CONNECT F/SHIGLEY'S MECH.ENGR.DESIGN>I<
10th Edition
ISBN: 9781260058499
Author: BUDYNAS
Publisher: INTER MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 6, Problem 61P
A machine part will be cycled at ±350 MPa for 5 (103) cycles. Then the loading will be changed to ±260 MPa for 5 (104) cycles. Finally, the load will be changed to ±225 MPa. How many cycles of operation can be expected at this stress level? For the part, Sut = 530 MPa, f = 0.9, and has a fully corrected endurance strength of Se = 210 MPa.
(a) Use Miner’s method.
(b) Use Manson’s method.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.c. What maximum torque is necessary to lower the load?d. What is the maximum torsional shear stress induced on the screw?
A 2Hp motor rotates at 1500 rpm. If the allowable torsional stress is not to exceed 40 MPa, what is the minimum diameter of shaft?
Hexagonal nuts for 6.25mm diameter bolts have a height of 5.5mm. If the ultimate strength of the nut material in shear is 103MPa, what is the most nearly the maximum allowable shear force on the nut thread using a safety factor of 5?
Chapter 6 Solutions
CONNECT F/SHIGLEY'S MECH.ENGR.DESIGN>I<
Ch. 6 - A 10-mm steel drill rod was heat-treated and...Ch. 6 - Prob. 2PCh. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Repeat Prob. 6-5 with the specimen having an...Ch. 6 - A steel rotating-beam test specimen has an...Ch. 6 - Derive Eq. (6-17). Rearrange the equation to solve...Ch. 6 - For the interval 103 N 106 cycles, develop an...Ch. 6 - Estimate the endurance strength of a...
Ch. 6 - Two steels are being considered for manufacture of...Ch. 6 - A 1-in-diamctcr solid round bar has a groove...Ch. 6 - A solid square rod is cantilevered at one end. The...Ch. 6 - A rectangular bar is cut from an AISI 1020...Ch. 6 - A solid round bar with diameter of 2 in has a...Ch. 6 - The rotating shaft shown in the figure is machined...Ch. 6 - The shaft shown in the figure is machined from...Ch. 6 - Solve Prob. 6-17 except with forces F1 = 1200 lbf...Ch. 6 - Bearing reactions R1 and R2 are exerted on the...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with a steady torsional...Ch. 6 - Repeat Prob. 6-20 but with an alternating...Ch. 6 - A bar of steel has the minimum properties Se = 40...Ch. 6 - The cold-drawn AISI KUO steel bar shown in the...Ch. 6 - Repeat Prob. 6-25 for a load that fluctuates from...Ch. 6 - An M14 2 hex-head bolt with a nut is used to...Ch. 6 - The figure shows a formed round-wire cantilever...Ch. 6 - The figure is a drawing of a 4- by 20-mm latching...Ch. 6 - The figure shows the free-body diagram of a...Ch. 6 - Solve Prob. 6-30 except let w1 = 2.5 in. w2 = l.5...Ch. 6 - For the part in Prob. 630, recommend a fillet...Ch. 6 - Prob. 33PCh. 6 - Prob. 34PCh. 6 - A part is loaded with a combination of bending,...Ch. 6 - Repeat the requirements of Prob. 6-35 with the...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 6-37 to 6-46For the problem specified in the build...Ch. 6 - 637 to 646 For the problem specified in the table,...Ch. 6 - For the problem specified in the table, build upon...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - Problem Number Original Problem, Page Number 637...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-37 to 6-46 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - 6-47 to 6-50 For the problem specified in the...Ch. 6 - Prob. 49PCh. 6 - Prob. 50PCh. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - 6-51 to 6-53 For the problem specified in the...Ch. 6 - Solve Prob. 6-17 except include a steady torque of...Ch. 6 - Solve Prob. 618 except include a steady torque of...Ch. 6 - In the figure shown, shaft A, made of AISI 1020...Ch. 6 - A schematic of a clutch-testing machine is shown....Ch. 6 - For the clutch of Prob. 657, the external load P...Ch. 6 - A flat leaf spring has fluctuating stress of max =...Ch. 6 - A rotating-beam specimen with an endurance limit...Ch. 6 - A machine part will be cycled at 350 MPa for 5...Ch. 6 - The material properties of a machine part are Sut...Ch. 6 - Repeat Prob. 662 using the Goodman criterion....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Calculate the allowable stress the material can be loaded under tension if the given design factor of safety is 2.5. Material, C1030 as rolled - Ultimate strength = 80,000 psi, Yield strength = 51,000 psiarrow_forwardA component is subjected to a maximum cyclic stress of 750 MPa and a minimum of 70 MPa. The steelfrom which it is manufactured has an ultimate tensile strength, σu, of 1050 MPa and a measured endurancelimit, σe, of 400 MPa. The fully reversed stress at 1000 cycles is 750 MPa. Using both the Goodman and Gerbermean stress correction procedures, calculate the component life.arrow_forwardA mild steel cover plate is to be designed for an inspection hole in the shell of a pressure vessel. The hole is 120 mm in diameter and the pressure inside the vessel is 6 N/mm2. Design the cover plate along with the bolts. Assume allowable tensile stress for mild steel as 60 MPa and for bolt material as 40 MPaarrow_forward
- The connecting rod in the figure is 10mm thick and manufactured from 8580M30 steel by cold drawing. The bar is threaded through the holes, loaded with fully variable load from the pins. Find the maximum load F to be applied to the part so that the part can have an indefinite life by looking at the appropriate figures for the stress concentrations that will occur due to the notch and drill hole.(Sut=600MPa,Sy=470Mpa)arrow_forwardCalculate the riveted joints, find its efficiency and draw a suitable sketch. Thickness of the plates – t, mm is 12 Width of the plates – b, mm is 150 Load – P, kN is 20 Note. Choose a suitable material, determine its tearing stress. Take permissible shearing stress - teta=0.7sigmat ; Permissible crushing stress - sigmac=1.5sigmat ;arrow_forwardA round cross-sectional bar d= 39 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a completely reversed stresses. What is the strength of failure (in MPa) If only 10 4 cycles are needed? (Take fully corrected Se = 358 MPa, no need to use modification fcactors) (accepted answer range +/- 5 MPa)arrow_forward
- What is the tensile strength of the bar if the yield stress is equal to 275MPa?arrow_forwardThe shaft below is an engine component that is rotating. It is machined from an unknown ductile material with a measured ultimate tensile strength of 700 MPa. Answer the questions below assuming a desired reliability of 99% and a fatigue fraction, f, of 0.9. Round all values and answers to 2 decimal places Determine the maximum stress in the shaft due to the applied loading (hint: what is the maximum moment?) Estimate the endurance limit (hint: what is the relationship between Se and Sut and don’t forget any necessary modifying factors.) Determine the number of cycles to failure.arrow_forwardIn the figure above, the shaft has a diameter of 50mm, and the diameter of pulleys C and D are given tobe 600 mm and 400 mm, respectively. ?1 = 1000 N, ?2 = 500 N and ?3 = 1500 N. But in addition tothe force on the pulleys, a compressive axial force of 100 kN is acting on both ends of the shaft. Theshaft is made from a brittle material with an ultimate tensile strength ??? that is half of its ultimatecompressive strength ???. The desired factor of safety is ? = 2 for the shaft.e. Determine the principal stresses corresponding to maximum bending and torsional shear stresses.Ignore transverse shear stresses due to bending.f. Use Maximum Normal Stress Theory and find the minimum required ??? and ???.g. Use Brittle Coulomb-Mohr Theory and find the minimum required ??? and ???.h. Use Modified Mohr Theory and find the minimum required ??? and ???.i. Use graphical method to check your answers in parts (a), (b) and (c).arrow_forward
- Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solutionarrow_forwardWhat will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?arrow_forward1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?c. What maximum torque is necessary to lower the load?d. What is the maximum torsional shear stress induced on the screw?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Hand Tools; Author: UCI Media;https://www.youtube.com/watch?v=4o0tqF0jDdo;License: Standard Youtube License