Mechanics of Materials - With MindTap
9th Edition
ISBN: 9781337581042
Author: GOODNO
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 11, Problem 11.3.16P
.16 Three identical, solid circular rods, each of radius r and length L, are placed together to form a compression member (see the cross section shown in the figure).
Assuming pinned-end conditions, determine the critical load Pcr
- The rods act independently as individual columns.
What is the effect on the critical load when the rods act as a single member?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
QUESTION 3: Square profile made of hollow 1045 steel, with a
length of 6 meters with a cross-sectional area of 40x40 mm
and a wall thickness of 4 mm, is subjected to an axial tensile
load of "6" KN from both ends.
remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate
%3D
%3D
the final length of the rod under this tensile load in "mm".
(b)
A steel strut of height 2 m, and cross-section 50 mm x 24 mm, is subject
to an axial compressive load. The strut is supported at both ends as
shown in Figure 2. The pin allows rotation about the y-y axis only.
(i)
(ii)
(iii)
The steel used in the manufacture of the strut has an elastic modulus of
205 GPa and a yield stress of 240 MPa.
2m
A
LOAD
puyu
Ţ
A
L.
LOAD
50 mm
IN
L.
24 mm
ENLARGED SECTION A-A
Figure 2: Support conditions and cross-section of steel strut
Describe the strut's end fixing conditions about the x-x and y-y axes.
Calculate the strut's buckling load according to Euler Formula.
Sketch the relationship of the slenderness ratio and buckling stress for the
strut about the x-x axis. Critically comment on the suitability of the Euler
equation for estimating the maximum compressive load the strut can
support.
Question 3: Find the extension in mild steel wire of 10 mm in diameter and 1.6 m long, the wire is
subjected to an axial tensile load of 10 kN. (Consider E= 200 GPA).
Chapter 11 Solutions
Mechanics of Materials - With MindTap
Ch. 11 - A rigid bar of length L is supported by a linear...Ch. 11 - The figure shows an idealized structure consisting...Ch. 11 - -2-3. Two rigid bars are connected with a...Ch. 11 - Repeat Problem 11.2-3 assuming that R= 10 kN ·...Ch. 11 - The figure shows an idealized structure consisting...Ch. 11 - An idealized column consists of rigid bar ABCD...Ch. 11 - An idealized column is made up of rigid segments...Ch. 11 - The figure shows an idealized structure consisting...Ch. 11 - The figure shows an idealized structure consisting...Ch. 11 - The figure shows an idealized structure consisting...
Ch. 11 - The figure shows an idealized structure consisting...Ch. 11 - Rigid column ABCD has an elastic support at B with...Ch. 11 - An idealized column is made up of rigid bars ABC...Ch. 11 - An idealized column is composed of rigid bars ABC...Ch. 11 - Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25...Ch. 11 - An idealized column is composed of rigid bars ABC...Ch. 11 - Column AB has a pin support at A,a roller support...Ch. 11 - Slender column ABC is supported at A and C and is...Ch. 11 - Calculate the critical load PCTfor a W 8 × 35...Ch. 11 - Solve the preceding problem for a W 250 × 89 steel...Ch. 11 - Solve Problem 11.3-3 for a W 10 × 45 steel column...Ch. 11 - A horizontal beam AB is pin-supported at end A and...Ch. 11 - A column ABC is supported at ends A and C and...Ch. 11 - Find the controlling buckling load (kN) for the...Ch. 11 - A column, pinned at top and bottom, is made up of...Ch. 11 - Repeat Problem 11.3-9. Use two C 150 × 12.2 steel...Ch. 11 - A horizontal beam AB is pin-supported at end A and...Ch. 11 - -12 A horizontal beam AB is supported at end A and...Ch. 11 - A horizontal beam AB has a sliding support at end...Ch. 11 - A slender bar AB with pinned ends and length L is...Ch. 11 - A rectangular column with cross-sectional...Ch. 11 - .16 Three identical, solid circular rods, each of...Ch. 11 - Three pinned-end columns of the same material have...Ch. 11 - A long slender column ABC is pinned at ends A and...Ch. 11 - The roof over a concourse at an airport is...Ch. 11 - The hoisting arrangement for lifting a large pipe...Ch. 11 - A pinned-end strut of aluminum (E = 10,400 ksi)...Ch. 11 - The cross section of a column built up of two...Ch. 11 - The truss ABC shown in the figure supports a...Ch. 11 - A truss ABC supports a load W at joint B, as shown...Ch. 11 - An S6 × 12.5 steel cantilever beam AB is supported...Ch. 11 - The plane truss shown in the figure supports...Ch. 11 - A space truss is restrained at joints O, A,B, and...Ch. 11 - A fixed-end column with circular cross section is...Ch. 11 - A cantilever aluminum column has a square tube...Ch. 11 - An aluminum pipe column (E = 10,400 ksi) with a...Ch. 11 - Solve the preceding problem for a steel pipe...Ch. 11 - A wide-flange steel column (E = 30 × l06 psi) of...Ch. 11 - Prob. 11.4.6PCh. 11 - The upper end of a WE × 21 wide-flange steel...Ch. 11 - A vertical post AB is embedded in a concrete...Ch. 11 - The horizontal beam ABC shown in the figure is...Ch. 11 - The roof beams of a warehouse are supported by...Ch. 11 - Determine the critical load Pcrand the equation of...Ch. 11 - A fixed-pinned column is a W310 × 21 steel shape...Ch. 11 - Find the Controlling buckling load (kips) for the...Ch. 11 - Prob. 11.4.14PCh. 11 - A rigid L-shaped frame is supported by a steel...Ch. 11 - An aluminum tube AB with a circular cross section...Ch. 11 - The frame ABC consists of two members AB and BC...Ch. 11 - An aluminum bar having a rectangular cross section...Ch. 11 - ‘11.5-2 A steel bar having a square cross section...Ch. 11 - A simply supported slender column is subjected to...Ch. 11 - A brass bar of a length L = 0.4 m is loaded at end...Ch. 11 - Determine the bending moment M in the pinned-end...Ch. 11 - Plot the load-deflection diagram for a pinned-end...Ch. 11 - Solve the preceding problem for a column with e =...Ch. 11 - A wide-flange member (W200 × 22.5) is compressed...Ch. 11 - A wide-f hinge member (W 10 × 30) is compressed by...Ch. 11 - Solve the preceding problem (W 250 × 44.8) if the...Ch. 11 - The column shown in the figure is fixed at the...Ch. 11 - An aluminum box column with a square cross section...Ch. 11 - Solve the preceding problem for an aluminum column...Ch. 11 - A steel post /t if with a hollow circular cross...Ch. 11 - A frame ABCD is constructed of steel wide-flange...Ch. 11 - A steel bar has a square cross section of width b...Ch. 11 - ]11.6-2 A brass bar (E = 100 GPa) with a square...Ch. 11 - A square aluminum bar with pinned ends carries a...Ch. 11 - A pinned-and column of a length L = 2A m is...Ch. 11 - A pinned-end strut of a length L = 5.2 ft is...Ch. 11 - A circular aluminum tube with pinned ends supports...Ch. 11 - A steel W 12 × 35 column is pin-supported at the...Ch. 11 - A steel W 310 x 52 column is pin-supported at the...Ch. 11 - A steel column (E = 30 x 103 ksi) with pinned ends...Ch. 11 - A W410 × S5 steel column is compressed by a force...Ch. 11 - A steel column ( E = 30 X 103 ksi) that is fixed...Ch. 11 - AW310 × 74 wide-flange steel column with length L...Ch. 11 - A pinned-end column with a length L = 18 ft is...Ch. 11 - The wide-flange, pinned-end column shown in the...Ch. 11 - A W14 × 53 wide-flange column of a length L = 15...Ch. 11 - A wide-flange column with a bracket is fixed at...Ch. 11 - Determine the allowable axial load Pallowa W 10 X...Ch. 11 - Determine the allowable axial load Pallowfor a W...Ch. 11 - Determine the allowable axial load Pallowfor a W...Ch. 11 - Select a steel wide-flange column of a nominal...Ch. 11 - Prob. 11.9.5PCh. 11 - Select a steel wide-flange column of a nominal...Ch. 11 - Prob. 11.9.7PCh. 11 - Determine the allowable axial load Pallowfor a...Ch. 11 - Determine the allowable axial load Pallowfor a...Ch. 11 - Determine the allowable axial load Pallowfor a...Ch. 11 - -11 Determine the maximum permissible length...Ch. 11 - Determine the maximum permissible length Lmaxfor a...Ch. 11 - A steel pipe column with pinned ends supports an...Ch. 11 - The steel columns used in a college recreation...Ch. 11 - A W8 × 28 steel wide-flange column with pinned...Ch. 11 - Prob. 11.9.16PCh. 11 - Prob. 11.9.17PCh. 11 - Prob. 11.9.18PCh. 11 - Prob. 11.9.19PCh. 11 - Prob. 11.9.20PCh. 11 - Prob. 11.9.21PCh. 11 - An aluminum pipe column (alloy 2014-T6) with...Ch. 11 - Prob. 11.9.23PCh. 11 - Prob. 11.9.24PCh. 11 - Prob. 11.9.25PCh. 11 - Prob. 11.9.26PCh. 11 - Prob. 11.9.27PCh. 11 - Prob. 11.9.28PCh. 11 - Prob. 11.9.29PCh. 11 - Prob. 11.9.30PCh. 11 - A wood column with, a rectangular cross section...Ch. 11 - Prob. 11.9.32PCh. 11 - Prob. 11.9.33PCh. 11 - A square wood column with side dimensions b (see...Ch. 11 - A square wood column with side dimensions b (see...Ch. 11 - Prob. 11.9.36P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A bar ABCD shown in figure below consists of three sections: AB is of 42 mm diameter and 80 mm long, BC is 65 mm square and 145 mm long, and CD is a circular section of 52 mm diameter and 70 mm long. What will be the total extension of the bar under the tensile load of 300 kN? EAB=185 GN/m?, EBc-200 GN/m?, and Ecp=178 GN/m?. (Square eross section) (Circular cross seetion) (Circular cross section) 300 kN 300 kN 65 mm 52 mm 80 mm 70 mmarrow_forward.A 5-mm thick mild steel plate is used to form a hollow column of 60 mm outside diameter. The column length is 1.2 m. Calculate the crippling load using Johnson’s Parabolic formula. Take modulus of elasticity and yield strength as 206 GPa and 330 MPa, respectively. Assume one end is hinged and the other end fixed.218212 N176745 N930094 N263252 Narrow_forwardanswer with complete solution please thank youarrow_forward
- Can't figure this outarrow_forwardA composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy cylinder of the same length of 1.5m and whose internal and external diameters are 20 mm and 25 mm respectively. The column is then subjected to an axial load of 50 kN. Modulus of elasticity for steel and alloy is 200000MPA and 70000MPA respectively. Which of the following gives deformation of steel? Select one: a. 2.0 mm b. 3.0 mm C. 4.0 mm d. 1.0 mmarrow_forwardQuestion 4 of 10 -/ 10 Current Attempt in Progress AWT205 x 30 structural steel section (see Appendix B for cross-sectional properties) is used for a 6.6 mcolumn. Assume pinned connections at each end of the column. Determine: (a) the slenderness ratio. (bi the Euler buckling load. Use E- 200 GPa for the steel. (c) the asdal stress in the columnwhen the Euler load is applied. Part 1 Use Appendix B to lookup the cross-sectional area, the area moment of inertia, and the radius of gyration for a WT205 x 30 structural steel section. Answer A x 10 mm mm x 10 mm mmarrow_forward
- a. Two brass rods used as compression members, each of 3-m effective length with pin end, have the cross sections shown in Figure Q5a. Determine the wall thickness of the hollow square rod for which the rods have the same critical buckling load. UZA O 40 mm 60 mm Figure Q5a 60 mm MALAYSIA UTM ERSITI TEKNO UNIVERSITI TEKNOLL 01arrow_forwardThe assembly consists of two red brass C83400 copper rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The supports at A, C and Fare rigid. Modul of elasticy for the copper is Ecopper = 101 GPa. Modul of elasticity for the steel is Esteel = 193 GPa. (Figure 1) Figure Part A OAB = Submit Part B OCD = Submit Part C Value μÅ Request Answer Determine the average normal stress developed in the rod AB. Express your answer to three significant figures and include the appropriate units. TEF Value μA Request Answer Submit Units 19 Units FA Determine the average normal stress developed in the rod CD. Express your answer to three significant figures and include the appropriate units. O μА -300 mm- Value 30 mm 30 mm Request Answer ? B G ? E 450 mm 40 kN Determine the average normal stress developed in the rod EF. Express your answer to three significant figures and include the appropriate units. 40 kN 40 mm Units MELL < 1 of 1 ?arrow_forwardb) Two hollow circular rods are welded together at B and loaded as shown in Figure 5. Load P; acting at the top is equal to 16 kN. The load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the rods are das = 30 mm, tas = 12 mm, dec = 60 mm, and tec = 9 mm, respectively. Given that the lower part of the rod has the same compressive stress as the upper rod. Examine the required magnitude for load Pz. P1 tAB -dAB |P2 B -dBC IBC Figure 5arrow_forward
- A bar of length 5 m is subjected to an axial tensile out of 100 KN The bar is 25 min diameter for 2 mof its length 30 mm diameter for I mor its length, and 20 mm diameter for the remaining 2 m of its length, Taking E= 2 x 10' Calculate the total increase in length of the bur.arrow_forwardQuestion 4 of 5 A column with a length of 6 m is fixed at one end and free at the other end. The column is made of a steel I-beam whose web is 250 mm by 9 mm thick and flanges are 175 mm wide by 15 mm thick. The Modulus of Elasticity for steel is 200 GPa. a. Find the Euler Load for this Column. b. If the FS is 3.5, what is the maximum allowable load for this column? Answer using this format: A. GIVEN B. FORMULA C. SOLUTION with unit analysis D. FINAL ANSWERarrow_forwardA sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License