EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Question
Chapter 7, Problem 7.65P
Interpretation Introduction
Interpretation:
The final solution volume and the shaft of the pump should be calculated.
Concept introduction:
The Bernoulli’s equation is given below
Where,
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
Two tanks are connected by a series of pipes as shown below. Tank 1 initially contains 150 grams of salt dissolved in 20 liters of water, while tank 2 contains 50 grams of salt dissolved in 10 liters of water. Beginning at time t = 0, pure water is pumped into tank 1 at a volumetric flow rate of 3 liters per minute. This causes brine to flow between the tanks, and to flow out of both tanks at the volumetric flow rates shown in the Fig. 2. Determine the salt concentration in each tank (C, and C2) at any time t>0.
A spent sulfuric acid solution is brought up to strength for a pickling process in a mixer. Spent solution at 3% sulfuric acid (by weight) is mixed with a 50% solution (by weight) to obtain the desired product concentration of 40% acid by weight. All are aqueous solutions. Determine all flowrates on the basis of 100 lbm/h of product. If the actual flow of the spent stream is 300 lbm/h, what must the flowrates of the streams be?
A spent sulfuric acid solution is brought up to strength for a pickling process in a mixer. Spent solution at 3% sulfuric acid (by weight) is mixed with a 50% solution (by weight) to obtain the desired product concentration of 40% acid by weight. All are aqueous solutions. Determine all flow rates on the basis of 100 lbm per hour of product. If the actual flow of the spent stream is 300 lbm per hour. What must the flow rates of the stream be?
Chapter 7 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 7 - A certain gasoline engine has an efficiency of...Ch. 7 - Prob. 7.2PCh. 7 - Prob. 7.3PCh. 7 - Prob. 7.4PCh. 7 - Liquid ethanol is pumped from a large storage tank...Ch. 7 - Air at 300°C and 130 kPa flows through a...Ch. 7 - Prob. 7.7PCh. 7 - Prob. 7.8PCh. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - Prob. 7.11PCh. 7 - Prob. 7.12PCh. 7 - A piston?tted cylinder with a 6-cm inner diameter...Ch. 7 - Prob. 7.14PCh. 7 - Prob. 7.15PCh. 7 - Prob. 7.16PCh. 7 - Prob. 7.17PCh. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - Prob. 7.20PCh. 7 - Air is heated from 25°C to 140°C prior to entering...Ch. 7 - Prob. 7.22PCh. 7 - Prob. 7.23PCh. 7 - Prob. 7.24PCh. 7 - Prob. 7.25PCh. 7 - The conversion of the kinetic energy of wind to...Ch. 7 - Prob. 7.27PCh. 7 - Prob. 7.28PCh. 7 - Liquid water is fed to a boiler at 24°C and 10 bar...Ch. 7 - Prob. 7.30PCh. 7 - Prob. 7.31PCh. 7 - Saturated steam at a gauge pressure of 2.0 bar is...Ch. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - Prob. 7.38PCh. 7 - Prob. 7.39PCh. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Jets of high-speed steam are used in spray...Ch. 7 - The following diagram shows a simpli?ed version of...Ch. 7 - Three hundred L/h of a 20 mole% C3H880 nC4H10gas...Ch. 7 - Air at 38°C and 97% relative humidity is to be...Ch. 7 - A mixture containing 65.0 mole% acetone (Ac) and...Ch. 7 - Superheated steam at T1(°C) and 20.0 bar is...Ch. 7 - Prob. 7.48PCh. 7 - Prob. 7.49PCh. 7 - Eight fluid ounces (1 qt = 32 oz) of a beverage in...Ch. 7 - Prob. 7.51PCh. 7 - Prob. 7.52PCh. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55PCh. 7 - Prob. 7.56PCh. 7 - Prob. 7.57PCh. 7 - Prob. 7.58PCh. 7 - Prob. 7.59PCh. 7 - Prob. 7.60PCh. 7 - Prob. 7.61PCh. 7 - Prob. 7.62PCh. 7 - Arsenic contamination of aquifers is a major...Ch. 7 - Prob. 7.64PCh. 7 - Prob. 7.65P
Knowledge Booster
Similar questions
- A gas mixture at 300K and 1 bar analyzing by volume 20% N2 and 80% CH4 is subjected to liquefaction at the rate of 1500 kg/hr. It is found that only 30% (weight) of the entering gas is liquefied and the concentration of N2 in the liquid is 60% by weight. The unliquefied gas leaves the unit at 273K and 1 bar. Determine (a) the volume of the unliquefied gas, m3/hr (b) the composition of the gas leaving expressed as volume %.arrow_forwardA 3.1 kg mass of saturated liquid-vapor mixture of water is contained within a closed system in a vertically arranged piston-cylinder device at a pressure of P1. Initially, 1.1067 kg of the water is in the liquid phase and the rest is in the vapor phase. Heat is now transferred to the water, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches P2. Heat transfer continues until the total volume increases by 19 percent. Consider Case #7 from Table 1: Table 1: Case # along with the list of pressures P, and P2 Case # P1 (kPa) P2 (kPa) 100 300 150 300 3 200 500 4 250 500 300 500 350 700 400 700 8. 450 700 (a) show the process on a P-v diagram in reference to the saturation lines, (b) determine the initial and final temperatures, (c) determine the mass of liquid water when the piston first starts moving, and (d) determine the work done during this process.arrow_forwardA solution containing 100 lbm KNO 3/100 lbm H 2O at 80°C is fed to a cooling crystallizer operated at 25°C. Slurry from the crystallizer (KNO3 crystals suspended in saturated solution) is fed to a filter, where the crystals are separated from the solution. Use the solubility data in Figure 6.5-1 to determine the production rate of crystals (lbm/lbm feed) and the solid-to-liquid mass ratio (lbm crystals/lbm liquid) in the slurry leaving the crystallizer.arrow_forward
- A brine solution of salt flows at a constant rate of 9 L/min into a large tank that initially held 100 L of brine solution in which was dissolved 0.4 kg of salt. The solution inside the tank is kept well stirred and flows out of the tank at the same rate. If the concentration of salt in the brine entering the tank is 0.04 kg/L, determine the mass of salt in the tank after t min. When will the concentration of salt in the tank reach 0.01 kg/L? Determine the mass of salt in the tank after t min, mass = | kgarrow_forwardA mixture of methane and air is capable of being ignited only if the mole percent of methane is between 5% and 15%. A mixture containing 9.0 mole% methane in air flowing at a rate of 7:00 x 102 kg/h is to be diluted with pure air to reduce the methane concentration to the lower flammability limit. Calculate the required flow rate of air in mol/h and the percent by mass of oxygen in the product gas. (Note: Air may be taken to consist of 21 mole% O2 and 79% N2 and to have an average molecular weight of 29.0.)arrow_forwardA single effect evaporator is used to concentrate 10 000 kg / hr of tomato juice from 5% total solids to 30% total solids. The juice enters the evaporator at 15 ° C. The evaporator is operated on Steam (80% quality) at 143.27 kPa. The vacuum in the evaporator allows the juice to boil at 75 ° C. The specific heat of the dilute material is 4.1 kJ / (kg ° C) and the concentrate product is 3.1 kJ / (kg ° C). Count it (a) Steam demand rate = Answer kg / hour. b. Steam economy when condensate temperature is released at 75 ° C. = Answer (kg of water evaporated / kg of steam)arrow_forward
- Q2: A stream of liquid water at a rate of N lit/s with a stream of methanol and ethanol mixture (contains 25 mol% methanol) are fed to continues evaporator. Another stream of methanol at a molar flow rate of G that of the alcohol mixture stream is fed to the same unit. If the liquids are evaporated totally and the produced vapor stream contains (0.1"G) mol% of water at a pressure of 28 psi and 220 F. calculate: 1- The flow rate and composition of all streams in a molar, mass, and volumetric basis 2- The average molecular mass of all streams The Specific gravity of methanol is 0.762 and that of ethanol is 0.789 while the density of vapors can be estimated as: p= p*Mw/RT where R-0.082 atm.m'/kmol.K.arrow_forwardA tank contains 400 liters of brine holding 100kg of salt in solution. Water containing 125g of salt per liter flows into the tank at the rate of 12 liters per minute, and the mixture, kept uniform by stirring, flows out at the same rate. Find the amount of salt at the end of 90 minutes.arrow_forwardSolve the problem systematically. All assumptions and references(s) for the values obtained should be indicated. Drawing-Given-Required-Solution A forward feed triple effect evaporator is used to fed 13608 kg/hr of NaOH solution containing 10 wtz solute. The entering feed temperature is 37.8°C. It is to be concentrated to a 50% NaOH solution. The steam used to enter at 58.6 kPa gage. The absolute pressure in the vapor space of the third effect is 6.76 kPa. The heat transfer coefficient are U.-6246, U-3407, and U₁-2271 W/mK. All effects must have the same area, Calculate the surface area and steam consumption (Hint: Assume no BPR at 1 and 2 effect)arrow_forward
- L-Serine is an amino acid important for its roles in synthesizing other amino acids and for its use in intravenous feeding solutions. It is often synthesized commercially by fermentation, and recovered by subjecting the fermentation broth to several processing steps and then crystallizing the serine from an aqueous solution. The solubilities of L-serine (L-Ser) in water have been measured at several temperatures, producing the following data:5T(K) 283.4 285.9 289.3 299.1 316.0 317.8 322.9 327.1x(mole fraction L-Ser) 0.0400 0.0426 0.0523 0.0702 0.1091 0.1144 0.1181 0.1248One of the ways such data can be represented is with the van’t Hoff equation: ln x =( a=T b).Graph the data so that the resulting plot is linear. Estimate a and b and give their units.arrow_forwardAbsorption of sulphur dioxide is carried out in a packed tower. Gas containing 14.8% sulphur dioxide and the rest inert gases enters the tower while the leaving gases contains 1% sulphur dioxide. Water flows at the rate of Im³/min. The tower handles 7380 m³/hr of gas at 303K and 1 bar. Find the kmoles of sulphur dioxide absorbed in the effluent from the tower. Also find the volume (m³) of the gases leaving the tower at 0.95 bar and 2983K.arrow_forwardA mixture of methane and air is capable of being ignited only if the mole percent of methane is between 5% and 15%. A mixture containing 6.00 mole% methane in air flowing at a rate of 1300.0 kg/h is to be diluted with pure air to reduce the methane concentration to the lower flammability limit. Calculate the required flow rate of air in mol/h and the percent by mass of oxygen in the product gas. (Note: Air may be taken to consist of 21.0 mole% O2 and 79.0 mole% N and hence to have an average molecular weight of 29.0). Required dilution air: 4/1ouy Mass percent O2 in product: iarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill EducationPrinciples of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
- Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill EducationChemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage LearningElementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305957404/9781305957404_smallCoverImage.gif)
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781259911156/9781259911156_smallCoverImage.gif)
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305577213/9781305577213_smallCoverImage.gif)
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9780078021558/9780078021558_smallCoverImage.gif)
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305079373/9781305079373_smallCoverImage.gif)
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118431221/9781118431221_smallCoverImage.gif)
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY