SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
10th Edition
ISBN: 9781260163155
Author: BUDYNAS
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 9, Problem 37P
To determine
The pattern of the weld.
The electrode number.
The length of the weld.
The leg size of the weld.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The figure shows a solid 2-inch diameter roller that is attached to the wall by means of a permanent clamping. Specify the weld size for the case where the maximum allowable shear stress is 18 kpsi.
All-round fillet weld with a steel beam weld thickness a=6 mm and weld seam length shown in the figure welded to the steel column. Forces of 2 kN and 3 kN from the beam end in the horizontal and vertical directions, respectively has been applied. The smallest yield strength of the weld material so that the steel structure has a safety of 2.5. Calculate according to von Mises static damage theory ?
In the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E= 70GPa rod within a closed-end bronze of L= 610mm, A= 1206mm^2 and E= 100GPa tube. Before the load P is applied, there is a clearance of 2mm between the rod flange at B and the tube closure at A. After load P is applied, the solid aluminum alloy rod stretches enough so that flange B contacts the closed end of the tube at A. If the load applied to the lower end of the aluminum rod is P= 345KN, calculate:A. The normal stress in bronze tube, in MPa.B. The elongation of bronze tube, in mm.
Chapter 9 Solutions
SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
Ch. 9 - 91 to 94 The figure shows a horizontal steel bar...Ch. 9 - 91 to 94 The figure shows a horizontal steel bar...Ch. 9 - 91 to 94 The figure shows a horizontal steel bar...Ch. 9 - 91 to 94 The figure shows a horizontal steel bar...Ch. 9 - 95 to 98 For the weldments of Probs. 91 to 94, the...Ch. 9 - 95 to 98 For the weldments of Probs. 91 to 94, the...Ch. 9 - 95 to 98 For the weldments of Probs. 91 to 94, the...Ch. 9 - 95 to 98 For the weldments of Probs. 91 to 94, the...Ch. 9 - 99 to 912 The materials for the members being...Ch. 9 - Prob. 10P
Ch. 9 - Prob. 11PCh. 9 - 99 to 912 The materials for the members being...Ch. 9 - 913 to 916 A steel bar of thickness h is welded to...Ch. 9 - 913 to 916 A steel bar of thickness h is welded to...Ch. 9 - 913 to 916 A steel bar of thickness h is welded to...Ch. 9 - Prob. 16PCh. 9 - Prob. 17PCh. 9 - 917 to 920 A steel bar of thickness h, to be used...Ch. 9 - 917 to 920 A steel bar of thickness h, to be used...Ch. 9 - 917 to 920 A steel bar of thickness h, to be used...Ch. 9 - Prob. 21PCh. 9 - 921 to 924 The figure shows a weldment just like...Ch. 9 - Prob. 23PCh. 9 - Prob. 24PCh. 9 - 9-25 to 9-28 The weldment shown in the figure is...Ch. 9 - 9-25 to 9-28 The weldment shown in the figure is...Ch. 9 - Prob. 27PCh. 9 - 925 to 928 The weldment shown in the figure is...Ch. 9 - The permissible shear stress for the weldment...Ch. 9 - Prob. 30PCh. 9 - 9-30 to 9-31 A steel bar of thickness h is...Ch. 9 - In the design of weldments in torsion it is...Ch. 9 - Prob. 33PCh. 9 - Prob. 34PCh. 9 - The attachment shown carries a static bending load...Ch. 9 - The attachment in Prob. 935 has not had its length...Ch. 9 - Prob. 37PCh. 9 - Prob. 39PCh. 9 - Prob. 40PCh. 9 - Prob. 42PCh. 9 - 9-43 to 9-45 A 2-in dia. steel bar is subjected to...Ch. 9 - 9-43 to 9-45 A 2-in dia. steel bar is subjected to...Ch. 9 - Prob. 45PCh. 9 - Prob. 46PCh. 9 - Find the maximum shear stress in the throat of the...Ch. 9 - The figure shows a welded steel bracket loaded by...Ch. 9 - Prob. 49PCh. 9 - Prob. 50PCh. 9 - Prob. 51PCh. 9 - Brackets, such as the one shown, are used in...Ch. 9 - For the sake of perspective it is always useful to...Ch. 9 - Hardware stores often sell plastic hooks that can...Ch. 9 - For a balanced double-lap joint cured at room...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The loads shown are service loads. A36 steel and 5⁄8-inchdiameter, Group A bolts will be used. If slip is permissible, how many bolts are required? Each bolt centerline shown represents a row of bolts in the direction of the width of the plates.arrow_forwardA circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.arrow_forward(D) Seven circular cross-section rivets (Dia.=16 mm) are used to fix a lap joint of steel plates under single shear action. If the rivets are made from Aluminium (E=80 GPa) and the plates under tension of 15 kN. Solve this problem to show weather this joint is safe or not. Suppose all the rivets have equal load share.arrow_forward
- appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).arrow_forwardA circular steel bar 50 mm diameter and 200 mm long is welded perpendicularly to a steel plate to form a cantilever to be loaded with 5 kN at the free end. Determine the size of the weld, assuming the allowable stress in the weld as 100MPa.arrow_forwardThe figures below show a formed sheet-steel bracket. The total distributed load “W” on the bracket is 20 kN. It is secured to the support with two grade 5.8 bolts. The joint constant is C=0.183, and the bolts are preloaded to 70 percent of the proof load. The dimensions of the top flange are the same as the mounting flange.a) Find the external loads (P1 and P2) carried by upper and bottom bolts respectively if both resist the moment?b) Find the upper bolt diameter by ignoring direct shear load and determine/select a standard metric bolt size with a pitch for a design factor of 1,4.c) Is there any need to enlarge 5 mm dia. holes in the bracket?arrow_forward
- What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?arrow_forwardGiven a 2meter Wide Flange steel compression member with A=4,513mm2, Ix=86,630,006mm4 and Iy=3,824,544mm4 with Fy = 345MPa. Calculate the critical buckling stress in MPa if both ends are fixed or rigid. Express your answer in 2 decimal places.arrow_forwardFigure below shows a bolted and doweled joint eccentrically loaded in shear. The bolts and dowel pins are used to connect the two parts. The shear loads are taken by the dowel pins, the sizes of which are: dA = 0.375 in, dB = 0.375 in, dC = 0.250 in, dD = 0.250 in, dE = 0.250 in. Dowels with diameters of zero are not present. Though the figure shows 5 dowel pins, that is not the case if some dowels are with zero diameters. Assume that a = 4 in, b = 4 in, l = 10 in, P = 2500 lb. Suppose that all of the dowels will take all the shear loading and will share the load equally. Assume that one part is allowed to rotate slightly about the centroid with respect to the other part. Part A Find the magnitude of the total shear force acting on dowel A. Express your answer in pounds to three significant figures. Part B Find the direction angle of the total shear force acting on dowel A measured counterclockwise from the positive x axis. Express your answer in degrees to three…arrow_forward
- Calculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ?Y=300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ?Y=300 MPa, n=2 - FOS for pin/bearing and ?Allow=300 MPa for bearing).arrow_forwardA circularbeam, 50 mm in diameter, is welded to support using a fillet weld as in the figure. Determinethe size of the weld, if the permissible shear stress is 100 N/mm2.arrow_forwardA welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find thesize of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm2arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License