Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 2, Problem D2.71P
a.
To determine
To show: The circuit can be implemented as difference amplifier of the provided gain.
b.
To determine
To show: The circuit can be implemented as a single-ended amplifier with the following gains and comments on the relative merits of each gain by considering the given condition.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The following Operational Amplifier circuit is given. Analyze the circuit
carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps.
Calculate the first stage output voltage Vx and then the output voltage at the output of
the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the
power absorbed by the resistor R7. The resistors: R2 = R4 =100KW. R1 = R3 = 10W,
R5 = 10W, R6 = 90 KW. and R5 = 10W. The load resistor R7 = 10KW. The current
source; I1 = 100μA and V2 = 1V.
Referenced instrumentation amplifier
The diagram above represents a 2-amp instrumentation amplifier with a reference input (Vref). The equation that best defines the relationship between the inputs and outputs of the circuit is:
For the circuit given,
a) Find VO in terms of V1 and V2. b) If V1=2V and V2=6V, find VO. c) If the op-amp supplies are ±12V, and V1=4V, what is the allowable range of V2?
Chapter 2 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 2.1 - Prob. 2.1ECh. 2.1 - Prob. 2.2ECh. 2.1 - Prob. 2.3ECh. 2.2 - Prob. D2.4ECh. 2.2 - Prob. 2.5ECh. 2.2 - Prob. 2.6ECh. 2.2 - Prob. D2.7ECh. 2.2 - Prob. D2.8ECh. 2.3 - Prob. 2.9ECh. 2.3 - Prob. 2.10E
Ch. 2.3 - Prob. D2.11ECh. 2.3 - Prob. 2.12ECh. 2.3 - Prob. 2.13ECh. 2.3 - Prob. 2.14ECh. 2.4 - Prob. 2.15ECh. 2.4 - Prob. D2.16ECh. 2.4 - Prob. 2.17ECh. 2.5 - Prob. 2.18ECh. 2.5 - Prob. D2.19ECh. 2.5 - Prob. D2.20ECh. 2.6 - Prob. 2.21ECh. 2.6 - Prob. 2.22ECh. 2.6 - Prob. 2.23ECh. 2.6 - Prob. 2.24ECh. 2.6 - Prob. 2.25ECh. 2.7 - Prob. 2.26ECh. 2.7 - Prob. 2.27ECh. 2.7 - Prob. 2.28ECh. 2.8 - Prob. 2.29ECh. 2.8 - Prob. 2.30ECh. 2 - Prob. 2.1PCh. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Prob. 2.4PCh. 2 - Prob. 2.5PCh. 2 - Prob. 2.6PCh. 2 - Prob. 2.7PCh. 2 - Prob. 2.8PCh. 2 - Prob. 2.9PCh. 2 - Prob. 2.10PCh. 2 - Prob. 2.11PCh. 2 - Prob. D2.12PCh. 2 - Prob. D2.13PCh. 2 - Prob. D2.14PCh. 2 - Prob. 2.15PCh. 2 - Prob. 2.16PCh. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Prob. 2.19PCh. 2 - Prob. D2.20PCh. 2 - Prob. 2.21PCh. 2 - Prob. 2.22PCh. 2 - Prob. 2.23PCh. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - Prob. D2.26PCh. 2 - Prob. 2.27PCh. 2 - Prob. 2.28PCh. 2 - Prob. D2.29PCh. 2 - Prob. 2.30PCh. 2 - Prob. 2.31PCh. 2 - Prob. 2.32PCh. 2 - Prob. D2.33PCh. 2 - Prob. D2.34PCh. 2 - Prob. D2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. D2.37PCh. 2 - Prob. D2.38PCh. 2 - Prob. D2.39PCh. 2 - Prob. D2.40PCh. 2 - Prob. D2.41PCh. 2 - Prob. D2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. D2.44PCh. 2 - Prob. D2.45PCh. 2 - Prob. D2.46PCh. 2 - Prob. D2.47PCh. 2 - Prob. D2.48PCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. D2.51PCh. 2 - Prob. D2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. D2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. D2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. D2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. D2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. D2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. D2.76PCh. 2 - Prob. 2.77PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. D2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. D2.82PCh. 2 - Prob. D2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. D2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. D2.92PCh. 2 - Prob. D2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. D2.99PCh. 2 - Prob. D2.100PCh. 2 - Prob. 2.101PCh. 2 - Prob. 2.102PCh. 2 - Prob. 2.103PCh. 2 - Prob. 2.104PCh. 2 - Prob. 2.105PCh. 2 - Prob. 2.106PCh. 2 - Prob. 2.107PCh. 2 - Prob. 2.108PCh. 2 - Prob. 2.109PCh. 2 - Prob. 2.110PCh. 2 - Prob. 2.111PCh. 2 - Prob. 2.112PCh. 2 - Prob. 2.113PCh. 2 - Prob. 2.114PCh. 2 - Prob. 2.115PCh. 2 - Prob. D2.116PCh. 2 - Prob. D2.117PCh. 2 - Prob. D2.118PCh. 2 - Prob. 2.119PCh. 2 - Prob. 2.120PCh. 2 - Prob. 2.121PCh. 2 - Prob. 2.122PCh. 2 - Prob. 2.123PCh. 2 - Prob. 2.124PCh. 2 - Prob. 2.125PCh. 2 - Prob. 2.126PCh. 2 - Prob. D2.127P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The circuit utilizes an ideal op amp 1)Find I1, I2, I3, IL and Vx. 2) If VO is not to be lower than -6V, find the maximum allowed value for RL. 3) If RL is varied in the range 200Ω to 600Ω, what is the corresponding change in IL and VO?arrow_forwardNeed Help for this question please, Thank you For the circuit in Figure Q2(b), an input wave is shown. Given that VCC = +4 V,VEE = −4 V, R = 10 kΩ, and C = 10 nF. Assuming C is neutral at initially andthe maximum output swing of op amp is 1 V away from each of the two powersupplies. Sketch its output waveform with complete labeling of all voltagelevels, showing all workings.arrow_forwardConsider the following op amp configuration.(a) Choose R2 such that the ideal voltage gain is Av = 40dB and draw the amplifier’stransfer characteristic.(b) Find the amplifier’s input and output resistances.(c) If the op amp’s internal gain is Ao = 120dB, what is the expected voltage gain ofthe entire network?arrow_forward
- The circuit in Figure below uses an ideal Op Amp. (a) Find I1, I2, I3 and Vx. (b) Assuming that Vo must not be less than –13 V, find the maximum expected value for RL. (c) If RL is varied in the range from 100 Ω to 1kΩ, what will be the corresponding range in IL and in VO?arrow_forwardAssume that the ideal op amp in the circuit seen is operating in its linear region, What happens if R1→∞ and R2→0?arrow_forwardThe op amp in the circuit shown is ideal Find the range of values for vs such that vo does not saturate and the op amp remains in its linear region of operation.arrow_forward
- The op amps as shown are ideal. What are the nominal, minimum, and maximum values of the voltage gain, input resistance, and output resistance of the overall amplifier if all the resistors have 2 percent tolerances?arrow_forwardAssume that the ideal op amp in the circuit seen is operating in its linear region, Show that vo=[(R1+R2)/R1]vs.arrow_forwardThe noninverting amplifier shown is built with an op amp having an input resistance of 2MΩ and an open-loop gain of 90 dB. What is the amplifier input resistance if R1 = 20 kΩ and R2 =510 kΩ?arrow_forward
- Specify RfRf, given that vi = 19 V *The resistor Rf in the circuit in the figure is adjusted until the ideal op amp saturates.*arrow_forward1. Find the Thévenin equivalent circuit with respect to the output terminals a, b for the inverting amplifier shown. The dc signal source has a value of 880 mV. The op amp has an input resistance of 500 kΩ, an output resistance of 2 kΩ, and an openloop gain of 100,000. 2. What is the output resistance of the inverting amplifier? 3. What is the resistance (in ohms) seen by the signal source vs when the load at the terminals a, b is 330 Ω?arrow_forwardSelect true or false for 1 and 21 Op amp component is temperature limited due to maximum output current2 The input offset voltage affects the value of the opamp output and is caused by internal non-idealities in the transistors and resistors. 3 What is the use of an op amp in voltage follower? Select one:a. It is the ideal bridge to couple any stages without affecting the voltage.b. It is ideal for maximum power transferc. Allows a small signal to be amplified with high gaind. voltage attenuation 4. It allows to eliminate the problem of variability in the gain parameter of the circuit:Select one:a. The load RLb. High input impedancec. feedback loopd. decoupling capacitors 5 Complete: The output current is limited due to the _____ that the opamp can handle, while the ______ is limiting due to the maximum bias level supported by the transistor.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
Electrical Engineering: Ch 5: Operational Amp (2 of 28) Inverting Amplifier-Basic Operation; Author: Michel van Biezen;https://www.youtube.com/watch?v=x2xxOKOTwM4;License: Standard YouTube License, CC-BY