EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 5, Problem 5.6P
Interpretation Introduction
(a)
Interpretation:
An expression for the transducer reading should be derived.
Concept introduction:
Pressure of a liquid open to atmosphere can be written as,
Where, Patm is the atmospheric pressure, h is height of the liquid column and ? is density of liquid
Interpretation Introduction
(b)
Interpretation:
The given expression should be validated.
Concept introduction:
Pressure of a liquid open to atmosphere can be written as,
Where, Patm is the atmospheric pressure, h = height of the liquid column and ? = density of liquid
In addition, the equation can be validated by checking the units.
Interpretation Introduction
(c)
Interpretation:
The following variables should be calculated.
- The total slurry volume
- The mass of crystals in the slurry
- The mass of anhydrous copper sulfate
- Mass of liquid solution
- The volume of liquid solution
Concept introduction:
Pressure of a liquid open to atmosphere can be written as,
Where, Patm is the atmospheric pressure, h = height of the liquid column and ? = density of liquid
In addition, the equation can be validated by checking the units.
Interpretation Introduction
(d)
Interpretation:
A calibration curve for this device should be prepared.
Concept introduction:
Pressure of a liquid open to atmosphere can be written as,
Where, Patm is the atmospheric pressure, h = height of the liquid column and ? = density of liquid
In addition, the equation can be validated by checking the units.
Interpretation Introduction
(e)
Interpretation:
The expression in part (b) should be derived
Concept introduction:
Pressure of a liquid open to atmosphere can be written as,
Where, Patm is the atmospheric pressure, h = height of the liquid column and ? = density of liquid
In addition, the equation can be validated by checking the units.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A solid fuel, described by the chemical structure below, is combusted in 10% excess air. If
necessary, clearly state any assumptions required to develop your solution.
H
Н —с — N — с — s — н
|
||
0 = C
S
H
(a) Determine the mass feed rate (g/min) of the fuel such that 10,000 m³/min of total flue
gas is generated at 1500 °C and 1 atm.
(b) Determine the effluent SO2 concentration (ppm,) at STP and dry conditions.
volume reactants
gas
products
Na₂CO3 (s) + 2 HCI (aq)
solution
mass
separate
layer
gram
liquid
solid coefficient
CO₂ (g) + H₂O (1) + 2 NaCl (aq)|
Refer to the ternary phase diagram in Fig. 5E.4. How many phases are present, and what are their compositions and relative abundances, in a mixture that contains 55.0 g of water, 8.8 g of trichloromethane, and 3.7 g of ethanoic acid? Describe what happens when (i) water, (ii) ethanoic acid is added to the mixture.
Chapter 5 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 5 - A liquid mixture containing 40.0 wt% n-octane and...Ch. 5 - Prob. 5.2PCh. 5 - Prob. 5.3PCh. 5 - Prob. 5.4PCh. 5 - Prob. 5.5PCh. 5 - Prob. 5.6PCh. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - Prob. 5.9PCh. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - Prob. 5.12PCh. 5 - Prob. 5.13PCh. 5 - Prob. 5.14PCh. 5 - Prob. 5.15PCh. 5 - Prob. 5.16PCh. 5 - Prob. 5.17PCh. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - A device has been designed to measure the flow...Ch. 5 - Prob. 5.21PCh. 5 - Prob. 5.22PCh. 5 - Spray drying is a process in which a liquid...Ch. 5 - Prob. 5.24PCh. 5 - Lewis12 describes the hazards of breathing air...Ch. 5 - A stream of air at 35°C and a gauge pressure of...Ch. 5 - Prob. 5.27PCh. 5 - In froth ?otation, air is bubbled through an...Ch. 5 - Prob. 5.29PCh. 5 - Prob. 5.30PCh. 5 - Bread is typically made by ?rst dissolving...Ch. 5 - Prob. 5.32PCh. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - A spray-drying operation similar to that described...Ch. 5 - Prob. 5.41PCh. 5 - Fermentation is a biochemical process in which a...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - Ethane at 25°C and 1.1 atm (abs) flowing at a rate...Ch. 5 - The ?ow of air to a gas-?red boiler furnace is...Ch. 5 - Prob. 5.47PCh. 5 - The oxidation of nitric oxide NO+12O2NO2 takes...Ch. 5 - Prob. 5.49PCh. 5 - 5.50.19 In chemical vapor deposition (CVD), a...Ch. 5 - A gas turbine power plant receives a shipment of...Ch. 5 - Prob. 5.52PCh. 5 - 5.53.20 Chemicals are stored in a laboratory with...Ch. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - A stream of ho dry nitrogen flows through a...Ch. 5 - Prob. 5.57PCh. 5 - You have purchased a gas cylinder that is supposed...Ch. 5 - The current global reliance on fossil fuels for...Ch. 5 - Two humid gas streams are combined in a heated...Ch. 5 - Most of the concrete used in the construction of...Ch. 5 - The ultimate analysis of a No. 4 fuel oil is 86.47...Ch. 5 - A stream of liquid n-pentane flows at a rate of...Ch. 5 - Alka-Seltzer( is an over-the-counter medicine used...Ch. 5 - Hydrogen sul?de has the distinctive unpleasant...Ch. 5 - The quantity of sulfuric acid used globally places...Ch. 5 - A small power plant produces 500 MW of electricity...Ch. 5 - You have been assigned the task of measuring the...Ch. 5 - Prob. 5.69PCh. 5 - Methanol is synthesized from carbon monoxide and...Ch. 5 - Prob. 5.71PCh. 5 - Prob. 5.72PCh. 5 - Steam reforming is an important technology for...Ch. 5 - A ?owchart of a methanol synthesis process is...Ch. 5 - The measured volumetric flow rate of ethane at...Ch. 5 - Prob. 5.76PCh. 5 - Methanol is to be delivered to a process unit at a...Ch. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - Prob. 5.82PCh. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - Prob. 5.85PCh. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - Prob. 5.89PCh. 5 - A fuel cell is an electrochemical device that...Ch. 5 - In a metered-dose inhaler (MDI), such as those...Ch. 5 - Prob. 5.92PCh. 5 - Prob. 5.93PCh. 5 - Approximately 150 SCFM (standard cubic feet per...Ch. 5 - Prob. 5.95PCh. 5 - Prob. 5.96PCh. 5 - Prob. 5.97PCh. 5 - The product gas from a coal gasification plant...Ch. 5 - Prob. 5.99PCh. 5 - Prob. 5.100PCh. 5 - A gas mixture consisting of 15.0 mole% methane....Ch. 5 - A system has been devised to store acetonitrile...Ch. 5 - Prob. 5.103PCh. 5 - Prob. 5.104P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- For this heterogeneous system 2 A(aq) + 3 B(g) + C(1) 2D(s) + 3 E(g) the concentrations and pressures at equilibrium are [A] = 1.69 x 10-2 M, PB = 7.28 x 10³ Pa, [C] = 14.39 M, [D] = 18.47 M, and PE = 4.45 x 104 torr. Calculate the thermodynamic equilibrium constant, K. K =arrow_forwardIf there was a leak in the syringe and gas was escaping as the syringe plunger was being compressed. Which equation could you use to figure out what this would do to the k value? ○ PV=k ○ P/T =k O P/V = k PT=k PT = karrow_forwardWhat is meant by Centrifugation and How to calculate a desire RCF and rpm for the separation of mixture of liquids?arrow_forward
- Pressure (A) Explain the term pressure and state its S.I. unit. (B) Explain Henry’s law. (C)A bottle of H2 has just been received by the technicians in DkIT for use in the instrumentation lab. It is a 47 litre cylinder at a pressure of 50 atmospheres. The normal working pressures is 2 bar. (i) To what volume of gas will that equate at the working pressure? (ii) For how many hours will the gas last if it used at the rate of 0.5dm3 per hour? D)You see your best friend at the bar and you walk up behind her. You accidentally startle her and she takes a step backwards. Unfortunately, she is wearing high heels and her heels come down on your foot. She weighs only 55kg but the size of her heel is 6mm by 6mm.Determine the pressure that she applies on your foot. (E) If a diver dives to a depth of 35 m what will be: (i) the pressure in Pascals due the water column? (3 marks) (ii) the pressure of the air in…arrow_forwardPart F The third variable (call it v) is v=x1-cx2 + x3, where c is a constant you need to determine so that the equation for v is the SHM equation. Determine v. The solution to the equation for vis v = 2B cos(t + b). Express your answer in terms of some, all, or none of the variables 21, 22, 23, and the appropriate constants. v = ΜΕ ΑΣΦ Submit Request Answer ?arrow_forwardThe following relation describes the volume change in a water (solvent – species 1) and salt (solute – species 2) solution: V=1.001+16.625n2 +56.092 n23/2 +119.4n22 where V is expressed in units of liters, and n2 in kmole. (1) Obtain an expression for partial V2 in terms of n2, and determine partial V2 when x2 is approching 0 in liter per kmole. (2) Obtain an expression for partial V1 one in terms of n2, and one in terms of x1.arrow_forward
- One of the more commonly used compressed gases is nitrogen (N2), often in large metal cylinders. If a cylinder holds 711 mol of N2 when pressurised to 5.3 x 104 kPa at T = 20oC, how many litres is its capacity?arrow_forwardP1A.5 Deduce the relation between the pressure and mass density, p, of a perfect gas of molar mass M. Confirm graphically, using the following data on methoxymethane (dimethyl ether) at 25°C, that perfect behaviour is reached at low pressures and find the molar mass of the gas. p/kPa 12.223 25.20 36.97 60.37 85.23 101.3 p/(kgm) 0.225 0.456 0.664 1.062 1.468 1.734arrow_forwardb) A gaseous mixture contain 32.9 mol % He, 40.7 mol % N2 and 26.4 mol % Ar. Determine the composition of this mixture on a mass basis based on the molecular weight given: MW (He) = 4.003 , MW (N2) = 28.02, MW(Ar) = 39.95 %3Darrow_forward
- Consider the following reaction CS2(9) + 302(9) – CO2(9) + 2SO2(g) A mixture containing only CS2(g) and excess O2(g) at a total pressure of 100 kPa is placed in a sealed vessel. After the reaction is completed and the vessel is cooled to the initial temperature, the total pressure in the vessel drops to 80 kPa. What was the mole fraction of CS2(g) in the initial mixture? A. 0.80 B. 0.50 C. 0.20 D. 0.75 E. 0.25arrow_forwardP1A.6 The molar mass of a newly synthesized fluorocarbon was measured in a gas microbalance. is device consists of a glass bulb forming one end of a beam, the whole surrounded by a closed container. The beam is pivoted, and the balance point is attained by raising the pressure of gas in the container, so increasing the buoyancy of the enclosed bulb. In one experiment, the balance point was reached when the fluorocarbon pressure was 327.10Torr; for the same setting of the pivot, a balance was reached when CHF3 (M = 70.014 g mol−1) was introduced at 423.22 Torr. A repeat of the experiment with a di erent setting of the pivot required a pressure of 293.22 Torr of the uorocarbon and 427.22 Torr of the CHF3. What is the molar mass of the fluorocarbon? Suggest a molecular formula.arrow_forward4.64. The gas-phase reaction between methanol and acetic acid to form methyl acetate and water CH;OH + CH3COOH = CH3COOCH3 + H2O (A) (В) (C) (D) takes place in a batch reactor. When the reaction mixture comes to equilibrium, the mole fractions of the four reactive species are related by the reaction eqilibrium constant Ky : = 4.87 YAYB (a) Suppose the feed to the reactor consists of n40,NB0, NCo, NDO, and no gram-moles of A, B, C, D, and an inert gas, I, respectively. Let į be the extent of reaction. Write expressions for the gram-moles of each reactive species in the final product, nA(2), nB(3), nc(E), and np(3). Then use these expressions and the given equilibrium constant to derive an equation for , the equilibrium extent of reaction, in terms of n20,.., N1o. (see Example 4.6-2.) (b) If the feed to the reactor contains equimolar quantities of methanol and acetic acid and no other species, calculate the equilibrium fractional conversion. (c) It is desired to produce 70 mol of methyl…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY