EBK NUMERICAL METHODS FOR ENGINEERS
7th Edition
ISBN: 9780100254145
Author: Chapra
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 20, Problem 10P
Concentration data were taken at 15 time points for the polymerization reaction
We assume the reaction occurs via a complex mechanism consisting of many steps. Several models have been hypothesized and the sum of the squares of the residuals had been calculated for the fits of the models of these data. The results are shown below. Which model best describe these data (statistically)? Explain your choice.
| Model A | Model B | Model C | |
|
|
135 | 105 | 100 |
| Number of model parameters fit |
2 | 3 | 5 |
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
I1
Give an example how it is applied in molecular dynamics simulation and Monte carlo simulation?
Typical distributions of particles in a volume (e.g. crystal structure for a solid, or distribution of masses and velocities in a “typical” galaxy) - Distributions of particle velocities/energies (e.g. Boltzmann distribution at a fixed temperature)
- E.g. for a liquid it is common to start with a solid crystal structure and let the structure “melt” (by setting appropriate velocities corresponding to the liquid phase temperature!)
- E.g. to setup a collision of two galaxies, you could try to generate a stable distribution of masses and velocities for a single galaxy first by performing a separate simulation
-E.g. A simple model of a phase transition between a low temperature ordered phase (ferromagnet) and high temperature disordered phase (paramagnet)
whats the difference in phase space in Molecular dynamics and Monte Carlo simulation?
A 30 wt% Ni-70 wt% Cu alloy (Animated Figure 9.3a) is slowly cooled from 1400°C (2550°F) to 1150°C (2100°F).
(a) At what temperature does the first solid phase form?
i
! °C
(b) What is the composition of this solid phase?
i
%wt Ni
(c) At what temperature does the last of the liquid solidify?
i
°℃
(d) What is the composition of this last remaining liquid phase?
i
%wt Ni
The materials laboratory that you direct received the following data on the tensile strength in MPa of 15 samples of Aluminum Nitride. The data obtained for each sample are: Sample Endurance (Mpa)
SAMPLE
(STRENGTH) MPa
1
190
2
233
3
268
4
160
5
257
6
300
7
310
8
262
9
185
10
205
11
275
12
245
13
220
14
290
15
228
You are asked to calculate the Weibull modulus, m, considering that the probability of failure is n/16, where n is the number of specimens that failed at a given stress. You can use Excel to speed up the calculations.
Chapter 20 Solutions
EBK NUMERICAL METHODS FOR ENGINEERS
Ch. 20 - 20.1 Perform the same computation as in Sec. 20.1,...Ch. 20 - You perform experiments and determine the...Ch. 20 - 20.3 It is known that the tensile strength of a...Ch. 20 - Prob. 4PCh. 20 - 20.5 The specific volume of a superheated steam is...Ch. 20 - Prob. 6PCh. 20 - In Alzheimers disease, the number of neurons in...Ch. 20 - 20.8 The following data were taken from a stirred...Ch. 20 - Prob. 9PCh. 20 - Concentration data were taken at 15 time points...
Ch. 20 - Prob. 11PCh. 20 - The molecular weight of a polymer can be...Ch. 20 - 20.13 On average, the surface area A of human...Ch. 20 - 20.14 Determine an equation to predict metabolism...Ch. 20 - 20.15 Human blood behaves as a Newtonian fluid...Ch. 20 - 20.16 Soft tissue follows an exponential...Ch. 20 - 20.17 The thickness of the retina changes during...Ch. 20 - 20.18 The data tabulated below were generated from...Ch. 20 - The shear stresses, in kilopascals (kPa), of nine...Ch. 20 - 20.20 A transportation engineering study was...Ch. 20 - The saturation concentration of dissolved oxygen...Ch. 20 - For the data in Table P20.21, use polynomial...Ch. 20 - 20.23 Use multiple linear regression to derive a...Ch. 20 - 20.24 As compared to the models from Probs. 20.22...Ch. 20 - 20.25 In water-resources engineering, the sizing...Ch. 20 - 20.26 The concentration of total phosphorus and...Ch. 20 - 20.27 The vertical stress under the corner of a...Ch. 20 - Three disease-carrying organisms decay...Ch. 20 - 20.29 The mast of a sailboat has a cross-sectional...Ch. 20 - 20.30 Enzymatic reactions are used extensively to...Ch. 20 - 20.31 Environmental engineers dealing with the...Ch. 20 - An environmental engineer has reported the data...Ch. 20 - The following model is frequently used in...Ch. 20 - 20.34 As a member of Engineers Without Borders,...Ch. 20 - 20.35 Perform the same computations as in Sec....Ch. 20 - 20.36 You measure the voltage drop V across a...Ch. 20 - Duplicate the computation for Prob. 20.36, but use...Ch. 20 - The current in a wire is measured with great...Ch. 20 - 20.39 The following data was taken from an...Ch. 20 - It is known that the voltage drop across an...Ch. 20 - Ohms law states that the voltage drop V across an...Ch. 20 - 20.42 Repeat Prob. 20.41 but determine the...Ch. 20 - 20.43 An experiment is performed to determine the...Ch. 20 - Bessel functions often arise in advanced...Ch. 20 - 20.45 The population of a small community on the...Ch. 20 - Based on Table 20.4, use linear and quadratic...Ch. 20 - 20.47 Reproduce Sec. 20.4, but develop an equation...Ch. 20 - 20.48 Dynamic viscosity of water is related to...Ch. 20 - 20.49 Hooke’s law, which holds when a spring is...Ch. 20 - 20.50 Repeat Prob. 20.49 but fit a power curve to...Ch. 20 - The distance required to stop an automobile...Ch. 20 - An experiment is performed to define the...Ch. 20 - The acceleration due to gravity at an altitude y...Ch. 20 - The creep rate is the time rate at which strain...Ch. 20 - 20.55 It is a common practice when examining a...Ch. 20 - The relationship between stress and the shear...Ch. 20 - The velocity u of air flowing past a flat surface...Ch. 20 - 20.58 Andrade’s equation has been proposed as a...Ch. 20 - Develop equations to fit the ideal specific heats...Ch. 20 - 20.60 Temperatures are measured at various points...Ch. 20 - 20.61 The data below were obtained from a creep...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Analytic Functions. Find fz=ux,y+ivx,y with u or v as given. Check by the Cauchy Reimann equations for analyti...
Advanced Engineering Mathematics
|4.2| = ?
Basic Technical Mathematics
(a) Show that (x) = x2 is an explicit solution to xdydx = 2y on the interval (, ). (b) Show that (x) = ex x is...
Fundamentals of Differential Equations (9th Edition)
the proportion of red cars in the sample and display the sampling distribution of the sample proportion on dot ...
PRACTICE OF STATISTICS F/AP EXAM
Provide an example of a qualitative variable and an example of a quantitative variable.
Elementary Statistics (Text Only)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- O You are running an industrial research study together with your project team to improve energy efficiency in a combustion process. The purpose of the research is to identify the optimum air-fuel ratio for the combustion process in a boiler under varying conditions of air supply and quality of fuel. The study would involve design of experiments, data collection and analysis, simulation of the different variables and validation of the optimum parameters. There is a lot of pressure to improve the energy efficiency as there is a forecast of fuel price rise in the forthcoming month. Based on the CRPE code of ethics, explain two critical precautions which the engineers have to consider before implementation of the data collection process for the industrial experiment. to be taken during the Describe briefly five ethical measures experimentaldata collection in order to ensure validity of results. Explain two precautions to be taken during the report writing on the research study carried out…arrow_forwardSelect two saturated and two unsaturated samples of air from the dataset of pressure and temperature given below: Pressure (mb): 10, 20, 30 Temperature (°C): 10, 20, 30 Let A and B be two air samples, where A: (T=30°C, P=25 mb) and B: (T=30°C, P=30 mb). For each sample, determine the following: a. Saturation vapor pressure b. Dew point c. Relative humidity d. If samples A and B were cooled to 15°C. What would be their relative humidity? What would be their dew point temperature?arrow_forward100 2200 20 40 60 80 1200 2000 -Liquidus 1000 Liquid 1800 Solidus F a +L 1600 B+L 800 779°C (Tg). E 8.0 71.9 91.2 1400 (CaE (Cg) (CBE 1200 600 Solvus 1000 a + B 800 400 C 600 H 200 0 400 100 20 40 60 80 (Cu) Composition (wt% Ag) (Ag) 1- define pointe E? 2- define pointe B? 3- define the line AE? 4- define the line BG? 5- define the line FG? Temperature (°C) Temperature ('F)arrow_forward
- The heat transfer conducted through material is calculated from the equation: Q = KX AXTD/L Where K: Conductivity of material A: Area of heat transfer TD: Temperature difference across material L: Thickness of material A student measures the area, thickness and temperature difference and assumes that the error in conductivity is negligible. The student also estimates the uncertainty range for each variable. In estimating the maximum possible value of Q, the student should use the following formula: A B Q max= K x A max x TD max / L max Q max= K x A max x TD max / L nom Q max= Q nominal + dQ/dLmin Q max= K x A max x TD max / L minarrow_forwardA light bulb manufacturer wants to maximize bulb lifetime. Four parameters are to be tested: Parameters a and b are the concentrations of a certain alloys in the filament. Parameters c and d are the temperature and speed, respectively, at which the filaments are extruded in the manufacturing process. A three-level experiment is be used. Levels 1, 2, and 3 correspond to low, medium, and high values of each respective parameter. Taguchi's 9-run design array (as in the learning module) is to be used. For each experimental run, thirty bulbs are tested, and the mean time to failure (MTTF) for each run is recorded as X₁, X₂, etc. These values, in order, are 1318, 1375, 1414, 1490, 1532, 1296, 1455, 1219, and 1266 hours, to four significant digits. (a) Generate a table with the above values configured as a Taguchi 9-run design array (Excel is recommended). Calculate all 12 level averages, i.e. Xal, Xa2, X3, Xb₁‚ õ2, Xd3 (b) Generate four plots, showing the dependence of X on each parameter.…arrow_forwardWhat's the correlation coefficient of the following data set? x = [-3 3 4 2 1 1 4 5] and y = [-3 2 8 -2 0 3 7 8] Type your answer...arrow_forward
- A bacteria culture is known to grow at a rate proportional to the amount present. (a) Write down and solve a DE modeling this process. (Your solution will contain two unknown constants.) (b) After one hour, 1000 strands of the bacteria are observed in the culture; and after four hours, 3000 strands. Use this information to complete the determination of the DE. c) Find the approximate number of strands of the bacteria originally in the culture. (d) How long will it take to reach 10,000 strands of the bacteria in the culture.arrow_forwardYou are developing a porous membrane for use in a dialysis system. The membrane must be able to retain both protein and glucose on the inlet side and allow other, smaller molecules to flow through. You have found that the membrane is 0.25 mm thick and contains long, rectangular pores with a width of 0.1 microns. 57% of the 50 cm^2 membrane surface area is covered with pores. A test fluid (viscosity = 1.5 cP, density = 1015 kg/m^3) is passed through the membrane. You can assume that the test fluid has a composition similar to that of blood plasma. An initial test is run at physiological conditions, and you observe that the flow rate of fluid through the membrane is 500 cm^3/min. Given this data, what must the hydrodynamic pressure drop across the membrane in your test system be in pascals?arrow_forwardHow many kilograms of nickel must be added to 5.66 kg of copper to yield a liquidus temperature of 1200°C? Use Animated Figure. kg iarrow_forward
- The empty cylinder of a soil-coring tool weighs 47.27 g, and holds a total volume of 220 cm3. The following mass data were gathered from an undisturbed, bulk sample collected with this tool: 1) Moist soil at approximately field capacity + coring cylinder = 377.21 grams 2) Oven dry soil + coring cylinder: 338.92 grams Given these data and the assumption of an average particle density of 2.65 g/cm3 for this soil, then what percentage of the total volume in this soil sample is solid particles? Your Answer: Answer unitsarrow_forwardMolecule Weight mass (lb) 1 104 2 116 140 143 5 180 6 182 7 191 220 9 225 10 380 What is the average weight of the polymer: a) Based on the number fraction of molecules in each mass range? b) Based on the weight fraction of molecules in each mass range? Sort the molecules into weight ranges using 40-lb ranges, starting from 801b. 3. 4)arrow_forwardAreas Under the Standard Normal Curve-The Values Were Generated Using the Standard Normal Distribution Function of Excel Note that the standard normal curve is symmetrical about the mean. z 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.11 0.12 1 0.95 0.96 0.97 0.98 0.99 1.01 1.02 1.03 1.04 1.05 Mean - 0 1.06 1.07 1.08 1.09 A 0.0000 0.0040 0.0080 0.0120 0.0160 0.0199 0.0239 0.0279 0.0319 0.0359 0.0398 0.0438 0.0478 A 0.3186 0.3212 0.3238 0.3264 0.3289 0.3315 0.3340 0.3365 0.3389 Z 0.3413 0.3438 0.3461 0.3485 0.3508 0.3531 0.3554 0.3577 0.3599 0.3621 0.13 0.14 0.15 0.16 0.17 0.18 0.19 0.2 0.21 0.22 0.23 0.24 0.25 1.12 1.13 1.14 1.15 1.16 1.17 A z 0.0517 0.0557 0.26 0.27 0.28 0.29 0.0596 0.0636 0.0675 0.3 0.0714 0.31 0.0753 0.32 0.0793 0.33 0.0832 0.34 0.0871 0.35 0.0910 0.0948 0.0987 1.18 1.19 1.2 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 A 0.3643 0.3665 0.3686 0.3708 0.3729 0.3749 0.3770 0.3790 0.3810 0.36 0.3830 0.3849 0.3869 0.3888 0.3907 0.3925 0.3944 0.3962 0.3980 0.3997 0.37…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Correlation Vs Regression: Difference Between them with definition & Comparison Chart; Author: Key Differences;https://www.youtube.com/watch?v=Ou2QGSJVd0U;License: Standard YouTube License, CC-BY
Correlation and Regression: Concepts with Illustrative examples; Author: LEARN & APPLY : Lean and Six Sigma;https://www.youtube.com/watch?v=xTpHD5WLuoA;License: Standard YouTube License, CC-BY