Fluid Mechanics: Fundamentals and Applications
4th Edition
ISBN: 9781259696534
Author: Yunus A. Cengel Dr., John M. Cimbala
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 14, Problem 109P
To determine
The efficiency of the model turbine.
The type of the prototype turbine being tested.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A 1:10 model of a Francis turbine developed 0.5 kW under a head of 2.5 m at 480 rpm. The physical data are r1=1.5m, r2 = 0.4m, α1=15°, β2=135°. Find the speed of the prototype at a head of 20m.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
The dimensions of a Francis radial-flow hydroturbine are r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m, where location 2 is the inlet and location 1 is the outlet. At the turbine inlet and outflow, the runner blade angles are β2 = 71.4° and β1 = 15.3°, respectively. The runner rotates at a rate of ń = 160 rpm. At design conditions, the volume flow rate is 80.0 m3 /s
Chapter 14 Solutions
Fluid Mechanics: Fundamentals and Applications
Ch. 14 - What is the more common term for an...Ch. 14 - What the primary differences between fans,...Ch. 14 - List at least two common examples of fans, of...Ch. 14 - Discuss the primary difference between a porn...Ch. 14 - Explain why there is an “extra” term in the...Ch. 14 - For a turbine, discuss the difference between...Ch. 14 - Prob. 7CPCh. 14 - Prob. 8PCh. 14 - Prob. 9PCh. 14 - Prob. 10CP
Ch. 14 - There are three main categories of dynamic pumps....Ch. 14 - For each statement about cow cetrifugal the...Ch. 14 - Prob. 13CPCh. 14 - Consider flow through a water pump. For each...Ch. 14 - Write the equation that defines actual (available)...Ch. 14 - Consider a typical centrifugal liquid pump. For...Ch. 14 - Prob. 17CPCh. 14 - Consider steady, incompressible flow through two...Ch. 14 - Prob. 19CPCh. 14 - Prob. 20PCh. 14 - Suppose the pump of Fig. P1 4-19C is situated...Ch. 14 - Prob. 22PCh. 14 - Prob. 23EPCh. 14 - Consider the flow system sketched in Fig. PI 4-24....Ch. 14 - Prob. 25PCh. 14 - Repeat Prob. 14-25, but with a rough pipe-pipe...Ch. 14 - Consider the piping system of Fig. P14—24. with...Ch. 14 - The performance data for a centrifugal water pump...Ch. 14 - For the centrifugal water pump of Prob. 14-29,...Ch. 14 - Suppose the pump of Probs. 14-29 and 14-30 is used...Ch. 14 - Suppose you are looking into purchasing a water...Ch. 14 - The performance data of a water pump follow the...Ch. 14 - For the application at hand, the flow rate of...Ch. 14 - A water pump is used to pump water from one large...Ch. 14 - For the pump and piping system of Prob. 14-35E,...Ch. 14 - A water pump is used to pump water from one large...Ch. 14 - Suppose that the free surface of the inlet...Ch. 14 - Calculate the volume flow rate between the...Ch. 14 - Comparing the results of Probs. 14-39 and 14-43,...Ch. 14 - Prob. 45PCh. 14 - The performance data for a centrifugal water pump...Ch. 14 - Transform each column of the pump performance data...Ch. 14 - 14-51 A local ventilation system (a hood and duct...Ch. 14 - Prob. 52PCh. 14 - Repeat Prob. 14-51, ignoring all minor losses. How...Ch. 14 - Suppose the one- way of Fig. P14-51 malfunctions...Ch. 14 - A local ventilation system (a hood and duct...Ch. 14 - For the duct system and fan of Prob. 14-55E,...Ch. 14 - Repeat Prob. 14-55E, ignoring all minor losses....Ch. 14 - A self-priming centrifugal pump is used to pump...Ch. 14 - Repeat Prob. 14-60. but at a water temperature of...Ch. 14 - Repeat Prob. 14-60, but with the pipe diameter...Ch. 14 - Prob. 63EPCh. 14 - Prob. 64EPCh. 14 - Prob. 66PCh. 14 - Prob. 67PCh. 14 - Prob. 68PCh. 14 - Prob. 69PCh. 14 - Two water pumps are arranged in Series. The...Ch. 14 - The same two water pumps of Prob. 14-70 are...Ch. 14 - Prob. 72CPCh. 14 - Name and briefly describe the differences between...Ch. 14 - Discuss the meaning of reverse swirl in reaction...Ch. 14 - Prob. 75CPCh. 14 - Prob. 76CPCh. 14 - Prob. 77PCh. 14 - Prob. 78PCh. 14 - Prob. 79PCh. 14 - Prob. 80PCh. 14 - Wind ( =1.204kg/m3 ) blows through a HAWT wind...Ch. 14 - Prob. 82PCh. 14 - Prob. 84CPCh. 14 - A Francis radial-flow hydroturbine has the...Ch. 14 - Prob. 87PCh. 14 - Prob. 88PCh. 14 - Prob. 89PCh. 14 - Prob. 90CPCh. 14 - Prob. 91CPCh. 14 - Discuss which dimensionless pump performance...Ch. 14 - Prob. 93CPCh. 14 - Prob. 94PCh. 14 - Prob. 95PCh. 14 - Prob. 96PCh. 14 - Prob. 97PCh. 14 - Prob. 98PCh. 14 - Prob. 99PCh. 14 - Prob. 100EPCh. 14 - Prob. 101PCh. 14 - Calculate the pump specific speed of the pump of...Ch. 14 - Prob. 103PCh. 14 - Prob. 104PCh. 14 - Prob. 105PCh. 14 - Prob. 106PCh. 14 - Prob. 107EPCh. 14 - Prob. 108PCh. 14 - Prob. 109PCh. 14 - Prob. 110PCh. 14 - Prove that the model turbine (Prob. 14-109) and...Ch. 14 - Prob. 112PCh. 14 - Prob. 113PCh. 14 - Prob. 114PCh. 14 - Prob. 115CPCh. 14 - Prob. 116CPCh. 14 - Prob. 117CPCh. 14 - Prob. 118PCh. 14 - For two dynamically similar pumps, manipulate the...Ch. 14 - Prob. 120PCh. 14 - Prob. 121PCh. 14 - Prob. 122PCh. 14 - Calculate and compare the turbine specific speed...Ch. 14 - Prob. 124PCh. 14 - Prob. 125PCh. 14 - Prob. 126PCh. 14 - Prob. 127PCh. 14 - Prob. 128PCh. 14 - Prob. 129PCh. 14 - Prob. 130PCh. 14 - Prob. 131PCh. 14 - Prob. 132PCh. 14 - Prob. 133PCh. 14 - Prob. 134PCh. 14 - Prob. 135PCh. 14 - A two-lobe rotary positive-displacement pump moves...Ch. 14 - Prob. 137PCh. 14 - Prob. 138PCh. 14 - Prob. 139PCh. 14 - Prob. 140PCh. 14 - Which choice is correct for the comparison of the...Ch. 14 - Prob. 142PCh. 14 - In a hydroelectric power plant, water flows...Ch. 14 - Prob. 144PCh. 14 - Prob. 145PCh. 14 - Prob. 146PCh. 14 - Prob. 147PCh. 14 - Prob. 148PCh. 14 - Prob. 149PCh. 14 - Prob. 150PCh. 14 - Prob. 151P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. After resolving the turbine speed, what horsepower would be developed under a head of 11 meters?arrow_forwardA Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.arrow_forwardLook up the word affinity in a dictionary. Why do you suppose some engineers refer to the turbomachinery scaling laws as affinity laws?arrow_forward
- The dimensions of a Francis radial-flow hydroturbine are r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m, where location 2 is the inlet and location 1 is the outlet. At the turbine inlet and outflow, the runner blade angles are β2 = 71.4° and β1 = 15.3°, respectively. The runner rotates at a rate of ń = 160 rpm. At design conditions, the volume flow rate is 80.0 m3 /s. (a) State the necessary assumptions and calculate the angle α2 at which the wicket gates should turn the flow (Figure Q1), with α2 measured from the radial direction at the runner inlet. (b) Calculate the swirl angle α1 (Figure Q1), where α1 is the angle measured from the radial direction at the runner output. (c) Calculate the needed net head and power output. (d) Discuss the actual power output and head required for actual case of the turbine (irreversibility not neglected). (Properties For water at 20oC, ρ = 998.0 kg/m3)arrow_forward2. A fan discharges 265 cu.m/min of air through a duct of 92 cm in diameter against a static pressure of 0.022 m of water. The fluid density is 995 kg/cu.m., the air temperature is 29°C and the barometric pressure reading is 730 mm Hg. If the power input to the fan is measured 3.5 hp, what are the total and static fan efficiencies?arrow_forwardFor a high-fl ow site with a head of 45 ft, it is desired to designa single 7-ft-diameter turbine that develops 4000 bhp at aspeed of 360 r/min and 88-percent effi ciency. It is decidedfi rst to test a geometrically similar model of diameter 1 ft,running at 1180 r/min. (a) What likely type of turbine is inthe prototype? What are the appropriate (b) head and(c) fl ow rate for the model test? (d ) Estimate the powerexpected to be delivered by the model turbine.arrow_forward
- A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps? Assuming the head is equally divided between the two pumps, what is the efficiency of either pumps (in %)? Take the specific weight of water to be 62.4 lbf/ft3.arrow_forwardPAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answerarrow_forwardA certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps?arrow_forward
- A turbine rotates at 150 rpm and discharges 0.8 m3/s. The radial velocity at inlet Cr1 = 2 m/s and equals 6 m/s at exit. The physical data are: r1 = 0.5 m, r2 = 0.2 m, α1 = 15°, β2 = 135°, Z1 = Z2, the pressure head at exit is 6 m. Assuming a loss of head of 2 m, calculate the following: The water horsepower delivered by the turbine, (no draft tube are used) neglect circulatory flow and hydraulic losses. The pressure head, in meters, at the entrance. The degree of reaction.arrow_forwardConsider the following compressor that receives air at a constant rate of three cubic feet per second. Air exits the compressor at a pressure of 95 pounds per square inch and 425 °F. Assume that there are no changes in potential or kinetic energy. With the assumption that there are constant specific heats, what is the power, in hp, consumed by the compressor? Surrounding P1=14.5 psi and T1= 68 °Farrow_forwardIt is required to construct a hydraulic turbine (inward Francis type) for a hydraulic power plant to operate under the following conditions: rotating speed N = 110 rpm, discharge Q = 11 m3/s, the radial velocity at the inlet Cr1 = 2 m/s, the radial velocity at exit Cr2 = 9.5 m/s and the physical data are: the outside diameter D1 = 4.5 m, the absolute inlet angle α1 = 15°, the absolute exit angle α2 = 90° (radial flow at exit). Assume that the potential energy is constant (Z1 = Z2), the pressure head at exit equal 6 m, the hydraulic losses are 2 m, and no draft tube. Calculate the following:The pressure head at entrance in kg/cm2It is required to construct a prototype to predict the actual machine performance, the assumed outside diameter D2 of the prototype was 0.3 m and the hydraulic circuit in the laboratory has the following specification: Available head = 5.5 m, Hydraulic efficiency = 0.8. Find the required speed, in RPM: The Head subjected on the turbine in meters.The…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license