Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 43, Problem 4MC
Which of the following is a probable cause for a converter’s stall speed being below specifications?
a. Restricted exhaust
b. Slipping transmission clutches
c. Slipping transmission bands
d. Worn planetary gearset
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Tech A says that the weight of the flywheel smoothes out the engine’s power pulses. Tech B says that the flexplate and torque converter perform this same function. Who is correct?
briefly define the following:
1. airborne transmission
2. common vehicle transmission
3. contact transmission
What provisions are usually included on tractor engines to aid in the correct timing of the camshaft?
Chapter 43 Solutions
Automotive Technology
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - List five reasons for replacing a torque...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - What is checked during a stall test?Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What should you do if a valve does not move freely...
Ch. 43 - Which of the following is the most likely cause...Ch. 43 - When should the ATF level be checked on most...Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following gear ratios indicates an over-drive condition? a. 2.15:1 b. 1:1 c. 0.85:1 d. None of the abovearrow_forwardA poorly adjusted shift linkage can cause which of the following problems? a. Gear clash b. Hard shifting c. The gear to jump out d. All of the abovearrow_forwardTechnician A says that the rear hub of the torque converter is bolted to the flexplate. Technician B says that the flexplate is designed to be flexible enough to allow the front of the converter to move forward or back ward if it expands or contracts because of heat or pressure. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- While discussing shift mechanisms: Technician A says that the interlock notches hold the transmission in the selected gear. Technician B says that the detent notches prevent the selection of more than one gear during operation. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following would probably not be caused by a plugged filter screen at a solenoid? a. Erratic shifting b. No shift conditions c. A solenoid that will not energize d. Wrong gear startsarrow_forwardWhich of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forward
- Which of the following would not cause noise while driving in 2WD under a heavy throttle? a. Faulty ignition switch b. Worn transfer case clutch c. Inoperative locking hubs d. Bad front half shaftarrow_forwardTechnician A says that double-cone synchronizers have friction material on both sides of the synchronizer rings. Technician B says that multiple-cone synchronizers are used with larger engines and require a larger transmission housing. Who is correct?arrow_forwardWhat is the importance of studying on how to pull-out and mount manual transmission?arrow_forward
- What determines whether a conventional transmission or a transaxle is used?arrow_forwardTrue or False? In most transmissions and transaxles, there is one synchronizer assembly for each speed gear.arrow_forwardBefore making a clutch adjustment, it is necessary to______. a. measure clutch pedal free travel b. lubricate the clutch linkage c. check the hydraulic fluid level d. place the transmission in reversearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License