EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 7, Problem 7.47P
Superheated steam at T1(°C) and 20.0 bar is blended with saturated steam at T2(°C) and 10.0 bar in a ratio (1.96 kg of steam at 20 bar)/( 1.0 kg of steam at 10 bar). The product stream is at 250°C and
10.0 bar. The process operates at steady state.
(a) Calculate T1and T2, assuming that the blender operates adiabatically.
(b) If in fact heat is being lost from the blender to the surroundings, is your estimate of T1too high or too low? Briefly explain.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The gas A(g) (1 mole) undergoes a two-step process one after another as described below :i) The gas is expanded at 25°C and from 1 bar pressure against a constant pressure of 0.2 bar and the final volume of the gas is the twice the initial volume.ii) The gas is cooled down to -25°C at constant volume.Cv,m = 3/2 RCalculate ΔU, ΔH, q and w for the each step and for the entire process
3.
A gas contained within a closed piston-cylinder assembly undergoes three processes in series:
Process 1-2: Constant volume from P₁ = 1 bar, V₁ = 4 m³ to state 2, where P₂ = 2 bar;
Process 2-3: Compression to V3 = 2 m³, during which the pressure-volume relationship is PV =
constant;
Process 3-4: Constant pressure to state 4, where V4 = 1 m³;
(a) Sketch the processes in series on P-V coordinates.
(b) Evaluate the magnitude of work in kJ for EACH process. To make the unit consistent, you might need
to convert the unit of pressure from bar to Pa.
=
1. A process has been proposed whereby an ideal gas is taken from P 10 bar and T = 300
K to P
-
1 bar and T = 500 K in a closed system. During the process the system (ideal gas)
does 1,000 kJ of work and receives 5,430 kJ of heat from the surroundings. The temperature
of the surroundings is constant at 300 K.
Cp
Ideal gas heat capacity: = 3.6 + 0.5 * 10-³T
R
(c)
(T in K)
Calculate the change in entropy of the surroundings.
Chapter 7 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 7 - A certain gasoline engine has an efficiency of...Ch. 7 - Prob. 7.2PCh. 7 - Prob. 7.3PCh. 7 - Prob. 7.4PCh. 7 - Liquid ethanol is pumped from a large storage tank...Ch. 7 - Air at 300°C and 130 kPa flows through a...Ch. 7 - Prob. 7.7PCh. 7 - Prob. 7.8PCh. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - Prob. 7.11PCh. 7 - Prob. 7.12PCh. 7 - A piston?tted cylinder with a 6-cm inner diameter...Ch. 7 - Prob. 7.14PCh. 7 - Prob. 7.15PCh. 7 - Prob. 7.16PCh. 7 - Prob. 7.17PCh. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - Prob. 7.20PCh. 7 - Air is heated from 25°C to 140°C prior to entering...Ch. 7 - Prob. 7.22PCh. 7 - Prob. 7.23PCh. 7 - Prob. 7.24PCh. 7 - Prob. 7.25PCh. 7 - The conversion of the kinetic energy of wind to...Ch. 7 - Prob. 7.27PCh. 7 - Prob. 7.28PCh. 7 - Liquid water is fed to a boiler at 24°C and 10 bar...Ch. 7 - Prob. 7.30PCh. 7 - Prob. 7.31PCh. 7 - Saturated steam at a gauge pressure of 2.0 bar is...Ch. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - Prob. 7.38PCh. 7 - Prob. 7.39PCh. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Jets of high-speed steam are used in spray...Ch. 7 - The following diagram shows a simpli?ed version of...Ch. 7 - Three hundred L/h of a 20 mole% C3H880 nC4H10gas...Ch. 7 - Air at 38°C and 97% relative humidity is to be...Ch. 7 - A mixture containing 65.0 mole% acetone (Ac) and...Ch. 7 - Superheated steam at T1(°C) and 20.0 bar is...Ch. 7 - Prob. 7.48PCh. 7 - Prob. 7.49PCh. 7 - Eight fluid ounces (1 qt = 32 oz) of a beverage in...Ch. 7 - Prob. 7.51PCh. 7 - Prob. 7.52PCh. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55PCh. 7 - Prob. 7.56PCh. 7 - Prob. 7.57PCh. 7 - Prob. 7.58PCh. 7 - Prob. 7.59PCh. 7 - Prob. 7.60PCh. 7 - Prob. 7.61PCh. 7 - Prob. 7.62PCh. 7 - Arsenic contamination of aquifers is a major...Ch. 7 - Prob. 7.64PCh. 7 - Prob. 7.65P
Additional Science Textbook Solutions
Find more solutions based on key concepts
Revisit Example 1-1. Rework this example using Equation (3-1) on page 71.
Revisit Example 1-2. Calculate the vo...
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
Appelpolscher has just left a meeting with Stella J. Smarly, IGC’s vice-president for process operations anddev...
Process Dynamics and Control, 4e
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Three 150 mm 300 mm concrete cylinders with water to cement ratios of 0.4, 0.6, and 0.8, respectively. After c...
Materials for Civil and Construction Engineers (4th Edition)
Two models are applied to a dataset that has been partitioned. Model A is considerably more accurate than model...
Data Mining for Business Analytics: Concepts, Techniques, and Applications with XLMiner
The ________ object is assumed to exist and it is not necessary to include it as an object when referring to it...
Web Development and Design Foundations with HTML5 (9th Edition) (What's New in Computer Science)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- (5) The emissions from a manufacturing process contain gaseous pollutant that cause odors and fumes. The company plans to incinerate the 5,000 acfm exhaust stream. Estimate the volumetric (standard) flowrate of natural gas fuel required to increase the waste gas stream temperature from the initial 80°F to the required temperature of 2500°F. Energy (enthalpy) is transferred from the fuel to the gas. Neglect any possible heat losses in this process. The average net heating value of natural gas is 850 - 1050 Btu/std-ft. Include a diagram of the scenario.arrow_forward9 (a) Liquid octane is burnt in 30% excess air in a steady flow combustion chamber at a pressure of 1 atmosphere. Determine the heat given off per kilo mole of octane if the reactants and products are both maintained at 25°C and the water in the combustion products is in the (i) liquid form (ii) vapour form. (b) Liquid octane and theoretical air at 1 bar and 25°C react in a steady flow process under stoichiometric conditions. If the combustion is well insulated, determine the adiabatic temperature with water in the products in (i) liquid phase and (ii) vapour phase.arrow_forwardA tank containing carbon dioxide at 400K and 50 bar is vented until the temperature in the tank falls to 300K. Assuming there is no heat transfer between the gas and the tank, find the pressure in the tank at the end of the venting process and the fraction of the initial mass of gas remaining in the tank for each of the following cases. a) the equation of state of carbon dioxide is P(V_mol-b)=R*T. b) Carbon dioxide obeys the law of corresponding states. c) Carbon dioxide obeys the Peng-Robinson equation of state.arrow_forward
- Q1) A constant volume tank contain 1 mole ofC7H14and 12 mole of O2 gas at a temperature of 25 °C and 1 bar. The contents of the tank is ignited and C7H14 is burned completely and final products temperature is found to be 1700 K. Determine the heat transfer during this process. ( take daltaHo = -47800 kJ/kg).arrow_forwardFor each of the following processes that occur in an open steady state system, calcu- late the heat transfer to or from the system if it is isothermal. (a) 1000 g of O₂ are mixed with 1000 g of CO₂- (b) 900 kg of water are mixed with 63 kg of nitric acid. Data at SC: Compound Ĥ (kJ/kg) HNO3 (liquid) - 173.234 In 1 g mol H₂O -186.347 2 H₂O - 193.318 5 H₂O -201.962 10 H₂O -205.014 50 H₂O -205.978 100 H₂O -205.983arrow_forwardA closed system consisting of 2 lb of a gas undergoes a process during which the relation between pressure and volume is pV" = constant. The process begins with p₁= 15 lbf/in.2. v₁ = 1.25 ft3/lb and ends with p₂ = 60 lbf/in.2, v₂ = 0.5 ft3/lb. Determine (a) the volume, in ft², occupied by the gas at states 1 and 2 and (b) the value of n. Determine the volume, in ft, occupied by the gas at states 1 and 2. V₁= V₂ = Determine the value of n. n= 1 2 ft³ ft3arrow_forward
- A vessel of capacity 0.3 m3 is insulated and divided into two sections by a partition. One section is 0.2 m3in volume and initially contains H2at 2 bar and 127°C. The remaining section initially holds N2at 4 bar and27°C. The adiabatic partition is then removed, and the gases are allowed to mix. Determine : (i) The temperature of the equilibrium mixture,(ii) The pressure of the mixture, and(iii) The change in entropy for each component and total value.cv(N ) 2 = 0.744 kJ/kg K, cv(H ) 2 = 10.352 kJ/kg Kcp(N ) 2 = 1.041 kJ/kg K, cp(N ) 2 = 14.476 kJ/kg K.arrow_forwardQ1) A constant volume tank contain 1 mole of C,H14 and 12 mole of O2 gas at a temperature of 25 °C and 1 bar. The contents of the tank is ignited and C8H18is burned completely and final products temperature is found to be 1700 K. Determine the heat transfer during this process. ( take AHo = -47800 kJ/kg).arrow_forward3. A device is being designed to separate a natural gas having a molar analysis of 94% CH4 and 6% C2H6 into components. The device will receive natural gas at 208C, 1 atm with a volumetric flow rate of 100 m3/s. Separate streams of CH4 and C2H6 will exit, each at 208C, 1 atm. The device will operate isothermally at 208C. Ignoring kinetic and potential energy effects and assuming ideal gas behavior, determine the minimum theoretical work input required at steady state, in kW.arrow_forward
- 3. Heat capacities are usually given in terms of polynomial functions of temperature. The equation for the heat capacity of an ionic liquid is where T(R) and Cp (Btu Ibmol-1 R-1). Cp = 8.448 + 0.5757 × 10-2T+7.693 × 10-³ T log(0.325 T) (a) Determine the units of the constants (b) Develop an equation to calculate Cp in (Jxgmol-¹xK-1) as a function of Tin K. Express the coefficients in scientific notation and in four (4) significant figures.arrow_forwardAn ideal gas with CP = (5/2)R CV=(3/2) is changed from P1 = 1 bar and V1 = 10 m³ to P2 = 10 bar and V2 = 1 m3 by the following mechanically reversible processes: %3D %3D .Isothermal compression (a) Adiabatic compression followed by cooling at constant (b) .pressure © Adiabatic compression followed by cooling at constant .volume Heating at constant volume followed by cooling at (c) .constant pressure € Cooling at constant pressure followed by heating at .constant volume Calculate Q, W, Aut, and AHt for each of these processes, and .sketch PV diagramarrow_forwardSteam (H₂O vapor) flows in a pipeline in a power station. The steam pressure is 180 psia, its temperature is 400°F, and it flows with velocity 750 ft/s. Calculate the stagnation pressure and stagnation temperature. Assume that the steam is an ideal gas with a molecular weight of 18 and k = 1.3. To = °R Po = psi(abs.)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY
Introduction to Nonreactive Processes Without Phase Change; Author: NPTEL-NOC IITM;https://www.youtube.com/watch?v=1Okp7895M6I;License: Standard YouTube License, CC-BY