Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 2, Problem 2.85P
To determine
To sketch:The output waveform for the given input.
Also the number of pulses required for a given output voltage change
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Consider an inverting amplifier with a nominal gain of 1000, an op amp with an input offset voltage of 3 mV and an output saturation voltage of plus or minus 10 V. (a) Find the peak value (approximately) of the sine wave input signal that will not cause the output voltage to be cut off?
(b) If the effect of Vos is zero at room temperature (25°C): (I) if the circuit operates at a predetermined temperature; (ii) the temperature coefficient of Vas is known to be 10μV/°C, and the circuit is operable In the range of 0°C to 75°C. Please find the maximum signal we can input in the two cases respectively.
Select true or false for 1 and 21 Op amp component is temperature limited due to maximum output current2 The input offset voltage affects the value of the opamp output and is caused by internal non-idealities in the transistors and resistors.
3 What is the use of an op amp in voltage follower?
Select one:a. It is the ideal bridge to couple any stages without affecting the voltage.b. It is ideal for maximum power transferc. Allows a small signal to be amplified with high gaind. voltage attenuation
4. It allows to eliminate the problem of variability in the gain parameter of the circuit:Select one:a. The load RLb. High input impedancec. feedback loopd. decoupling capacitors
5 Complete: The output current is limited due to the _____ that the opamp can handle, while the ______ is limiting due to the maximum bias level supported by the transistor.
Show the connection of a three-stage amplifier with gains of +10, -18, and -27.Use a 270-kΩ feedback resistor for all three 741 op-amp circuits. What outputvoltage will result for an input of 150 mV?
Chapter 2 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 2.1 - Prob. 2.1ECh. 2.1 - Prob. 2.2ECh. 2.1 - Prob. 2.3ECh. 2.2 - Prob. D2.4ECh. 2.2 - Prob. 2.5ECh. 2.2 - Prob. 2.6ECh. 2.2 - Prob. D2.7ECh. 2.2 - Prob. D2.8ECh. 2.3 - Prob. 2.9ECh. 2.3 - Prob. 2.10E
Ch. 2.3 - Prob. D2.11ECh. 2.3 - Prob. 2.12ECh. 2.3 - Prob. 2.13ECh. 2.3 - Prob. 2.14ECh. 2.4 - Prob. 2.15ECh. 2.4 - Prob. D2.16ECh. 2.4 - Prob. 2.17ECh. 2.5 - Prob. 2.18ECh. 2.5 - Prob. D2.19ECh. 2.5 - Prob. D2.20ECh. 2.6 - Prob. 2.21ECh. 2.6 - Prob. 2.22ECh. 2.6 - Prob. 2.23ECh. 2.6 - Prob. 2.24ECh. 2.6 - Prob. 2.25ECh. 2.7 - Prob. 2.26ECh. 2.7 - Prob. 2.27ECh. 2.7 - Prob. 2.28ECh. 2.8 - Prob. 2.29ECh. 2.8 - Prob. 2.30ECh. 2 - Prob. 2.1PCh. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Prob. 2.4PCh. 2 - Prob. 2.5PCh. 2 - Prob. 2.6PCh. 2 - Prob. 2.7PCh. 2 - Prob. 2.8PCh. 2 - Prob. 2.9PCh. 2 - Prob. 2.10PCh. 2 - Prob. 2.11PCh. 2 - Prob. D2.12PCh. 2 - Prob. D2.13PCh. 2 - Prob. D2.14PCh. 2 - Prob. 2.15PCh. 2 - Prob. 2.16PCh. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Prob. 2.19PCh. 2 - Prob. D2.20PCh. 2 - Prob. 2.21PCh. 2 - Prob. 2.22PCh. 2 - Prob. 2.23PCh. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - Prob. D2.26PCh. 2 - Prob. 2.27PCh. 2 - Prob. 2.28PCh. 2 - Prob. D2.29PCh. 2 - Prob. 2.30PCh. 2 - Prob. 2.31PCh. 2 - Prob. 2.32PCh. 2 - Prob. D2.33PCh. 2 - Prob. D2.34PCh. 2 - Prob. D2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. D2.37PCh. 2 - Prob. D2.38PCh. 2 - Prob. D2.39PCh. 2 - Prob. D2.40PCh. 2 - Prob. D2.41PCh. 2 - Prob. D2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. D2.44PCh. 2 - Prob. D2.45PCh. 2 - Prob. D2.46PCh. 2 - Prob. D2.47PCh. 2 - Prob. D2.48PCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. D2.51PCh. 2 - Prob. D2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. D2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. D2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. D2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. D2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. D2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. D2.76PCh. 2 - Prob. 2.77PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. D2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. D2.82PCh. 2 - Prob. D2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. D2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. D2.92PCh. 2 - Prob. D2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. D2.99PCh. 2 - Prob. D2.100PCh. 2 - Prob. 2.101PCh. 2 - Prob. 2.102PCh. 2 - Prob. 2.103PCh. 2 - Prob. 2.104PCh. 2 - Prob. 2.105PCh. 2 - Prob. 2.106PCh. 2 - Prob. 2.107PCh. 2 - Prob. 2.108PCh. 2 - Prob. 2.109PCh. 2 - Prob. 2.110PCh. 2 - Prob. 2.111PCh. 2 - Prob. 2.112PCh. 2 - Prob. 2.113PCh. 2 - Prob. 2.114PCh. 2 - Prob. 2.115PCh. 2 - Prob. D2.116PCh. 2 - Prob. D2.117PCh. 2 - Prob. D2.118PCh. 2 - Prob. 2.119PCh. 2 - Prob. 2.120PCh. 2 - Prob. 2.121PCh. 2 - Prob. 2.122PCh. 2 - Prob. 2.123PCh. 2 - Prob. 2.124PCh. 2 - Prob. 2.125PCh. 2 - Prob. 2.126PCh. 2 - Prob. D2.127P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An inverting amplifier is built with R2 =47kΩ and R1 = 2.4kΩ using an op amp with an open-loop gain of 100 dB, an input resistance of 300 kΩ, and an output resistance of 200 Ω. What are the closed-loop gain, input resistance, and output resistance for this amplifier? (b) Repeat if the open-loop gain is changed to 94 dB.arrow_forwardA noninverting amplifier is built with R2 = 75 kΩ and R1 = 5.6kΩ using an op amp with an open -loop gain of 100dB, an input resistance of 500kΩ, and an output resistance of 300 Ω. What are the closed-loop gain, input resistance, and output resistance for this amplifier? (b) Repeat if the open-loop gain is changed to 94 dB.arrow_forwardShow the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? fot third stage)arrow_forward
- Q2/B)- Show the connection of three combination op-amp stages ( Parallel and series connection) using an LM348 IC to provide outputs that are 110, 400, and 2601 times larger than the input. Use a feedback resistor of Rf = 500 k? in all stages, while can use only (R= 50 k? for first stage), (R= 25 k? for second stage), and (R= 10 k? for third stagearrow_forwardAn inverting amplifier with a voltage gain of 5 is built with an operational amplifier with finite slew rate. When the frequency of an input sinusoid signal with 1V amplitude is larger than 20 kHz, the distortion of the output voltage occurs. According to this experimental result, calculate the slew rate of the operational amplifier.arrow_forwardConsidering the amplifier gain 13 and the number 2 as N, design a Wien Bridge oscillator circuit with an oscillating frequency ((1 + N) × 1000) Hz. Draw the circuit. Show the process steps. Show the values of the circuit elements in your drawing. I would be very happy if you could be quick :)arrow_forward
- 1. For n-stage analog amplifier circuit, if the voltage gain of each stage is Adi and the op amp common-mode rejection ratio is CMRRi (I =1~N): a) derive the mathematical expressions for the CMRR for the whole circuit b) analyze which stage’s CMRR has the most influence on the overall CMRR.arrow_forwardA differential amplifier has a differential gain of 500 and negligible common-mode gain. The input terminals are tied to ground through 1-kΩ resistors having tolerances of ±5 percent. What are the extreme values of the output voltage caused by a bias current of 100 nA? What is the output voltage if the resistors are exactly equal?arrow_forward1. Find the Thévenin equivalent circuit with respect to the output terminals a, b for the inverting amplifier shown. The dc signal source has a value of 880 mV. The op amp has an input resistance of 500 kΩ, an output resistance of 2 kΩ, and an openloop gain of 100,000. 2. What is the output resistance of the inverting amplifier? 3. What is the resistance (in ohms) seen by the signal source vs when the load at the terminals a, b is 330 Ω?arrow_forward
- For an op-amp working in differential mode, when inputs of VI= −200 mV, andVN = +200 mV are applied, the amplifier output is recorded as Vo = 1.0012 V.When the op-amp is used in a common mode amplifier with inputs VI=VN =5V,the output is V0= 0.2217 V. Determine the common mode rejection ratio(CMRR), expressed in dB.arrow_forwardAn amplifier is formed by cascading three identical operational-amplifier stages, as shown . (a) Replace each op amp circuit with itstwo-port representation. (b) Use the circuit model from part (a) to find the overall two-port representation (Av, Rin, Rout) for the complete three-stageamplifier. (c) Draw the two-port circuit corresponding to the complete three-stage amplifier.arrow_forwardFor Va = 250 mV, if the circuit given below is analyzed using the detailed model of an op amp (as opposed to the ideal op-amp model), calculate the value of open-loop gain A required to achieve a closed-loop gain within 2 percent of its ideal value. Assume zero output resistance and infinite input resistance for the 250-Ω resistor.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
Current feedback amplifiers - Overview and compensation techniques; Author: Texas Instruments;https://www.youtube.com/watch?v=2WZotqHiaq8;License: Standard Youtube License