Statistics for Engineers and Scientists (Looseleaf)
4th Edition
ISBN: 9780073515687
Author: Navidi
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 7.3, Problem 7E
The coefficient of absorption (COA) for a clay brick is the ratio of the amount of cold water to the amount of boiling water that the brick will absorb. The article “Effects of Waste Glass Additions on the Properties and Durability of Fired Clay Brick” (S. Chidiac and L. Federico, Can J Civ Eng, 2007:1458–1466) presents measurements of the (COA) and the pore volume (in cm3/g) for seven bricks. The results are presented in the following table.
Pore volume | COA |
1.750 | 0.80 |
1.652 | 0.78 |
1.594 | 0.77 |
1.623 | 0.75 |
1.495 | 0.71 |
1.465 | 0.66 |
1.272 | 0.63 |
- a. Compute the least-squares line for predicting COA from pore volume.
- b. Compute the error standard deviation estimate s.
- c. Compute a 95% confidence interval for the slope.
- d. Find a 95% confidence interval for the
mean COA for bricks with pore volume 1.5 cm3/g. - e. Can you conclude that the mean COA for bricks with pore volume 1.5 cm3/g is less than 0.75? Perform a hypothesis test and report the P-value.
- f. Find a 95% prediction interval for the COA of a particular brick whose pore volume is 1.5 cm3/g.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The article “Wastewater Treatment Sludge as a Raw Material for the Production of Bacillus thuringiensis Based Biopesticides” (M. Tirado Montiel, R. Tyagi, and J. Valero, Water Research, 2001:3807–3816) presents measurements of total solids, in g/L, for seven sludge specimens. The results (rounded to the nearest gram) are 20, 5, 25, 43, 24, 21, and 32. Assume the distribution of total solids is approximately symmetric. a) Can you conclude that the mean concentration of total solids is greater than 14 g/L? Compute the appropriate test statistic and find the P-value. b) Can you conclude that the mean concentration of total solids is less than 30 g/L? Compute the appropriate test statistic and find the P-value. c) An environmental engineer claims that the mean concentration of total solids is equal to 18 g/L. Can you conclude that the claim is false?
An experiment was conducted to study the extrusion process of biodegradable packaging foam. Two of the factors considered for their effect on
the unit density (mg/ml) were the die temperature (145 °C vs. 155 °C) and the die diameter (3 mm vs. 4 mm). The results are stored in [Packaging
Foam 1]. Source: Data extracted from W. Y. Koh, K. M. Eskridge, and M. A. Hanna, "Supersaturated Split-Plot Designs," Journal of Quality
Technology, 45, January 2013, pp. 61-72.At the 0.05 level of significance,
3mm 4mm
57.22
145
72.54
145 53.60 66.70
145 48.13
49.28
145 69.89 44.14
145 62.78
58.37
145 55.18
53.98
155 57.50
63.03
155 54.17 46.73
155 73.86 60.17
155 90.28 46.78
155 88.19 43.27
155 82.61 56.93
Die Temperature
a. is there an interaction between die temperature and die diameter?
b. is there an effect due to die temperature?
c. is there an effect due to die diameter?
d. Plot the mean unit density for each die temperature for each die diameter.
e. What can you conclude about the effect of die…
King
Chapter 7 Solutions
Statistics for Engineers and Scientists (Looseleaf)
Ch. 7.1 - Compute the correlation coefficient for the...Ch. 7.1 - For each of the following data sets, explain why...Ch. 7.1 - For each of the following scatterplots, state...Ch. 7.1 - True or false, and explain briefly: a. If the...Ch. 7.1 - In a study of ground motion caused by earthquakes,...Ch. 7.1 - A chemical engineer is studying the effect of...Ch. 7.1 - Another chemical engineer is studying the same...Ch. 7.1 - Tire pressure (in kPa) was measured for the right...Ch. 7.1 - Prob. 10ECh. 7.1 - The article Drift in Posturography Systems...
Ch. 7.1 - Prob. 12ECh. 7.1 - Prob. 13ECh. 7.1 - A scatterplot contains four points: (2, 2), (1,...Ch. 7.2 - Each month for several months, the average...Ch. 7.2 - In a study of the relationship between the Brinell...Ch. 7.2 - A least-squares line is fit to a set of points. If...Ch. 7.2 - Prob. 4ECh. 7.2 - In Galtons height data (Figure 7.1, in Section...Ch. 7.2 - In a study relating the degree of warping, in mm....Ch. 7.2 - Moisture content in percent by volume (x) and...Ch. 7.2 - The following table presents shear strengths (in...Ch. 7.2 - Structural engineers use wireless sensor networks...Ch. 7.2 - The article Effect of Environmental Factors on...Ch. 7.2 - An agricultural scientist planted alfalfa on...Ch. 7.2 - Curing times in days (x) and compressive strengths...Ch. 7.2 - Prob. 13ECh. 7.2 - An engineer wants to predict the value for y when...Ch. 7.2 - A simple random sample of 100 men aged 2534...Ch. 7.2 - Prob. 16ECh. 7.3 - A chemical reaction is run 12 times, and the...Ch. 7.3 - Structural engineers use wireless sensor networks...Ch. 7.3 - Prob. 3ECh. 7.3 - Prob. 4ECh. 7.3 - Prob. 5ECh. 7.3 - Prob. 6ECh. 7.3 - The coefficient of absorption (COA) for a clay...Ch. 7.3 - Prob. 8ECh. 7.3 - Prob. 9ECh. 7.3 - Three engineers are independently estimating the...Ch. 7.3 - In the skin permeability example (Example 7.17)...Ch. 7.3 - Prob. 12ECh. 7.3 - In a study of copper bars, the relationship...Ch. 7.3 - Prob. 14ECh. 7.3 - In the following MINITAB output, some of the...Ch. 7.3 - Prob. 16ECh. 7.3 - In order to increase the production of gas wells,...Ch. 7.4 - The following output (from MINITAB) is for the...Ch. 7.4 - The processing of raw coal involves washing, in...Ch. 7.4 - To determine the effect of temperature on the...Ch. 7.4 - The depth of wetting of a soil is the depth to...Ch. 7.4 - Good forecasting and control of preconstruction...Ch. 7.4 - The article Drift in Posturography Systems...Ch. 7.4 - Prob. 7ECh. 7.4 - Prob. 8ECh. 7.4 - A windmill is used to generate direct current....Ch. 7.4 - Two radon detectors were placed in different...Ch. 7.4 - Prob. 11ECh. 7.4 - The article The Selection of Yeast Strains for the...Ch. 7.4 - Prob. 13ECh. 7.4 - The article Characteristics and Trends of River...Ch. 7.4 - Prob. 15ECh. 7.4 - The article Mechanistic-Empirical Design of...Ch. 7.4 - An engineer wants to determine the spring constant...Ch. 7 - The BeerLambert law relates the absorbance A of a...Ch. 7 - Prob. 2SECh. 7 - Prob. 3SECh. 7 - Refer to Exercise 3. a. Plot the residuals versus...Ch. 7 - Prob. 5SECh. 7 - The article Experimental Measurement of Radiative...Ch. 7 - Prob. 7SECh. 7 - Prob. 8SECh. 7 - Prob. 9SECh. 7 - Prob. 10SECh. 7 - The article Estimating Population Abundance in...Ch. 7 - A materials scientist is experimenting with a new...Ch. 7 - Monitoring the yield of a particular chemical...Ch. 7 - Prob. 14SECh. 7 - Refer to Exercise 14. Someone wants to compute a...Ch. 7 - Prob. 16SECh. 7 - Prob. 17SECh. 7 - Prob. 18SECh. 7 - Prob. 19SECh. 7 - Use Equation (7.34) (page 545) to show that 1=1.Ch. 7 - Use Equation (7.35) (page 545) to show that 0=0.Ch. 7 - Prob. 22SECh. 7 - Use Equation (7.35) (page 545) to derive the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, statistics and related others by exploring similar questions and additional content below.Similar questions
- An article in the Journal of Applied Polymer Science (Vol. 56, pp. 471–476, 1995) studied the effect of the mole ratio of sebacic acid on the intrinsic viscosity of copolyesters.- The data follows: Viscosity 0.45 0.2 0.34 0.58 0.7 0.57 0.55 0.44 Mole ratio 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 (a) Construct a scatter diagram of the data.arrow_forwardThe department of zoology at the Virginia Polytechnic Institute and State University carried out a study to determine if there is a significant difference in the density of organisms in two different stations located in Cedar Run, a secondary river that is located in the river basin. Roanoke. Drainage from a sewage treatment plant and overflow from the Federal Mogul Corporation sedimentation pond enter the flow near the source of the river. The following data give the density measurements, in numbers of organisms per square meter, at the two different collecting stations. Number of organisms per square meter Station 1 Station 2 5030 2800 13700 4670 10730 6890 11400 7720 860 7030 2200 7330 4250 2810 15040 1330 4980 3320 11910 1230 8130 2130 26850 2190 17660 22800 1130 1690 With a significance level of 0.05, can we conclude that the densities are the same in the two…arrow_forward2. Let them classify the following measurement data as high precision or low precision: a. Volume of a liquid: 11.0 cm³, 11.3 cm3, 10.9 cm3, 11.1 cm3 b. Mass of a solid: 25.0 g, 23.0 g, 20.0 g, 28.0g at cr OSgini bns eeA (8) umeniarrow_forward
- Pls help with this homework :arrow_forwardA study was conducted by the Department of Biological Sciences at Virginia Tech to determine if there is a significant difference in the density of organisms at two different stations located on Cedar Run, a secondary stream in the Roanoke River drainage basin. Sewage from a sewage treatment plant and overflow from the Federal Mogul Corporation settling pond enter the stream near its headwaters. The accompanying data give the density measurements, in number of organisms per square meter, at the two collecting stations. Can it be concluded, at the 0.05 level of significance, that the average densities at the two stations are equal? Assume that the observations come from normal populations with different variances. Click the icon to view the data on organisms per square meter. Let sample 1 be the station 1 data and let sample 2 be the station 2 data. State the null and alternative hypotheses. Hoi Hy-H2 = 0 H₁ H1 H2 0 (Type integers or decimals. Do not round.) Find the test statistic. The…arrow_forwardA sample of 18 maple trees in Vermont were treated with one of three amounts of fertilizer. The volume of sap (in ml.) produced by each tree was recorded, with the following results. Sap Volume 74.2 80.4 74.2 81.4 85.9 869 Fertilizer Low Medium 89.0 97.1 95.0 100.2 92.7 96.2 High 82.2 85.5 85.1 92.3 879 95.2 Perform the Tukey-Kramer test to determine which pairs of means, if any, differ. Use the a-0.05 level of significance, The MSE for this data is known to be 49.6256. Round the critical value and test statistic values to two decimal places. Part. 0/4 Part 1 of A Find the critical values. the critical value inarrow_forward
- What is the unit for sleep(answer: hours)? Is its skewness and kurtosis really far enough away from zero to say it is not normal? I was in the chat with two people and they could not assist. I was told to submit my question to a specialtist. Thank youarrow_forwardArtificial hip joints consist of ball and socket. As the joint wears, the ball (head) becomes rough Investigators performed wear tests on metal artificial hip joints. Joints with several different diameters were tested. The Following table presents measurements of head roughness (in nanometers). Diameter Head Roughness 16 0.83 2.25 0.40 2.78 3.23 28 2.72 2.48 3.80 36 6.49 5.32 4.59 a. Because the design is unbalanced, check that the assumption of equal variances is by showing that the largest sample standard deviation is less than twice as large as the smallest one. b. Construct an ANOVA table. c. Can you conclude that the mean roughness varies with diameter? Use the a=0.01 level of significance.arrow_forwardThe efficiency ratio for a steel specimen immersed in a phosphating tank is the weight of the phosphate coating divided by the metal loss (both in mg/ft2). The article “Statistical Process Control of a Phosphate Coating Line” (Wire J. Intl., May 1997: 78–81) gave the accompanying data on tank temperature (x) and efficiency ratio (y).Temp. 170 172 173 174 174 175 176Ratio .84 1.31 1.42 1.03 1.07 1.08 1.04Temp. 177 180 180 180 180 180 181Ratio 1.80 1.45 1.60 1.61 2.13 2.15 .84Temp. 181 182 182 182 182 184 184Ratio 1.43 .90 1.81 1.94 2.68 1.49 2.52Temp. 185 186 188Ratio 3.00 1.87 3.08a. Construct stem-and-leaf displays of both temperature and efficiency ratio, and comment on interesting features.b. Is the value of efficiency ratio completely and uniquely determined by tank temperature? Explain your reasoning.c. Construct a scatterplot of the data. Does it appear that efficiency ratio could be very well predicted by the value of temperature? Explain your reasoning.arrow_forward
- Fluid inclusions are microscopic volumes of fluid that are trapped in rock during rock formation. The article "Fluid Inclusion Study of Metamorphic Gold-Quartz Veins in Northwestern Nevada, U.S.A.: Characteristics of Tectonically Induced Fluid" (S. Cheong, Geosciences Journal, 2002:103-115) describes the geochemical properties of fluid inclusions in several different veins in northwest Nevada. The following table presents data on the maximum salinity (% NaCi by weight) of inclusions in several rock samples from several areas. Salinity Area Humboldt Range Santa Rosa Range 9.2 10.0 11.2 8.8 5.2 6.1 8.3 Ten Mile 7.9 6.7 9.5 7.3 10.4 7.0 Antelope Range Pine Forest Range 6.7 8.4 9.9 10.5 16.7 17.5 15.3 20.0 Can you conclude that the salinity differs among the areas?arrow_forwardIn the 2015 AFC Championship game, there was a charge that the New England Patriots underinflated their footballs for an advantage. The Patriots' opponents during the championship game were the Indianapolis Colts. Measurements of the Colts' footballs were taken. The balls should be inflated to between 12.5 and 13.5 pounds per square inch (psi). The accompanying data consists of six of the eight measurements on the Colts' footballs. Complete parts (a) and (b) below. 12.75, 12.50, 12.15, 12.35, 12.55, 12.30 The test statistic is = (Round to two decimal places as needed.) The p-value is = (Round to three decimal places as needed.) b. Use the data to construct a 95% confidence interval for the mean psi for the Colts' footballs. How does this confidence interval support your conclusion in part (a)? The 95% confidence interval is ___ psi to ___ psi. (Round to two decimal places as needed. Use ascending order.)arrow_forwardAn engineer wants to compare the tensile strengths of steel bars that are produced using a conventional method and an experimental method. (The tensile strength of a metal is a measure of its ability to resist tearing when pulled lengthwise.) To do so, the engineer randomly selectoarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- MATLAB: An Introduction with ApplicationsStatisticsISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons IncProbability and Statistics for Engineering and th...StatisticsISBN:9781305251809Author:Jay L. DevorePublisher:Cengage LearningStatistics for The Behavioral Sciences (MindTap C...StatisticsISBN:9781305504912Author:Frederick J Gravetter, Larry B. WallnauPublisher:Cengage Learning
- Elementary Statistics: Picturing the World (7th E...StatisticsISBN:9780134683416Author:Ron Larson, Betsy FarberPublisher:PEARSONThe Basic Practice of StatisticsStatisticsISBN:9781319042578Author:David S. Moore, William I. Notz, Michael A. FlignerPublisher:W. H. FreemanIntroduction to the Practice of StatisticsStatisticsISBN:9781319013387Author:David S. Moore, George P. McCabe, Bruce A. CraigPublisher:W. H. Freeman
MATLAB: An Introduction with Applications
Statistics
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...
Statistics
ISBN:9781305251809
Author:Jay L. Devore
Publisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...
Statistics
ISBN:9781305504912
Author:Frederick J Gravetter, Larry B. Wallnau
Publisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...
Statistics
ISBN:9780134683416
Author:Ron Larson, Betsy Farber
Publisher:PEARSON
The Basic Practice of Statistics
Statistics
ISBN:9781319042578
Author:David S. Moore, William I. Notz, Michael A. Fligner
Publisher:W. H. Freeman
Introduction to the Practice of Statistics
Statistics
ISBN:9781319013387
Author:David S. Moore, George P. McCabe, Bruce A. Craig
Publisher:W. H. Freeman
Hypothesis Testing using Confidence Interval Approach; Author: BUM2413 Applied Statistics UMP;https://www.youtube.com/watch?v=Hq1l3e9pLyY;License: Standard YouTube License, CC-BY
Hypothesis Testing - Difference of Two Means - Student's -Distribution & Normal Distribution; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=UcZwyzwWU7o;License: Standard Youtube License