EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 5, Problem 5.21P
Interpretation Introduction
Interpretation:
The mole percentage of CO2 in the product stream should be calculated.
Concept introduction:
The
Where, the volume (V) occupied by ‘n’ moles of any gas has a pressure (P) at temperature (T) in Kelvin and ‘R’ = Gas constant
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A gas mixture at 300K and 1 bar analyzing by volume 20% N2 and 80% CH4 is subjected to liquefaction at the rate of 1500 kg/hr. It is found that only 30% (weight) of the entering gas is liquefied and the concentration of N2 in the liquid is 60% by weight. The unliquefied gas leaves the unit at 273K and 1 bar. Determine (a) the volume of the unliquefied gas, m3/hr (b) the composition of the gas leaving expressed as volume %.
A gas mixture contains 10.0 mole% H 2O(v) and 90.0 mole% N 2. The gas temperature and absolute pressure at the start of each of the three parts of this problem are 50°C and 500 mm Hg. Ideal-gas behavior may be assumed in every part of this problem.(a) If some of the gas mixture is put in a cylinder and slowly cooled at constant pressure, at what temperature would the first drop of liquid form?(b) If a 30.0-liter flask is filled with some of the gas mixture and sealed and 70% of the water vapor in the flask is condensed, what volume (cm 3 ) would be occupied by the liquid water? What would be the system temperature?(c) If the gas mixture is stored in a rigid-walled cylinder and a low-pressure weather front moves in and the barometric (atmospheric) pressure drops, which of the following would change: (i) the gas density, (ii) the absolute pressure of the gas, (iii) the partial pressure of water in the gas, (iv)the gauge pressure of the gas, (v) the mole fraction of water in the gas, (vi)…
Two closed tanks are connected to each other by a valve. The first tank contains oxygen (O₂, m= 2.4 kg, T= 134 °C, p= 5 bar) and
the other carbon dioxide (CO₂, m= 2.4 kg, T = 33 °C, p = 1.0 bar). When the valve is opened, the gases are allowed to mix. When
the mixture reaches equilibrium, the temperature of the mixture is 73 °C. The gases can be assumed to be ideal gases.
Calculate
m³ (two decimal accuracy)
1) Total volume of the tanks
2) Final pressure of the mixture
3) Molar fraction of oxygen in the mixture
4) Molar fraction of carbon dioxide in the mixture
5) Partial pressure of oxygen in the mixture
6) Partial pressure of carbon dioxide in the mixture
7) Average specific heat capacity of oxygen at constant volume
8) Average specific heat capacity of carbon dioxide at constant volume
9) Heat transferred from or to the process
kPa (zero decimal accuracy)
% (zero decimal accuracy)
% (zero decimal accuracy)
kPa (zero decimal accuracy)
kPa (zero decimal accuracy)
kJ/kgk (three decimal…
Chapter 5 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 5 - A liquid mixture containing 40.0 wt% n-octane and...Ch. 5 - Prob. 5.2PCh. 5 - Prob. 5.3PCh. 5 - Prob. 5.4PCh. 5 - Prob. 5.5PCh. 5 - Prob. 5.6PCh. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - Prob. 5.9PCh. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - Prob. 5.12PCh. 5 - Prob. 5.13PCh. 5 - Prob. 5.14PCh. 5 - Prob. 5.15PCh. 5 - Prob. 5.16PCh. 5 - Prob. 5.17PCh. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - A device has been designed to measure the flow...Ch. 5 - Prob. 5.21PCh. 5 - Prob. 5.22PCh. 5 - Spray drying is a process in which a liquid...Ch. 5 - Prob. 5.24PCh. 5 - Lewis12 describes the hazards of breathing air...Ch. 5 - A stream of air at 35°C and a gauge pressure of...Ch. 5 - Prob. 5.27PCh. 5 - In froth ?otation, air is bubbled through an...Ch. 5 - Prob. 5.29PCh. 5 - Prob. 5.30PCh. 5 - Bread is typically made by ?rst dissolving...Ch. 5 - Prob. 5.32PCh. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - A spray-drying operation similar to that described...Ch. 5 - Prob. 5.41PCh. 5 - Fermentation is a biochemical process in which a...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - Ethane at 25°C and 1.1 atm (abs) flowing at a rate...Ch. 5 - The ?ow of air to a gas-?red boiler furnace is...Ch. 5 - Prob. 5.47PCh. 5 - The oxidation of nitric oxide NO+12O2NO2 takes...Ch. 5 - Prob. 5.49PCh. 5 - 5.50.19 In chemical vapor deposition (CVD), a...Ch. 5 - A gas turbine power plant receives a shipment of...Ch. 5 - Prob. 5.52PCh. 5 - 5.53.20 Chemicals are stored in a laboratory with...Ch. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - A stream of ho dry nitrogen flows through a...Ch. 5 - Prob. 5.57PCh. 5 - You have purchased a gas cylinder that is supposed...Ch. 5 - The current global reliance on fossil fuels for...Ch. 5 - Two humid gas streams are combined in a heated...Ch. 5 - Most of the concrete used in the construction of...Ch. 5 - The ultimate analysis of a No. 4 fuel oil is 86.47...Ch. 5 - A stream of liquid n-pentane flows at a rate of...Ch. 5 - Alka-Seltzer( is an over-the-counter medicine used...Ch. 5 - Hydrogen sul?de has the distinctive unpleasant...Ch. 5 - The quantity of sulfuric acid used globally places...Ch. 5 - A small power plant produces 500 MW of electricity...Ch. 5 - You have been assigned the task of measuring the...Ch. 5 - Prob. 5.69PCh. 5 - Methanol is synthesized from carbon monoxide and...Ch. 5 - Prob. 5.71PCh. 5 - Prob. 5.72PCh. 5 - Steam reforming is an important technology for...Ch. 5 - A ?owchart of a methanol synthesis process is...Ch. 5 - The measured volumetric flow rate of ethane at...Ch. 5 - Prob. 5.76PCh. 5 - Methanol is to be delivered to a process unit at a...Ch. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - Prob. 5.82PCh. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - Prob. 5.85PCh. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - Prob. 5.89PCh. 5 - A fuel cell is an electrochemical device that...Ch. 5 - In a metered-dose inhaler (MDI), such as those...Ch. 5 - Prob. 5.92PCh. 5 - Prob. 5.93PCh. 5 - Approximately 150 SCFM (standard cubic feet per...Ch. 5 - Prob. 5.95PCh. 5 - Prob. 5.96PCh. 5 - Prob. 5.97PCh. 5 - The product gas from a coal gasification plant...Ch. 5 - Prob. 5.99PCh. 5 - Prob. 5.100PCh. 5 - A gas mixture consisting of 15.0 mole% methane....Ch. 5 - A system has been devised to store acetonitrile...Ch. 5 - Prob. 5.103PCh. 5 - Prob. 5.104P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- 3. A gas contained within a closed piston-cylinder assembly undergoes three processes in series: Process 1-2: Constant volume from P₁ = 1 bar, V₁ = 4 m³ to state 2, where P₂ = 2 bar; Process 2-3: Compression to V3 = 2 m³, during which the pressure-volume relationship is PV = constant; Process 3-4: Constant pressure to state 4, where V4 = 1 m³; (a) Sketch the processes in series on P-V coordinates. (b) Evaluate the magnitude of work in kJ for EACH process. To make the unit consistent, you might need to convert the unit of pressure from bar to Pa.arrow_forwardThe boiler in an apartment building uses propane (C3H8) to heat water that circulates throughout the building as steam. 1.00 m'/s of propane gas at 25°C and 1 atm is combusted with 10% excess air at 25°C and 1 atm. After all of the propane is combusted, the product gas contains a 10.0:1 molar ratio of CO2 to CO and leaves the boiler at 25°C. Heat from the boiler is transferred to a pure water stream at 50°C and 1.0 bar, which is converted into saturated steam at 20 bar, with no heat lost to the surroundings in the process. What mass of water is heated in this process? Molecule (Formula) (kJ/mol) -393.5 (g) Carbon dioxide (CO2) Carbon -110.52 (g) monoxide (CO) Hydrogen (H2) Nitrogen (N2) Охуgen (O2) Propane (C;Hs) Hot Water (out). Flue Gas Shutoff Valve - Cold Water (in) -119.8(1) -103.8(g) -285.84(1) Gas Supply Line- Cold Water Shutoff Valve Water (H20) -241.83(g) Temperature / Pressure Relief Valve Water Line Overflow Pipe. Tank Insulation - Dip Tube Drain Valve Gas Burner Control-…arrow_forwardA mixture of phenol and water, under certain conditions of temperature and composition, forms two separate liquid phases, one rich in phenol and the other rich in water. At 30⁰ the compositions of the upper and lower layers are 70% and 9% by mass phenol, respectively. If 40kg of phenol and 60kg of water are mixed and the layers are allowed to separate at 30⁰C, what will be the weight of the two layers?arrow_forward
- A gaseous fuel containing methane and ethane is burned with excess air. The fuel enters the furnace at 25°C and 1 atm, and the air enters at 200°C and 1 atm. The stack gas leaves the furnace at 800°C and 1 atm and contains 5.32 mole% CO2, 1.60% CO, 7.32% O₂, 12.24% H₂O, and the balance ₂. 1. Calculate the molar percentages of methane and ethane in the fuel gas and the percentage excess air fed to the reactor. 2. Calculate the heat (kJ) transferred from the reactor per cubic meter of fuel gas fed. 3. A proposal has been made to lower the feed rate of air to the furnace. State advantages and a drawback of doing so.arrow_forwardA solid fuel, described by the chemical structure below, is combusted in 10% excess air. If necessary, clearly state any assumptions required to develop your solution. H Н —с — N — с — s — н | || 0 = C S H (a) Determine the mass feed rate (g/min) of the fuel such that 10,000 m³/min of total flue gas is generated at 1500 °C and 1 atm. (b) Determine the effluent SO2 concentration (ppm,) at STP and dry conditions.arrow_forwardCarbonic anhydrase of erythrocytes (Mr 30,000) has one of the highest turnover numbers known. It catalyzes the reversible hydration of CO2:This is an important process in the transport of CO2 from the tissues to the lungs. If 10.0 μg of pure carbonic anhydrase catalyzes the hydration of 0.30 g of CO2 in 1 min at 37 °C at Vmax , what is the turnover number (kcat) of carbonic anhydrase (in units of min −1 )?arrow_forward
- (5) The emissions from a manufacturing process contain gaseous pollutant that cause odors and fumes. The company plans to incinerate the 5,000 acfm exhaust stream. Estimate the volumetric (standard) flowrate of natural gas fuel required to increase the waste gas stream temperature from the initial 80°F to the required temperature of 2500°F. Energy (enthalpy) is transferred from the fuel to the gas. Neglect any possible heat losses in this process. The average net heating value of natural gas is 850 - 1050 Btu/std-ft. Include a diagram of the scenario.arrow_forwardCalculate (1) partial pressures, (2) mole fractions, (3) Concentrations, (4) densities of the gaseous components in a vessel, which contains 0.2 kg of H₂, 3 mol of CO, amount of H₂O vapor enough to give partial pressure of 1 bar (105 Pa). Pressure and temperature of the perfect gaseous mixture in the vessel: P = 3 bar; T = 500 K.arrow_forward4.64. The gas-phase reaction between methanol and acetic acid to form methyl acetate and water CH;OH + CH3COOH = CH3COOCH3 + H2O (A) (В) (C) (D) takes place in a batch reactor. When the reaction mixture comes to equilibrium, the mole fractions of the four reactive species are related by the reaction eqilibrium constant Ky : = 4.87 YAYB (a) Suppose the feed to the reactor consists of n40,NB0, NCo, NDO, and no gram-moles of A, B, C, D, and an inert gas, I, respectively. Let į be the extent of reaction. Write expressions for the gram-moles of each reactive species in the final product, nA(2), nB(3), nc(E), and np(3). Then use these expressions and the given equilibrium constant to derive an equation for , the equilibrium extent of reaction, in terms of n20,.., N1o. (see Example 4.6-2.) (b) If the feed to the reactor contains equimolar quantities of methanol and acetic acid and no other species, calculate the equilibrium fractional conversion. (c) It is desired to produce 70 mol of methyl…arrow_forward
- You have analyzed an aqueous ammonia solution and find that it contains 30 wt% NH 3.(a) to determine the mass fraction of NH 3 in the vapor that would be in equilibrium with this solution in a closed flask at 1 atm and the corresponding system temperature.(b) If the liquid phase in Part (a) accounts for 90% of the total system mass, calculate the overall system composition and specific enthalpy using balances.arrow_forwardTe (K) (bar)| (Pa (m/kmol)²) | (m³/kmol) 190.6| 46 305.3 49 |369.5 42.5 Pe a b Natural gas is produced in a gas field outside of the City of Grande Prairie and is delivered through a pipeline to a sales point. At the sales point, the pressure in the pipeline is 5 MPa Propane and the temperature is 20°C. The natural gas is composed of 85 mol% methane, 10 mol% ethane and 5 mol% propane. Selected properties of these components have been provided in the table above. Using the information provided, answer the questions below. Component Methane Ethane 5.56x105 0.0638 8.78x10 0.0845 m3 m3 (c) Calculate the values of a (in Pa· ) and b (in ) for the mixture. kmol, kmol,arrow_forwardA mixture of methane and air is capable of being ignited only if the mole percent of methane is between 5% and 15%. A mixture containing 9.0 mole% methane in air flowing at a rate of 7:00 x 102 kg/h is to be diluted with pure air to reduce the methane concentration to the lower flammability limit. Calculate the required flow rate of air in mol/h and the percent by mass of oxygen in the product gas. (Note: Air may be taken to consist of 21 mole% O2 and 79% N2 and to have an average molecular weight of 29.0.)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY