CONNECT F/SHIGLEY'S MECH.ENGR.DESIGN>I<
10th Edition
ISBN: 9781260058499
Author: BUDYNAS
Publisher: INTER MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 6, Problem 7P
A steel rotating-beam test specimen has an ultimate strength of 150 kpsi and a yield strength of 135 kpsi. It is desired to test low-cycle fatigue at approximately 500 cycles. Cheek if this is possible without yielding by determining the necessary reversed stress amplitude.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Suppose an ideally-prepared test specimen in an R.R. Moore rotating beam test has an ultimate strength of 159 ksi. The factor f is 0.73
If the specimen is subjected to a completely-reversing cyclic loading with a stress amplitude 105 ksi, how many cycles of life are expected?
A steel rotating-beam test specimen has an ultimate strength of 1600 MPa. Estimate the life of the specimenif it is tested at a completely reversed stress amplitude of 900 MPa.
A component is subjected to a maximum cyclic stress of 750 MPa and a minimum of 70 MPa. The steelfrom which it is manufactured has an ultimate tensile strength, σu, of 1050 MPa and a measured endurancelimit, σe, of 400 MPa. The fully reversed stress at 1000 cycles is 750 MPa. Using both the Goodman and Gerbermean stress correction procedures, calculate the component life.
Chapter 6 Solutions
CONNECT F/SHIGLEY'S MECH.ENGR.DESIGN>I<
Ch. 6 - A 10-mm steel drill rod was heat-treated and...Ch. 6 - Prob. 2PCh. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Repeat Prob. 6-5 with the specimen having an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Derive Eq. (6-17). Rearrange the equation to solve...Ch. 6 - For the interval 103 N 106 cycles, develop an...Ch. 6 - Estimate the endurance strength of a...
Ch. 6 - Two steels are being considered for manufacture of...Ch. 6 - A 1-in-diamctcr solid round bar has a groove...Ch. 6 - A solid square rod is cantilevered at one end. The...Ch. 6 - A rectangular bar is cut from an AISI 1020...Ch. 6 - A solid round bar with diameter of 2 in has a...Ch. 6 - The rotating shaft shown in the figure is machined...Ch. 6 - The shaft shown in the figure is machined from...Ch. 6 - Solve Prob. 6-17 except with forces F1 = 1200 lbf...Ch. 6 - Bearing reactions R1 and R2 are exerted on the...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with an alternating...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - The cold-drawn AISI KUO steel bar shown in the...Ch. 6 - Repeat Prob. 6-25 for a load that fluctuates from...Ch. 6 - An M14 2 hex-head bolt with a nut is used to...Ch. 6 - The figure shows a formed round-wire cantilever...Ch. 6 - The figure is a drawing of a 4- by 20-mm latching...Ch. 6 - The figure shows the free-body diagram of a...Ch. 6 - Solve Prob. 6-30 except let w1 = 2.5 in. w2 = l.5...Ch. 6 - For the part in Prob. 630, recommend a fillet...Ch. 6 - Prob. 33PCh. 6 - Prob. 34PCh. 6 - A part is loaded with a combination of bending,...Ch. 6 - Repeat the requirements of Prob. 6-35 with the...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 637 to 646 For the problem specified in the table,...Ch. 6 - For the problem specified in the table, build upon...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - Problem Number Original Problem, Page Number 637...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - Prob. 49PCh. 6 - Prob. 50PCh. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - Solve Prob. 6-17 except include a steady torque of...Ch. 6 - Solve Prob. 618 except include a steady torque of...Ch. 6 - In the figure shown, shaft A, made of AISI 1020...Ch. 6 - A schematic of a clutch-testing machine is shown....Ch. 6 - For the clutch of Prob. 657, the external load P...Ch. 6 - A flat leaf spring has fluctuating stress of max =...Ch. 6 - A rotating-beam specimen with an endurance limit...Ch. 6 - A machine part will be cycled at 350 MPa for 5...Ch. 6 - The material properties of a machine part are Sut...Ch. 6 - Repeat Prob. 662 using the Goodman criterion....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading conditions according to the Maximum shear stress hypothesis and the Maximum strain energy hypothesis. Shaft diameter: 20 mm, Shaft Length 120 mm, F1 = 750N, F2 = 3000N, Mb = 2400 N.mm. Steel if St37 and Safety coefficient is 2 If taken, will this stick work safely under these operating conditions? (Yield of given steel Strength 225 Mpa, Tensile strength 370 Mpa)arrow_forwardA round cross section cold drawn steel bar made of AISI 1020 has adiameter of 35 mm. Based on a conservative failure analysis, calculate factorof safety in the following conditions:a) The bar is subjected to static bending moment of 450 N.m, and steadytorque of 180 N.mb) The bar is subjected to bending moment fluctuating between(900 N.m and 400 N.m), and steady tension of 2.4 kNarrow_forwardA ¼ inch diameter steel rod is to carry an axial load of 2000 lbs. If the yield strength is 38 ksi, will the rod yield?arrow_forward
- A circular bar - shown below, made of AISI 1040 OQT 1300 steel (SU = 600 MPa), is loaded with an axial tensile loading P. Calculate the modified endurance strength (SE) and the modified fatigue strength (SF) for the bar if D = 36 mm, d = 30 mm, and r = 2.4 mm. Use the number of cycles to fracture to be 5 × 105. Assume that the surface finish factor, kf, is 0.85, the size factor, kS, is 0.85, and the notch sensitivity factor, qn, is 0.75. Use the following equations if needed,arrow_forwardA round bar of length l = 100 mm, diameter d = 20 mm, is subjected to an axial force P = 2000 N, a transverse force F = 11000 N, and a torque T = 110 N.m. The material is steel with Sy = 480 MPa. Using the distortion energy (Von Mises) yield criterion, calculate the safety factor at points A and B.arrow_forwardA thin-walled cylindrical tube with internal diameter and thickness of 50 mm and 0.5 mm, respectively is pressurized to 2 MPa. During installation, the cylindrical tube is also subjected to a bending moment of magnitude 10 N-m. The tube is made of aluminum alloy with the yield strength of 85 MPa.i) Calculate the stress state at the critical material point of the tube.ii) Determine if the loading would cause failure by yielding, based on the Tresca and von Mises yield criterion. Sketch the loci of the yield criteria in the principal stress axis and indicate the stress condition.arrow_forward
- A bar AISI 1035 steel forged and heat treated with minimum yield strength of 570MPa is subjected to bending moment of 290Nm and a torsional moment of 310Nm. Assuming a factor of safety of 2, determine the diameter of rod using the following theories of failure (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory, also specify which diameter is considered as safearrow_forwardA 4340 quench and tempered rotating steel shaft, d = 1 in, is loaded in fully reversed bending . The bar has been machined with surface conditions a = 1.34 ksi and b = -0.085, and will be operating at room temperature. The program requires a reliability of 99.99 percent. The fillet radii at all points is r = 0.08 in. The fatigue strength fraction f = 0.76, and the The ultimate strength (Sut) is 260 Ksi. Determine the endurance limit in the aforementioned conditionsarrow_forwardA 1.64 m long rectangular AISI 1020 cold rolled steel bar (10 mm x 25 mm) is subject to a torsional load of 76.6 N·m. What is the safety factor against yielding? (Use Shigley for material properties.)arrow_forward
- Tensile and fully reversed loading fatigue tests were conducted for a certain steelalloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa,respectively. If a rod of this material supply were subjected to a static stress of 600MPa and fully-reversed oscillating stresses whose total range was 700 MPa. Assuming garber relationship will this rod fail by fatigue failurearrow_forwardA forged steel bar, 50 mm in diameter, is subjected to a reversed bending stress of 250 MPa. The bar is made of 40 C8 with ultimate strength of 600 MPa. Calculate the endurance limit and life of the bar. Consider 90% reliability.arrow_forwardA rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 34 mm, and the rod length was 400 mm. When the applied torque reached 275.8 N·m, a shear strain of 2150 microradians was measured in the specimen. What was the angle of twist in the specimen?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY