The article “Application of Analysis of Variance to Wet Clutch Engagement” (M. Mansouri, M. Khonsari, et al., Proceedings of the Institution of Mechanical Engineers, 2002:117–125) presents the following fitted model for predicting clutch engagement time in seconds (y) from engagement starting speed in m/s (x1), maximum drive torque in N·m (x2), system inertia in kg m2 (x3), and applied force rate in kN/s (x4):
The sum of squares for regression was SSR = 1.08613 and the sum of squares for error was SSE = 0.036310. There were 44 degrees of freedom for error.
- a. Predict the clutch engagement time when the starting speed is 20 m/s, the maximum drive torque is 17 N·m, the system inertia is 0.006 kg·m2, and the applied force rate is 10 kN/s.
- b. Is it possible to predict the change in engagement time associated with an increase of 2 m/s in starting speed? If so, find the predicted change. If not, explain why not.
- c. Is it possible to predict the change in engagement time associated with an increase of 2 N·m in maximum drive torque? If so, find the predicted change. If not, explain why not.
- d. Compute the coefficient of determination R2.
- e. Compute the F statistic for testing the null hypothesis that all the coefficients are equal to 0. Can this hypothesis be rejected?
Want to see the full answer?
Check out a sample textbook solutionChapter 8 Solutions
Connect Access Card for Statistics for Engineers and Scientists
- The article “Monte Carlo Simulation—Tool for Better Understanding of LRFD” (J. of Structural Engr., 1993:1586–1599) suggests that yield strength (ksi) for A36 grade steel is normally distributed with a mean of 50.2 ksi and a standard deviation of 3.8 ksi. What is the probability that the yield strength is greater than 60? (Use 4 decimal places) Show the area of interest in the density curve.arrow_forwardAn article in Technometrics (1999, Vol. 41, pp. 202–211) studied the capability of a gauge by measuring the weights of two sheets of paper. The data follow. Test the hypothesis that the mean weight of the two sheets is equal (μ1−μ2μ1−μ2)against the alternative that it is not (and assume equal variances). Find the t-stat to 3 decimal places.arrow_forwardA study carried out to investigate the distribution of totalbraking time (reaction time plus accelerator-to-brake movementtime, in ms) during real driving conditions at 60 km/hr gave the following summary information on the distributionof times (“A Field Study on Braking ResponsesDuring Driving,” Ergonomics, 1995: 1903–1910):mean 5 535 median 5 500 mode 5 500sd 5 96 minimum 5 220 maximum 5 9255th percentile 5 400 10th percentile 5 43090th percentile 5 640 95th percentile 5 720What can you conclude about the shape of a histogramof this data? Explain your reasoning.arrow_forward
- The article “Monte Carlo Simulation—Tool for Better Understanding of LRFD” (J. of Structural Engr., 1993:1586–1599) suggests that yield strength (ksi) for A36 grade steel is normally distributed with a mean of 50.2 ksi and a standard deviation of 3.8 ksi. What is the probability that the yield strength is at most 45? (Use 4 decimal places). Show the area of interest in the density curve.arrow_forwardTest the hypothesis that the average weekly allowance of female and male ACC 215 students the same, at 5%l evel of significance. Weekly Allowance of Students (Php) Male: 1500 2000 2500 2500 2000 1750 2000 1800 Female:1500 2000 1750 1500 2000 2500 3000 3500 Ho: Ha: α = Decision Rule: Computation: Decision: Conclusion:arrow_forwardThe authors of the article “Predictive Model for PittingCorrosion in Buried Oil and Gas Pipelines”(Corrosion, 2009: 332–342) provided the data on whichtheir investigation was based.a. Consider the following sample of 61 observations onmaximum pitting depth (mm) of pipeline specimensburied in clay loam soil. 0.41 0.41 0.41 0.41 0.43 0.43 0.43 0.48 0.480.58 0.79 0.79 0.81 0.81 0.81 0.91 0.94 0.941.02 1.04 1.04 1.17 1.17 1.17 1.17 1.17 1.171.17 1.19 1.19 1.27 1.40 1.40 1.59 1.59 1.601.68 1.91 1.96 1.96 1.96 2.10 2.21 2.31 2.462.49 2.57 2.74 3.10 3.18 3.30 3.58 3.58 4.154.75 5.33 7.65 7.70 8.13 10.41 13.44Construct a stem-and-leaf display in which the twolargest values are shown in a last row labeled HI.b. Refer back to (a), and create a histogram based oneight classes with 0 as the lower limit of the firstclass and class widths of .5, .5, .5, .5, 1, 2, 5, and 5,respectively.c. The accompanying comparative boxplot fromMinitab shows plots of pitting depth for four differenttypes of soils.…arrow_forward
- A snack food manufacturer estimates that the variance of the number of grams of carbohydrates in servings of its tortilla chips is 1.25. A dietician is asked to test this claim and finds that a random sample of 22 servings has a variance of 1.35. At ⍶ = 0.05 is there enough evidence to reject the manufacturer’s claim?arrow_forwardAn article in Sensors and Actuators A: Physical [“Characterization and Simulation of Avalanche PhotoDiodes for Next-Generation Colliders” (2011, Vol. 172(1), pp. 181–188)] considered an avalanche photodiode (APD) to detect charged particles in a photo. The number of arrivals in each detection window was modeled with a Poisson distribution with a mean depending on the intensity of beam. For one beam intensity, the number of electrons arriving at an APD follows a Poisson dis- tribution with a mean of 1.74 particles per detection window of 200 nanoseconds. a. What is the mean and variance of the time for 100 arrivals?b. What is the probability that the time until the fifth particle arrives is greater than 1.0 nanosecond?arrow_forwardConsider the accompanying data on flexural strength (MPa) for concrete beams of a certain type. 8.3 7.4 7.0 6.8 7.8 9.7 5.0 6.3 6.8 9.0 7.7 7.3 7.4 11.8 6.3 7.7 11.6 7.2 11.3 9.7 10.7 7.0 7.9 8.7 7.9 8.1 6.5 (a) Calculate a point estimate of the mean value of strength for the conceptual population of all beams manufactured in this fashion. [Hint: Σxi = 218.9.] (Round your answer to three decimal places.) MPa(b) Calculate a point estimate of the strength value that separates the weakest 50% of all such beams from the strongest 50%. MPa(c) Calculate a point estimate of the population standard deviation ?. [Hint: Σxi2 = 1851.35.] (Round your answer to three decimal places.) MPa(d) Calculate a point estimate of the proportion of all such beams whose flexural strength exceeds 10 MPa. [Hint: Think of an observation as a "success" if it exceeds 10.] (Round your answer to three decimal places.)(e) Calculate a point estimate of the population coefficient of variation ?/?. (Round…arrow_forward
- Consider the accompanying data on flexural strength (MPa) for concrete beams of a certain type. 5.6 8.9 9.7 6.3 11.3 6.3 7.9 6.5 7.0 9.0 9.7 7.3 11.6 7.7 7.4 7.2 7.8 7.0 7.3 8.2 8.7 6.8 11.8 6.8 7.7 10.7 8.1 (a) Calculate a point estimate of the mean value of strength for the conceptual population of all beams manufactured in this fashion. [Hint: Σxi = 220.3.] (Round your answer to three decimal places.) (b) Calculate a point estimate of the strength value that separates the weakest 50% of all such beams from the strongest 50%. (c) Calculate a point estimate of the population standard deviation ?. [Hint: Σxi2 = 1871.39.] (Round your answer to three decimal places.) (d) Calculate a point estimate of the proportion of all such beams whose flexural strength exceeds 10 MPa. [Hint: Think of an observation as a "success" if it exceeds 10.] (Round your answer to three decimal places.)arrow_forward19. An article in International Journal of Electrical Power & Energy Systems "Stochastic Optimal Load Flow Using a Combined Quasi-Newton and Conjugate Gradient Technique" (1989, Vol. 11(2), pp. 85-93) considered the problem of optimal power flow in electric power systems and included the effects of uncertain variables in the problem formulation. The method treats the system power demand as a normal random variable with 0 mean and unit variance. What is the probability that the power demand is greater than -2 and less than 2? Round your answer to three decimal places (e.g. 98.765).arrow_forwardAn urban community wants to show that the incidence of breast cancer is higher in their locality than in a neighboring rural area. (PCB levels were found to be higher in the soil of the urban community). If you find that in the urban community 20 out of 200 adult women have breast cancer and that in the rural community 10 out of 150 adult women have it, could you conclude, at a significance level of 0.05, that breast cancer is more prevalent in the urban community?1. The parameter of interest is:2. The hypotheses for this test are:3. The calculated test statistic is:4. The critical region is:5. Draw the critical region (make decision):6. It can be concluded that:arrow_forward
- MATLAB: An Introduction with ApplicationsStatisticsISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons IncProbability and Statistics for Engineering and th...StatisticsISBN:9781305251809Author:Jay L. DevorePublisher:Cengage LearningStatistics for The Behavioral Sciences (MindTap C...StatisticsISBN:9781305504912Author:Frederick J Gravetter, Larry B. WallnauPublisher:Cengage Learning
- Elementary Statistics: Picturing the World (7th E...StatisticsISBN:9780134683416Author:Ron Larson, Betsy FarberPublisher:PEARSONThe Basic Practice of StatisticsStatisticsISBN:9781319042578Author:David S. Moore, William I. Notz, Michael A. FlignerPublisher:W. H. FreemanIntroduction to the Practice of StatisticsStatisticsISBN:9781319013387Author:David S. Moore, George P. McCabe, Bruce A. CraigPublisher:W. H. Freeman