Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
7th Edition
ISBN: 9780199339136
Author: Adel S. Sedra, Kenneth C. Smith
Publisher: Oxford University Press
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem D2.92P
To determine
The transfer function of the high- pass active filter.
To prove: The dc gain is given as
To design: Active high-pass active filter circuit for a given high frequency input resistance, high frequencygain and 3-dB frequency.
Also, the frequency at which the magnitude of the transfer function reduces to unity.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
40. Given that fc(ol) = 100 Hz, Aol = 50 dB, and fc(cl) = 3 kHz, determine the closed-loop gain in decibels
What is the unity-gain bandwidth in Problem 40?
42 to 44. For each amplifier in the Figures shown determine the closed-loop gain, Acl and bandwidth, BWcl. The op-amps in each circuit exhibit an open-loop gain, Aol of 100 dB and a unity-gain bandwidth, fT of 1 MHz
For the circuit in the figure, extract the following as the formula according to r model and π model.
a) IB, IC and IE currents
b) The voltages at the X, B, C, E points and the voltage VCE
c) Ri input resistance and output resistance Ro
d) Av Voltage gains
e) Low cutoff frequencies
f) Formulate the high cutoff frequencies.
(a) What are the worst-case values (minimum or maximum, as appropriate) of the following parameters of the AD745 op amp: open-loop gain, CMRR, PSRR, VOS, IB1, IB2, IOS, RID, slew rate, gain-bandwidth product, and power supply voltages? (b) Repeat for an LT1028 op amp.
Chapter 2 Solutions
Microelectronic Circuits (The Oxford Series in Electrical and Computer Engineering) 7th edition
Ch. 2.1 - Prob. 2.1ECh. 2.1 - Prob. 2.2ECh. 2.1 - Prob. 2.3ECh. 2.2 - Prob. D2.4ECh. 2.2 - Prob. 2.5ECh. 2.2 - Prob. 2.6ECh. 2.2 - Prob. D2.7ECh. 2.2 - Prob. D2.8ECh. 2.3 - Prob. 2.9ECh. 2.3 - Prob. 2.10E
Ch. 2.3 - Prob. D2.11ECh. 2.3 - Prob. 2.12ECh. 2.3 - Prob. 2.13ECh. 2.3 - Prob. 2.14ECh. 2.4 - Prob. 2.15ECh. 2.4 - Prob. D2.16ECh. 2.4 - Prob. 2.17ECh. 2.5 - Prob. 2.18ECh. 2.5 - Prob. D2.19ECh. 2.5 - Prob. D2.20ECh. 2.6 - Prob. 2.21ECh. 2.6 - Prob. 2.22ECh. 2.6 - Prob. 2.23ECh. 2.6 - Prob. 2.24ECh. 2.6 - Prob. 2.25ECh. 2.7 - Prob. 2.26ECh. 2.7 - Prob. 2.27ECh. 2.7 - Prob. 2.28ECh. 2.8 - Prob. 2.29ECh. 2.8 - Prob. 2.30ECh. 2 - Prob. 2.1PCh. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Prob. 2.4PCh. 2 - Prob. 2.5PCh. 2 - Prob. 2.6PCh. 2 - Prob. 2.7PCh. 2 - Prob. 2.8PCh. 2 - Prob. 2.9PCh. 2 - Prob. 2.10PCh. 2 - Prob. 2.11PCh. 2 - Prob. D2.12PCh. 2 - Prob. D2.13PCh. 2 - Prob. D2.14PCh. 2 - Prob. 2.15PCh. 2 - Prob. 2.16PCh. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Prob. 2.19PCh. 2 - Prob. D2.20PCh. 2 - Prob. 2.21PCh. 2 - Prob. 2.22PCh. 2 - Prob. 2.23PCh. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - Prob. D2.26PCh. 2 - Prob. 2.27PCh. 2 - Prob. 2.28PCh. 2 - Prob. D2.29PCh. 2 - Prob. 2.30PCh. 2 - Prob. 2.31PCh. 2 - Prob. 2.32PCh. 2 - Prob. D2.33PCh. 2 - Prob. D2.34PCh. 2 - Prob. D2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. D2.37PCh. 2 - Prob. D2.38PCh. 2 - Prob. D2.39PCh. 2 - Prob. D2.40PCh. 2 - Prob. D2.41PCh. 2 - Prob. D2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. D2.44PCh. 2 - Prob. D2.45PCh. 2 - Prob. D2.46PCh. 2 - Prob. D2.47PCh. 2 - Prob. D2.48PCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. D2.51PCh. 2 - Prob. D2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. D2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. D2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. D2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. D2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. D2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. D2.76PCh. 2 - Prob. 2.77PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. D2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. D2.82PCh. 2 - Prob. D2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. D2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. D2.92PCh. 2 - Prob. D2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. D2.99PCh. 2 - Prob. D2.100PCh. 2 - Prob. 2.101PCh. 2 - Prob. 2.102PCh. 2 - Prob. 2.103PCh. 2 - Prob. 2.104PCh. 2 - Prob. 2.105PCh. 2 - Prob. 2.106PCh. 2 - Prob. 2.107PCh. 2 - Prob. 2.108PCh. 2 - Prob. 2.109PCh. 2 - Prob. 2.110PCh. 2 - Prob. 2.111PCh. 2 - Prob. 2.112PCh. 2 - Prob. 2.113PCh. 2 - Prob. 2.114PCh. 2 - Prob. 2.115PCh. 2 - Prob. D2.116PCh. 2 - Prob. D2.117PCh. 2 - Prob. D2.118PCh. 2 - Prob. 2.119PCh. 2 - Prob. 2.120PCh. 2 - Prob. 2.121PCh. 2 - Prob. 2.122PCh. 2 - Prob. 2.123PCh. 2 - Prob. 2.124PCh. 2 - Prob. 2.125PCh. 2 - Prob. 2.126PCh. 2 - Prob. D2.127P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A single-pole op amp has an open-loop gain of 100 dB and a unity-gain frequency of 2 MHz. Find an expression for the transfer function of the low-pass filter shown if R1 = 5.1kΩ, R2 = 100 kΩ and C = 750 pF. Make a Bode plot comparing the ideal and the actual transfer functions.arrow_forwardFind the transfer function G(s) = Vo(s)/Vi(s), for each operational amplifier circuit shown in Figure P2.6. [Section: 2.4]arrow_forwardDesign an inverting amplifier to provide a closed-loop voltage gain of Ay = -22 V/V. The maximum input voltage signal is 30 mV with a source resistance in the range of 1 kls R, < 3 kN. The variable source resistance should introduce a difference in the gain no more than a 2% of the gain factor. What is the range in output voltage?arrow_forward
- bls 3 Why the amplifier called a unity - gain while it provides 180 degree phase ? inversionarrow_forwardFind the unity-gain bandwidth of an op-amp that has a critical frequency of 10Hz and voltage differential gain AVD=100V/mV. Choices: a) 100kHz, b) 1MHz, c) 10MHz, and d) 10kHz A LM124 quad op-amp has a three-stage amplifier with gains of +15(non-inverting), -22(inverting), and -30(inverting). Use a 420-kohms feedback resistor for all stages. Determine the output voltage results for an input of V1=100uV.arrow_forwardQ2. B.) Obtain the transfer function Eo (s) / Ei(s) of the operational-amplifiercircuit shown in Figurearrow_forward
- The no-load voltage gain of the amplifier used in the circuit in the picture is K = 2000, input resistance R1 = 50K and output resistance Ro = 500ohm.a) Calculate the voltage gain of the circuit Vo / Vg.b) Calculate the value of the capacitors C1 and C2, considering that the lower cut-off frequency of the circuit is 20Hz and the asymptote slope is desired to be 40db / decade.c) Calculate the upper cut-off frequency of the circuit.arrow_forward(a) There are three voltage inputs of V1 = 1V, V2 = 3V and V3 = 4V, and three resistors with the value of 4kΩ, 2kΩ and 1kΩ. Design a single ideal operational amplifier circuit to combine these inputs to produce a single output voltage of Vout = -10.5v with a feedback resistor of Rf = 2kΩ. Provide the sketch and calculation for your designed circuit. (b) Figure 2 below shows a cascaded operational amplifier circuit. Determined the value of the output voltage Vout. (c) Figure 3 shows a bipolar junction transistor circuit in common-emitter configuration. Given that VBE = 0.7 v and ß = 110. Determine the current IB, IC, IE and the voltage VCE.arrow_forward(a) There are three voltage inputs of V1 = 1V, V2 = 3V and V3 = 4V, and three resistors with the value of 4kΩ, 2kΩ and 1kΩ. Design a single ideal operational amplifier circuit to combine these inputs to produce a single output voltage of Vout = -10.5v with a feedback resistor of Rf = 2kΩ. Provide the sketch and calculation for your designed circuit. (b) Figure 2 below shows a cascaded operational amplifier circuit. Determined the value of the output voltage Vout. (c) Figure 3 shows a bipolar junction transistor circuit in common-emitter configuration. Given that VBE = 0.7 v and ß = 110. Determine the current IB, IC, IE and the voltage VCE. [9 Marks]arrow_forward
- An opamp is having a differential gain Ad =4500 and a common mode gain Ac = 25. What will be value of Common Mode Rejection Ratio (CMRR)? Express your answer in decibels (dB).arrow_forwardConsider the circuit shown in FigureP13.24 . a. Find an expression for the output voltage in terms of the source current and resistance values. b. What value is the output impedance of this circuit? c. What value is the input impedance of this circuit? d.This circuit can be classified as an ideal amplifier. What is the amplifier type? (See Section11.6 for a discussion of various ideal-amplifier types.) Repeat ProblemP13.24 for the circuit shown in FigureP13.25 .arrow_forwardConsider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSON
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Programmable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill Education
Electric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSON
Engineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,