Consider a thin-walled tube of
(a) If the tube surface is maintained at a uniform temperature of
(b) What is the exit temperature of the water if it is heated by passing air at
(c) In the foregoing calculations, were the assumed values of
Want to see the full answer?
Check out a sample textbook solutionChapter 8 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Engineering Mechanics: Dynamics (14th Edition)
Applied Fluid Mechanics (7th Edition)
Heating Ventilating and Air Conditioning: Analysis and Design
Statics and Mechanics of Materials (5th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- Water at 27°C flows with a mean velocity of 1 m/s through a 1 km-long pipe of 0.25 m inside diameter. Answer the following: a. Is the flow hydrodynamically fully developed? Support your answer with calculations. b. Is the flow thermally fully developed? Support your answer with calculations. c. What is the pressure drop over the pipe length, if the pipe surface is smooth? (Ans: 0.289 Bar) d. What is the pump power requirement, if the pipe surface is smooth? (Ans: 1.42 kW)arrow_forwardA saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the % of pressure drop? (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/molarrow_forwardHelium at 25°C and 110 kPa (absolute) flows into a copper tube (1-1/4-standard, type M) that is 10 m long. Is the flow fully developed at tube end if the helium mass flow rate is 0.02 kg/s? Ethyl alcohol flows into a 6 cm ID pipe through a well-rounded entrance. After 20 cm of pipe length, measurements taken in the pipe show that the flow is fully developed. Determine the volume flow rate in the pipe, assuming laminar flow exists.arrow_forward
- 2- To solve these problems, refer to notes on Blackboard about convection inside pipes. Also, assume that the inside wall temperature of the cylinder is 100 °C Steam condensing circular tube of diameter D=50 mm and length L= 6 m maintains a uniform outer surface temperature of 100 °C Water flows through the tube at a rate m = 0.25 kg/s, and its inlet bulk temperature is To 15 °C. Determine: on the outer surface of a thin-walled a If the flow is laminar or turbulent b) The exit bulk temperature c) T (C) h (W/m2.K) d) Rate of heat transfer from steam to water e) A plot of T vs x, where x is the distance in axial direction along the pipe = 57 °C. Only State any assumptions made, and use L, guess one iteration is needed.arrow_forwardOil whose temperature is constant at 20 ° C (ρ = 886 kg / m3, μ = 0.805 kg / m / s) It flows continuously and fully developed from its length. The pressure at the entrance of this 40 m length is 720 kPa, pressure at its outlet is measured as 101 kPa. Flow is laminar. Volume flow rates, average velocities, Reynolds numbers and Darcy friction factors a-That the pipe is horizontal b-The pipe makes 20 ° counterclockwise with the horizontal c-The pipe makes 15 ° clockwise with the horizontal. Calculate for situations.arrow_forwardA 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.arrow_forward
- QUESTION 9 A liquid cooled heat sink for a smartphone is sketched in Figure Q9. It uses water of density p = 997 kg m-3 and kinematic viscosity v = 1.19 x 10-6 m²-s-1 that runs in the x₁ direction through each of the five tubes of constant diameter D₁ = 5 mm and length Lx1 = 20 mm. It is supplied by a U = 0.017 m-s-1 uniform water inflow. Use Blasius' skin friction coefficient Cf = 0.664 / Rex1 0.5 to calculate the total skin friction drag force imparted by the flow on the heat sink walls. Calculate your answer in microNewtons, to one decimal place and enter the numerical value only. 1 microNewton = 10-6 Newtons. Partial credit is awarded for a reasonable approximation to the correct numerical answer. Lx₂ X2 Lx1 X1 Ő ve Heat Flux (9) (a) Figure Q9: Schematic of a liquid cooled heat sink LX3 4arrow_forwardQ2. Water is heated while following through a 1.5cmx 3.5cm rectangular cross section tube at a velocity of 1.2 m/s. The entering temperature of the water is 40°C and the tube wall is maintained at 85 C. Determine the length of the tube required to raise the temperature of water to 70 C. If the pressure loss in the tube is registered to be 10KPa. find the required pumping power. The properties of water are: p=985.5 kg/m², C- 4.18kJ/Kg. v-0.517x10 m/s, k-0.654 W/mK and Pr-3.26. Nu =0.023Re** Prarrow_forward48. Water is flowing in a smooth pipe of diameter D. A section of this pipe hav- ing a length of L is heated. Water at the inlet to the heated section has a tempera- ture of Tŋ. Water temperature at the exit of the heated section is Tp. The heated section of the pipe wall is maintained at a constant heat flux so that a constant temperature difference of AT, = T, – T, exists between the wall and the bulk wa- ter temperature. Show that for turbulent flow in the pipe and a specified heated length and pipe diameter, water temperature at the exit of the heated section is given by: 402 0.6 Pr T52 =Tf +0.0876 L AT DO.8 0.2 marrow_forward
- Еxample 1.3 The pressure drop over a 30-m length of 1-cm-diameter horizontal pipe transporting water at 20°C is measured to be 2kPa. A laminar flow is assumed. Determine (a) the maximum velocity in the pipe, (b) the Reynolds number, (c) the wall shear stress, and (d) the friction factor. Solution to be worked in class Example 1.4 Consider a constant diameter pipe with oil flowing through it. SG of the oil =0.85, kinematic viscosity = 6X10“ m²/s, diameter = 15cm and discharge = 0.02 m/s. The center of the pipeline at the exit is 2m above that at the entry to the pipeline. Find the head loss in 100 m length of pipe and the pressure drop at the exit of the pipe.arrow_forwardTo cool a given room it is necessary to supply 4 ft³/s of air through a 5-in.-diameter pipe. Approximately how long is the entrance length in this pipe? Assume that air is at 60°F. le i ! ftarrow_forwardIn a small section of a piping system, water at temperature of plastic pipe with diameter of 15cm which is placed at a upward slope of 35° as shown in Figure Ql(a). A mercury manometer is used to measure the pressure different inside the pipe. A globe valve is installed on the pipe to control the water flow rate at 0035 m³/s. is enters à Globe Mercury 3 m Figure Q1(a) If the valve is fully opened and the volume flow rate is 0.035 m³/s, determine the height of mercury manometer. (i) If the plastic pipe is replaced by cast iron pipe, evaluate the new height of the mercury manometer. (ii)arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning