0.236 20.00 0.318 25.00 0.403