Explanation Consider the system is in steady state. Hence, the inlet and exit mass flow rates are equal. The mass flow rate of feed water ( m ˙ f w ) is as follows. m ˙ 1 = m ˙ 2 = m ˙ f w The mass flow rate of steam ( m ˙ s ) is as follows. m ˙ 3 = m ˙ 4 = m ˙ s Write the energy rate balance equation for one inlet and one outlet system. [ Q ˙ 1 + W ˙ 1 + m ˙ ( h 1 + V 1 2 2 + g z 1 ) ] − [ Q ˙ 2 + W ˙ 2 + m ˙ ( h 2 + V 2 2 2 + g z 2 ) ] = Δ E ˙ system (I) Here, the rate of heat transfer is Q ˙ , the rate of work transfer is W ˙ , the enthalpy is h and the velocity is V , the gravitational acceleration is g , the elevation from the datum is z and the rate of change in net energy of the system is Δ E ˙ system ; the suffixes 1 and 2 indicates the inlet and outlet of the system. The system is at steady state. Hence, the rate of change in net energy of the system becomes zero. Δ E ˙ system = 0 Neglect the work transfer, heat transfer to the surrounding, potential and kinetic energies. The Equations (I) reduced as follows for feed water. [ 0 + 0 + m ˙ 1 ( h 1 + 0 + 0 ) ] − [ 0 + 0 + m ˙ 2 ( h 2 + 0 + 0 ) ] = 0 m ˙ 1 h 1 − m ˙ 2 h 2 = 0 m ˙ 1 h 1 = m ˙ 2 h 2 (II) The Equations (I) reduced as follows for steam. [ 0 + 0 + m ˙ 3 ( h 3 + 0 + 0 ) ] − [ 0 + 0 + m ˙ 4 ( h 4 + 0 + 0 ) ] = 0 m ˙ 3 h 3 − m ˙ 4 h 4 = 0 m ˙ 3 h 3 = m ˙ 4 h 4 (III) Combining Equation (II) and (III). m ˙ 1 h 1 + m ˙ 3 h 3 = m ˙ 2 h 2 + m ˙ 4 h 4 m ˙ 2 h 2 − m ˙ 1 h 1 = m ˙ 3 h 3 − m ˙ 4 h 4 Substitute m ˙ f w for m ˙ 1 , m ˙ 2 and m ˙ s for m ˙ 3 , m ˙ 4

9th Edition

ISBN: 9781259822674

Author: Yunus A. Cengel Dr., Michael A. Boles

Publisher: McGraw-Hill Education

See similar textbooks

Videos

Question

Chapter 10.9, Problem 94RP

To determine

The rate at which bleed steam is required.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 10.9, Problem 93P

Chapter 10.9, Problem 95RP

Students have asked these similar questions

Consider a reheat-regenerative vapor power cycle with two feedwater heaters, a closed feedwater heater and an open feedwater heater. Steam enters the first turbine at 8000 kPa and 480oC and expands to 700 kPa. The steam is reheated to 440oC before entering the second turbine, where it expands to the condenser pressure of 8 kPa. Steam is extracted from the first turbine at 2000 kPa and fed to the closed feedwater heater. The feedwater leaves the closed heater at 205oC and 8000 kPa and enters the boiler to complete the cycle. The condensate from the closed feedwater heater is throttled into the open feedwater heater. Steam extracted from the second turbine at 300 kPa is also fed into the open feedwater heater, which operates at 300 kPa. The stream exiting the open feedwater heater is saturated liquid at 300 kPa. The net power output of the cycle is 100 MW. If the working fluid experiences no irreversibilities as it passes through the turbines and pumps, determine: (a) mass flowrate of…

Steam enters the turbine of a power plant operating on the Rankine cycle at 3300 kPa and exhausts at 50 kPa. To show the effect of superheating on the performance of the cycle, calculate the thermal efficiency of the cycle and the quality of the exhaust steam from the turbine for turbine-inlet steam temperatures of 450, 500, 5500C.

Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 5400 kPa, the reheat section 1100 kPa, and the condenser at 10 kPa. The mixture quality at the exit of both turbines is 94 %. Determine the following values. (1) The specific enthalpy at the exit of the high-pressure turbine. (2) The specific entropy at the exit of the high-pressure turbine. (3) The temperature at the inlet of the high-pressure turbine. (4) The temperature at the inlet of the low-pressure turbine. (5) The thermal efficiency of the cycle.

Chapter 10 Solutions

Thermodynamics: An Engineering Approach

Ch. 10.9 - Why is the Carnot cycle not a realistic model for...Ch. 10.9 - Why is excessive moisture in steam undesirable in...Ch. 10.9 - A steady-flow Carnot cycle uses water as the...Ch. 10.9 - A steady-flow Carnot cycle uses water as the...Ch. 10.9 - Consider a steady-flow Carnot cycle with water as...Ch. 10.9 - Water enters the boiler of a steady-flow Carnot...Ch. 10.9 - What four processes make up the simple ideal...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...Ch. 10.9 - Consider a simple ideal Rankine cycle with fixed...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The rate at which bleed steam is required.

Solution Summary: The author explains the rate at which bleed steam is required and the energy rate balance equation for one inlet and one outlet system.

Videos

The rate at which bleed steam is required.

Want to see the full answer?

Chapter 10 Solutions