Principles of Highway Engineering and Traffic Analysi (NEW!!)
6th Edition
ISBN: 9781119305026
Author: Fred L. Mannering, Scott S. Washburn
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 4, Problem 10P
To determine
The probability that the pavement will have a PSI greater than
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A rigid pavement is designed with a 10-inch slab,an Ec of 6 million lb/in^2, a concrete modulus of rupture of 432 lb/in^2, a load transfer coefficient of 3.0, an initial PSI of 4.7, and a terminal serviceability index of 2.5.The overall standard deviation is 0.35, the modulus of subgrade reaction is 190 lb/in^3, and a reliability of 90%is used along with a drainage coefficient of 0.8. The pavement is designed assuming traffic is composed entirely of trucks (100 per day). Each truck has one 20-kip single axle and one 42-kip tandem axle (the effect of all other vehicles is ignored). A section of this road is to be replaced (due to different subgrade characteristics)with a flexible pavement having a structural number of 4 and is expected to last the same number of years as the rigid pavement. What is the assumed soil resilient modulus? (Assume all other factors are the same as for the rigid pavement.)
B. A rigid pavement with a 10-inch slab thickness, 90 percent reliability, E. = 4 million lb/in², 600 lb/in² modulus of rupture, 150 lb/in³ modulus of subgrade reaction, a 2.8 load transfer coefficient, initial PSI of 4.8, final PSI of 2.5, overall standard deviation of 0.35, and a drainage coefficient of 0.8 is designed. The pavement's design life is 20 years. The three-lane road is built for vehicles with one 20,000-pound single axle, one 26,000-pound tandem axle, and one 34,000-pound triple axle. Calculate the projected daily truck traffic on the three lanes.
A flexible pavement has a SN of 4 (all drainage coefficients are equal to 1.0). The initial PSI is 4.7 and the terminal serviceability is 2.5. The soil has a CBR of 9. The overall standard deviation is 0.40 and the reliability is 95%. The pavement is currently designed for 1800 equivalent 18-kip single-axle loads per day. If the number of 18-kip single-axle loads were to increase by 30%, by how many years would the pavement's design life be reduced? For SN, please round-off to the nearest whole number if necessary
Chapter 4 Solutions
Principles of Highway Engineering and Traffic Analysi (NEW!!)
Ch. 4 - Prob. 1PCh. 4 - Prob. 2PCh. 4 - Prob. 3PCh. 4 - Prob. 4PCh. 4 - Prob. 5PCh. 4 - Prob. 6PCh. 4 - Prob. 7PCh. 4 - Prob. 8PCh. 4 - Prob. 9PCh. 4 - Prob. 10P
Ch. 4 - Prob. 11PCh. 4 - Prob. 12PCh. 4 - Prob. 13PCh. 4 - Prob. 14PCh. 4 - Prob. 15PCh. 4 - Prob. 16PCh. 4 - Prob. 17PCh. 4 - Prob. 18PCh. 4 - Prob. 19PCh. 4 - Prob. 20PCh. 4 - Prob. 21PCh. 4 - Prob. 22PCh. 4 - Prob. 23PCh. 4 - Prob. 24PCh. 4 - Prob. 25PCh. 4 - Prob. 26PCh. 4 - Prob. 27PCh. 4 - Prob. 28PCh. 4 - Prob. 29PCh. 4 - Prob. 30PCh. 4 - Prob. 31PCh. 4 - Prob. 32P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine the safe thickness of rigid pavement if the wheel load is 85 kN and f'c=32 MPa.arrow_forwardA flexible pavement has a structural number of 3.8 (all drainage coefficients are equal to 1.0). The initial PSI is 4.7 and the terminal serviceability is 2.5. The soil has a CBR of 9. The overall standard deviation is 0.40 and the reliability is 95%. The pavement is currently designed for 1800 equivalent 18-kip single-axle loads per day. If the number of 18-kip single-axle loads were to increase by 30%, by how many years would the pavement design life be reduced?arrow_forwardanswer with complete solution. Asap 1. determine the safe thickness of rigid pavement if the wheel load is 85 kN and f'c = 32 MPaarrow_forward
- A rigid pavement is being designed with the same parameters as used in Problem 4.5. The modulus of subgrade reaction is 300 lb/in? and the slab thickness is determined to be 8.5 inches. The load transfer coefficient is 3.0, the drainage coefficient is 1.0, and the modulus of elasticity is 4 million 1b/in?. What is the design modulus of rupture? (Assume that any parameters not given in this problem are the same as those given in Problem 4.5.) 4.5 for reference: A flexible pavement was designed for the following daily traffic with a 12-year design life: 1300 single axles at 8000 Ib each, 900 tandem axles at 15,000 1b each, 20 single axles at 40,000 Ib each, and200 tandem axles at 40,000 lb each. The highway was designed with 4 inches of HMA wearing surface,arrow_forwardA flexible pavement was designed for the following daily traffic with a 12-year design life: 1300 single axles at 8,000 lb each, 900 tandem axles at 15,000 lb each, 20 single axles at 40,000 lb each, and 200 tandem axles at 40,000 lb each. The highway was designed with 4 inches of hot-mix asphalt (HMA) wearing surface, 4 inches of hot-mix asphaltic base, and 8 inches of crushed stone subbase. The reliability was 70%, overall standard deviation was 0.5, ¨PSI was 2.0 (with a TSI of 2.5), and all drainage coefficients were 1.0. What was the soil resilient modulus of the subgrade used in design?arrow_forwardA flexible pavement is constructed with 4 inches of hot-mix asphalt (HMA) wearing surface, 8 inches of emulsion/aggregate-bituminous base, and 8 inches of crushed stone subbase. The subgrade has a soil resilient modulus of 10,000 lb/in^2, and M2 and M3 are equal to 1.0 for the materials in the pavement structure. The overall standard deviation is 0.5, the initial PSI is 4.5, and the TSI is 2.5. The daily traffic has 1080 20-kip single axles,400 24-kip single axles, and 680 40-kip tandem axles. How many years would you estimate this pavement would last (how long before its PSI drops below a TSI of 2.5) if you wanted to be 99%confident that your estimate was not too higharrow_forward
- A flexible pavement is constructed with 4 inches of hot-mix asphalt wearing surface, 10 inches soil cement base and 10 inches crushed stone subbase. The subgrade has a soil resilient modulus of 12,000 lb/in2, M2 = 1.5 and M3=1.127 for the materials of the pavement structure. The overall standard deviation is 0.5, the initial PSI = 5.0 and the terminal serviceability index (TSI) is 2.5. The daily traffic has 3000 cars, 1000 trucks and 500 trailers. The axle weights are: How long in years would the pavement last if R = 98% ? (Final answer to 2 decimal places)arrow_forwardPavement Design and Analysis - Design a HMA pavement structure for a 6-lane divided urban highway using the AASHTO method to accommodate the traffic loads and conditions as follows. Give two alternative layer thickness combinations.arrow_forwardA concrete pavement is to be constructed for a four-lane urban expressway on a subgrade with an effective modulus of subgrade reaction k of 100 lb/in3. The accumulated equivalent axle load for the design period is 3.25 x 106. The initial and terminal serviceability indices are 4.5 and 2.5, respectively. Using the AASHTO design method, determine a suitable thickness of the concrete pavement if the working stress of the concrete is 600 lb/in2 and the modulus of elasticity is 5 x 106lb/in2. Take the overall standard deviation So as 0.30, the load-transfer coefficient J as 3.2, the drainage coefficient as 0.9, and R = 95%.arrow_forward
- Subject : Transportation Engineering Read the question carefully and give me right solution according to the question. Note: solve by using 45-deg cone pressure distribution method only The maximum wheel load that the pavement could carry is 120 kN. If the contact radius of the wheel is assumed to be 250 mm, and subgrade bearing capacity is equivalent to 0.24 Megapascals, calculate the subgrade layer thickness of the flexible pavement in mm using the 45-deg cone pressure distribution method.arrow_forwardQ2: The traffic on the design lane of a proposed four-lane rural interstate highway consists of 40% trucks. If classification studies have shown that the truck factor can be taken as 0.45, design a suitable flexible pavement using the 1993 AASHTO procedure if the AADT on the design lane during the first year of operation is 1150, pi = 4.5, and pt = 2.5 . Growth rate = 3% Design life = 20 years Reliability level = 95% Standard deviation = 0.45 The pavement structure will be exposed to moisture levels approaching saturation 20% of the time, and it will take about one week for drainage of water. Effective CBR of the subgrade material is 7. CBR of the base and subbase are 70 and 22, respectively, and Mr for the asphalt mixture, 3102 MPa (450,000 lb/in2).arrow_forwardA 33 mm thick flexible pavement carrles a static wheel load having a circular contact area of the tire ls 75 476 m㎡, the transmitted load is distributed across the wider area of the sub grade at an angle of 45°. The subgrade bearing value Is 180.0 Kpa, while that of the base is 450,0 Kpa.Sketch &Design the thickness of the base.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning