A cold plate is an active cooling device that is attached to a heat-generating system in order to dissipate the heat while maintaining the system at an acceptable temperature. It is typically fabricated from a material of high thermal conductivity,
Consider conditions for which equivalent heat-generatingsystems are attached to the top and bottom of the coldplate, maintaining the corresponding surfaces at the sametemperature
(a) Assuming fully developed turbulent flow throughout each channel, obtain a system of equations that maybe used to evaluate the total rate of heat transfer tothe cold plate. q. and the outlet temperature of thewater,
(b) Consider a cold plate of width W = 100 mm andheight H = 10 mm, with 10 square channels of width
Want to see the full answer?
Check out a sample textbook solutionChapter 8 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Fluid Mechanics: Fundamentals and Applications
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Introduction to Heat Transfer
Introduction To Finite Element Analysis And Design
Engineering Mechanics: Dynamics (14th Edition)
Fox and McDonald's Introduction to Fluid Mechanics
- Determine the mean heat-transfer coefficient and the quantity of heat transferred in water flowing in a horizontal tube 3 mm in diameter (d) and 2 m long (l), if ω = 0.3 m/sec; tf = 60 deg C and tω = 20 deg C. Constants: @ tf = 60oC, λf = 0.567 kcal/m-hr-oC; νf = 0.478 x 10-6 m2/sec β = 5.11 x 10-4 1/oC and Prf = 2.98. @ tω = 20oC, Pr? = 7.02arrow_forwardA thick-walled cylinder tubing of hard rubber having an inside radius of 20mm is being used as temporary cooling coil in a bath. Ice water is flowing rapidly through inside tube and the inside wall temperature is 274.9K. The outside surface temperature is 297.1K. A total of 14.65W must be removed from the bath by cooling coil. How many m of tubing are required?arrow_forward2, The internal diameter of a boiler generating tute is 4in. and the wall thickness is 0.375 in. In operation the external surrace film temperature is 26 Btu/hr . ft².°F, the internal film coefficient is 1700 Btu/hr.ft².°F and a 0.375 in. thickness scale having a conductivity of 0.6 Btu/hr.ft. °F is deposited on the inner surface of the tube. The metal conductivity is 26 Btu/hr.ft. °F, the furnace gas temperature is 2100 °F and the temperature of the water is 500 °F, calculate (a) the overall coefficient of heat transfer for the clean tube, (b) the overall heat transfer coefficient including the effect of the scale, (c) the external tube surface temperature before and after the scalearrow_forward
- Fluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 65℃ and length of 10 m. Surface conduction of hot fluid is 5.2W/(m^2℃) and thermal conductivity of brass is 12.84W/(m℃). Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84W/(m℃) . Outside of it, is a fluid with 45℃ with surface conductance of 3.2W/(m^2℃). Find the heat transfer from the hot fluid with temperature of 65℃ to fluid with temperature of 45℃.arrow_forwardIn the last step of a food supplement production, the food supplement is heated from 25C to 75C while passing through a 12.7 mm diameter thin-walled tube at a speed of 0.2 m / s. Proper heating is provided by an electric resistance heating system wrapped on the outer surface of the pipe. What is the heat flux in a pipe with a length of 10 m? The density of the fluid is given as 1000 kg / cubic meter , heat capacity 4000 J / kg-K, density 2x10^-3 kg / m-s, heat transfer coefficient 0.8 W / m-K and Prandtl number 10.arrow_forwardA square isothermal chip is of width 5mm on a side mounted in a substrate such that its side and back surfaces are well insulated, while the front surface is exposed to the flow of coolant at 15C. From reliability considerations, the chip temperature must not exceed 85C. If air is used as a coolant, h = 200W/m2. If a dielectric liquid is used as coolant, h = 3000W/m2. What is the difference in maximum allowable power through the chip between the two coolants? (answer in W) *arrow_forward
- 2.1. Consider the flow of oil at Ton in a 40-cm-diameter pipeline at an average velocity of 0.5 m/s. A 300-m-long section of the pipeline passes through icy waters of a lake at 0°C. Measurements indicate that the surface temperature of the pipe is very nearly 0°C. Disregarding the thermal resistance of the pipe material, determine (a) the temperature of the oil when the pipe leaves the lake, and (b) the rate of heat transfer from the oil p=893.5 kg/m³, Cp=1838 J/kg°C, k=0.146W/m°C, Pr=28750. D = 259,1× 10* m²/s Toil = 20 Carrow_forward5. Steam condensing on the outer surface of a thin-walled circular tube of 50 mm diameter and 6 m length maintains a uniform surface temperature of 100 C. Water flows through the tube at a rate of m= 0.25 kg/s, and its inlet and outlet temperatures are Tmi = 15 C and Tmo = 57C. What is the average convection coefficient associated with the water flow? Data: Pvater = 1000 kg/m³ ; c, = 4.2 kJ/kg-K.arrow_forwardLiquid ammonia is transported from a production plant to a processing center via a 0.6-m diameter pipeline at a mass flow rate of 0.15 kg/s. Surface temperature of the pipe is maintained 0°C by using a cooling jacket with ice-cold water. Ammonia enters the pipeline at -17°C and exits at -3°C. Assume the flow is both hydrodynamically and thermally fully developed in the pipe. What is the length of the pipe? 1857marrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning