(a)
Interpretation:
Substituted ammonium ion has to be named.
Concept Introduction:
IUPAC rules for naming ammonium ions:
There are two rules that has to be followed while naming a positive ion (ammonium ion) and they are,
- In order to name an ammonium salt from alkylamine, the ending of the name
amine is changed from amine to ammonium ion. - In order to name an
aromatic amine, the ending of the name “-e” is replaced by “-ium ion”.
(b)
Interpretation:
Substituted ammonium ion has to be named.
Concept Introduction:
IUPAC rules for naming ammonium ions:
There are two rules that has to be followed while naming a positive ion (ammonium ion) and they are,
- In order to name an ammonium salt from alkylamine, the ending of the name amine is changed from amine to ammonium ion.
- In order to name an aromatic amine, the ending of the name “-e” is replaced by “-ium ion”.
(c)
Interpretation:
Substituted anilinium ion has to be named.
Concept Introduction:
IUPAC rules for naming ammonium ions:
There are two rules that has to be followed while naming a positive ion (ammonium ion) and they are,
- In order to name an ammonium salt from alkylamine, the ending of the name amine is changed from amine to ammonium ion.
- In order to name an aromatic amine, the ending of the name “-e” is replaced by “-ium ion”.
(d)
Interpretation:
Substituted anilinium ion has to be named.
Concept Introduction:
IUPAC rules for naming ammonium ions:
There are two rules that has to be followed while naming a positive ion (ammonium ion) and they are,
- In order to name an ammonium salt from alkylamine, the ending of the name amine is changed from amine to ammonium ion.
- In order to name an aromatic amine, the ending of the name “-e” is replaced by “-ium ion”.
Want to see the full answer?
Check out a sample textbook solutionChapter 17 Solutions
EBK GENERAL, ORGANIC, AND BIOLOGICAL CH
- Complete the table below. Assume that the only reaction is dissolution. Ignore the effects of acid/base hydrolysis. Show complete solutions. Show both the rounded and non-rounded answers. For the rounded answer, express in exactly 5 significant figures. Salt Ksp Common ion [cation] [anion] AgX 2.24 х 103 М х 5.27 х 109м Hg2X2 1.33 x 102 M Hg2* 1.65 x 107 Marrow_forwardExplain the mechanism of denaturation for the following agent: 1. Hydrochloric acid 2. Lead (II) acetate solution 3. Picric acid 4. Nitric acid 5. Ethanolarrow_forwardA prescription came in for 34% salicylic acid. The pharmacy has 95% salicylic and 10%salicylic acid available. Write a recipe for 500mg of 34% salicylic acid.arrow_forward
- Trans-oleic acid (18:1,D9) has a melting temperature of (44.5C) and cis-oleic acid (18:1,D9) has a melting point of (13.4C). Briefly explain the difference in melting points between the two. tw.arrow_forwardCalculate the concentration of Y4-ion in 0.0100 M EDTA solution at pH 6. α4 = 2.2 x 10-5 for pH 6.arrow_forwardWrite out the acid dissociation reaction for hydrochloric acid. Calculate the pH of a solution prepared by diluting 3 ml of 0.5 M HCl to a final volume of 100 ml with H2Oarrow_forward
- What is the pH of the solution given the following information? Methyl orange = yellow Methyl red = yellow Bromothymol blue = green Note: use the provided reference table for color indicators below as a guide pH 5 pH 8 pH 7 pH 6arrow_forwardDiscuss the suitability of bromocresol green and thymol blue (2nd change only) for use as indicators in an acetic acid - sodium hydroxide titration. Paragraph в I A + v ...arrow_forwardA 1.000-g sample containing bromide was dissolved in sufficient water to give 100.0 mL. A 50.00 mL aliquot was measured and after acidification, silver nitrate was introduced to precipitate AgBr, which was filtered, washed, and then dissolved in an ammoniacal solution of potassium tetracyanonickelate(II): Ni(CN)42- + 2AgBr(s) → 2Ag(CN)2- + Ni2+ + 2Br- The liberated nickel ion required 11.70 mL of 0.002146 M EDTA. The other 50.00 mL remaining solution was also analyzed for its Br- content by potentiometry using a metallic electrode of the second kind. e) Write the cell notation of the potentiometric set-up with SCE as the reference electrode. f) Write the Nernst equation that describes the indicator electrode set-up.arrow_forward