EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.26P
A stream of air at 35°C and a gauge pressure of 0.5 atm (Stream 1) flows into a pipe passing through a heater, emerges at 87°C and 0.2 atm (gauge), and splits into two streams. Stream 2 passes out of the system, and Stream 3 goes through another heater and emerges at 180°C and 0.1 atm (gauge). Flowmeters mounted in all three streams show readings of 3120 L/min (Stream 1), 1940 L/mm (Stream 2), and 3420 L/min (Stream 3).
(a) Show that the system is not functioning properly.
(b) Speculate on several possible causes of the malfunction, and state how you would check each one.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
6- Floor beams of a transport airplane have been designed using an aluminum alloy containing 4.5
wt% Cu and 1.5 wt% Mg for a total weight of 95000 N. A customer has ordered the airplane but
requested that its total weight be reduced by 10 percent for fuel saving purposes. An engineer in
the design and analysis department has suggested that the weight saving objective can be
accomplished by replacing the current aluminum alloy of the floor beams with another one
containing 3 wt% Li and 1 wt% Cu. Is this possible? Answer the question by first determining
the weight saving that will take place using the Al-Li alloy. Assume weighted averages of density
and use the following densities for the mentioned materials:
Al = 2.70 g/cm³
Cu = 8.92 g/cm³
Mg = 1.74 g/cm³
Li = 0.53 g/cm³
A brine solution of salt flows at a constant rate of 9 L/min into a large tank that initially held 100 L of brine solution in which was dissolved 0.4 kg of salt. The solution
inside the tank is kept well stirred and flows out of the tank at the same rate. If the concentration of salt in the brine entering the tank is 0.04 kg/L, determine the mass
of salt in the tank after t min. When will the concentration of salt in the tank reach 0.01 kg/L?
Determine the mass of salt in the tank after t min,
mass = | kg
Two aqueous sulfuric acid solutions
are available at a processing facility:
20.0 wt% H2SO4 (sg = 1.139)
60.0 wt% H2SO4 (sg = 1.498)
It is desired to mix the two solutions
such that the final product has a
concentration of 4.00 M (sg-1.213).
There is 100 kg of the 20% solution
available. If all of this is to be used,
calculate:
The mass of 60% solution needed
The mass and composition of the final
product
Chapter 5 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 5 - A liquid mixture containing 40.0 wt% n-octane and...Ch. 5 - Prob. 5.2PCh. 5 - Prob. 5.3PCh. 5 - Prob. 5.4PCh. 5 - Prob. 5.5PCh. 5 - Prob. 5.6PCh. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - Prob. 5.9PCh. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - Prob. 5.12PCh. 5 - Prob. 5.13PCh. 5 - Prob. 5.14PCh. 5 - Prob. 5.15PCh. 5 - Prob. 5.16PCh. 5 - Prob. 5.17PCh. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - A device has been designed to measure the flow...Ch. 5 - Prob. 5.21PCh. 5 - Prob. 5.22PCh. 5 - Spray drying is a process in which a liquid...Ch. 5 - Prob. 5.24PCh. 5 - Lewis12 describes the hazards of breathing air...Ch. 5 - A stream of air at 35°C and a gauge pressure of...Ch. 5 - Prob. 5.27PCh. 5 - In froth ?otation, air is bubbled through an...Ch. 5 - Prob. 5.29PCh. 5 - Prob. 5.30PCh. 5 - Bread is typically made by ?rst dissolving...Ch. 5 - Prob. 5.32PCh. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - A spray-drying operation similar to that described...Ch. 5 - Prob. 5.41PCh. 5 - Fermentation is a biochemical process in which a...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - Ethane at 25°C and 1.1 atm (abs) flowing at a rate...Ch. 5 - The ?ow of air to a gas-?red boiler furnace is...Ch. 5 - Prob. 5.47PCh. 5 - The oxidation of nitric oxide NO+12O2NO2 takes...Ch. 5 - Prob. 5.49PCh. 5 - 5.50.19 In chemical vapor deposition (CVD), a...Ch. 5 - A gas turbine power plant receives a shipment of...Ch. 5 - Prob. 5.52PCh. 5 - 5.53.20 Chemicals are stored in a laboratory with...Ch. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - A stream of ho dry nitrogen flows through a...Ch. 5 - Prob. 5.57PCh. 5 - You have purchased a gas cylinder that is supposed...Ch. 5 - The current global reliance on fossil fuels for...Ch. 5 - Two humid gas streams are combined in a heated...Ch. 5 - Most of the concrete used in the construction of...Ch. 5 - The ultimate analysis of a No. 4 fuel oil is 86.47...Ch. 5 - A stream of liquid n-pentane flows at a rate of...Ch. 5 - Alka-Seltzer( is an over-the-counter medicine used...Ch. 5 - Hydrogen sul?de has the distinctive unpleasant...Ch. 5 - The quantity of sulfuric acid used globally places...Ch. 5 - A small power plant produces 500 MW of electricity...Ch. 5 - You have been assigned the task of measuring the...Ch. 5 - Prob. 5.69PCh. 5 - Methanol is synthesized from carbon monoxide and...Ch. 5 - Prob. 5.71PCh. 5 - Prob. 5.72PCh. 5 - Steam reforming is an important technology for...Ch. 5 - A ?owchart of a methanol synthesis process is...Ch. 5 - The measured volumetric flow rate of ethane at...Ch. 5 - Prob. 5.76PCh. 5 - Methanol is to be delivered to a process unit at a...Ch. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - Prob. 5.82PCh. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - Prob. 5.85PCh. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - Prob. 5.89PCh. 5 - A fuel cell is an electrochemical device that...Ch. 5 - In a metered-dose inhaler (MDI), such as those...Ch. 5 - Prob. 5.92PCh. 5 - Prob. 5.93PCh. 5 - Approximately 150 SCFM (standard cubic feet per...Ch. 5 - Prob. 5.95PCh. 5 - Prob. 5.96PCh. 5 - Prob. 5.97PCh. 5 - The product gas from a coal gasification plant...Ch. 5 - Prob. 5.99PCh. 5 - Prob. 5.100PCh. 5 - A gas mixture consisting of 15.0 mole% methane....Ch. 5 - A system has been devised to store acetonitrile...Ch. 5 - Prob. 5.103PCh. 5 - Prob. 5.104P
Additional Science Textbook Solutions
Find more solutions based on key concepts
If it takes 11 minutes to cook spaghetti in Ann Arbor, Michigan, and 14 minutes in Boulder, Colorado, how long ...
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
UseLaplace transforms to find the solution to the following set of equations dy1dt+y2=xdy2dt+3y2=2y1 for x=et e...
Process Dynamics and Control, 4e
What is byte code?
Starting Out with Java: From Control Structures through Objects (7th Edition) (What's New in Computer Science)
The force for equilibrium in each cord.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Monthly Payments The monthly payment on a loan may be calculated by the following formula. Payment=Rate(1+Rate)...
Starting Out with C++ from Control Structures to Objects (8th Edition)
What is a default constructor? Is it possible to have more than one default constructor?
Starting Out with C++ from Control Structures to Objects (9th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- Biogas system design for cooking for a family of 9 members is considered here. The system design includes the estimation of total gas required, amount of feedstock (or dung), required and the number of animals required to have feedstock of a given amount. Following assumptions are made for the design: 1- About 350-450 liters of biogas required per day per person for cooking (in engine about 450 liters/hp/hour of biogas is required) 2- Average production of dung per animal per day: (Cow:10 kg/day, Bullock:14 kg/day and Buffalo:15 kg/day) 3- Other assumptions are: 1000 liters of gas is equivalent to 1 m3 of gas, average gas production from dung is about 40 liters/kg of fresh dung and retention period of dung slurry in digester is 50 days. Find 1- Bullocks 2- Buffalos 3:46 PM /arrow_forwardp/(kg m) 0.225 0.456 0.664 1.062 1.468 1.734 P1A.6 The molar mass of a newly synthesized fluorocarbon was measured in a gas microbalance. This device consists of a glass bulb forming one end of a beam, the whole surrounded by a closed container. The beam is pivoted, and the balance point is attained by raising the pressure of gas in the container, so increasing the buoyancy of the enclosed bulb. In one experiment, the balance point was reached when the fluorocarbon pressure was 327.10 Torr; for the same setting of the pivot, a balance was reached when CHF, (M= 70.014g mol) was introduced at 423.22 Torr. A repeat of the experiment with a different setting of the pivot required a pressure of 293.22 Torr of the fluorocarbon and 427.22 Torr of the CHF,. What is the molar mass of the fluorocarbon? Suggest a molecular formula. P1A.7 A constant-volume perfect gas thermometer indicates a pressure of 6.69 kPa at the triple point temperature of water (273.16 K). (a) What chang of pressure…arrow_forward+ M Inbox (2,372) - ftantill@ude x ← < app.101edu.co STARTING AMOUNT 56°F Rain off and on X 22F-CHEM103-510: Generax 36 H ▬▬▬▬ 4 Aktiv Chemistry 0.98692 ADD FACTOR x( ) A tire pressure gauge reads 33.0 pounds per square inch How many kPa is this? Remember that multiple steps may be required in the conversion. atm O Search 2.27 227 X Pa 0.00222 101.325 Convert 33 psi to kpa | Qui x Question 15 of 41 psi 14.70 1000 ANSWER 0.001 760 1.01325 1.01325 x 10 mm Hg CHEM103-Lecture Notes X kPa bar 0 ✓ PrtScn RESET 2 10⁰ 33.0 torr Home 1 Enthalpy of Formation Reax hula End FD + PgUp გა 3 PgOn D Update X Submit + 6:54 PM D 12/6/2022 te er FLarrow_forward
- 2-4. Gasoline vapors are vented to the atmosphere when an underground gasoline storage tank is filled. If the tanker truck discharges into the top of the tank with no vapor control (known as the splash fill method), the emission of gaso- line vapors is estimated to be 2.75 kg/m' of gasoline delivered to the tank. If the tank is equipped with a pressure relief valve and interlocking hose connec- tion and the tanker truck discharges into the bottom of the tank below the surface of the gasoline in the storage tank, the emission of gasoline vapors is estimated to be 0.095 kg/m of gasoline delivered (Wark et al., 1998). Assume that the service station must refill the tank with 4.00 m' of gasoline once a week. Draw a mass balance diagram and estimate the annual loss of gasoline vapor (in kg/y) for the splash fill method. Estimate the value of the fuel that is captured if the vapor control system is used. Assume the density of the con- densed vapors is 0.800 g/mL and the cost of the gasoline…arrow_forwardUse yourresearch skill to find out the size onethree cylindrical tank, on Petrojam tankfarm. Find out the petroleum products used, and describe the present way of measuring volume and mass, from their main office (distance). Describe an automated wayto measurethe petroleum product at the main office and used Telemetry (SCADA)to verify measurement from your home of onethe petroleum product mass and volume. The Project may include things such as DP-cell, Ultrasonicsensor, fieldbus Module, and Calibration.arrow_forwardA wet gas is produced through a two-stage separator system. Separator conditions are 580 psia and 95°F. The stock tank is at 80°F. Gas-oil ratios for separator and stock tank are 98835 scf/STB and 408 scf/STB. The stock-tank liquid has a gravity of 59.3°API. The compositions of the surface production are given in the table below. (a) Calculate the composition of the reservoir gas. (b) Calculate wet gas formation volume factor at reservoir conditions of 2250 psig and 200 °F. (c) Calculate wet gas isothermal compressibility factor at reservoir conditions of 2250 psig and 200 °F. Composition, Separator Gas, Mole fraction Composition, Stock-tank Liquid, Component Composition, Stock-tank Gas, Mole fraction Mole fraction 0.8814 0.4795 0.0026 C2 0.0730 0.1769 0.0054 0.1755 0.0194 C3 i-C4 n-C4 0.0297 0.0054 0.0490 0.0148 0.0045 0.0023 0.0466 0.0193 i-Cs n-Cs 0.0293 0.0312 0.0017 0.0222 0.0293 C6 0.0016 0.0190 0.0902 C7+ 0.0004 0.0020 0.7878 Properties of heptanes plus of the stock-tank liquid:…arrow_forward
- A tire pressure gauge reads 33.0 pounds per square inch . How many kPa is this? Remember that multiple steps may be required in the conversion. STARTING AMOUNT ADD FACTOR ANSWER RESET 0.001 33.0 0.98692 1 10 0.00222 1.01325 760 1.01325 x 10 14.70 101.325 227 2.27 1000 psi bar Pa mm Hg atm tor kPa MacBook Air 20 24 2 3 41 5 6 RI Darrow_forward3-9. A 40-cu ft tank is filled with air at 14.7 psia and 80°F. The tank also contains a 15-lb block of dry ice (solid CO2, specific gravity of 1.53 based on water). After the dry ice sublimes, the temperature is 30°F. What is the pressure? Assume ideal gas behavior.arrow_forwardH2. Cartons of product are accumulated on the floor adjacent to a conveyor. The job consists of a worker lifting the cartons from the floor and placing them on the conveyor. The height of the conveyor is 61 cm. The cartons are 30 cm height, 30 cm width, and 40 cm length . The horizontal distance from the worker’s ankles to the center of the carton is 20 cm. Carton weight is 9 kg. Frequency of lift is 2 lifts per minute and the duration of the task is between 1 and 2 hours. The cartons have a fair handholds. Control at the destination of lift is not required. The angle of asymmetry at the origin of lift may be taken to be 45 degrees. Use the NIOSH equation to calculate the Recommended Weight Limit (RWL) and the Lifting Index (LI). Comment on the safety of this lifting task.arrow_forward
- 2.5. The off-gases from a gasoline stabilizer are fed to a steam reforming plant to produce hydrogen. The composition of the off-gas, molar%, is: CH4 77.5, C2H6 9.5, C3Hg 8.5, C4H10'4.5. The gases entering the reformer are at a pressure of 2 bara and 35 °C and the feed rate is 2000 m/h. The reactions in the reformer are 1. CH2, +2 + n(H,O) → n(CO) + (2, + 1)H2 2. CO + H2O -→ CO2 + H2 The molar conversion of C,H2u+2 in reaction (1) is 96% and of CO in reaction (2) is 92%. Calculate a. the average molecular mass of the off-gas, b. the mass of gas fed to the reformer, kg/h, c. the mass of hydrogen produced, kg/h.arrow_forward(5) The emissions from a manufacturing process contain gaseous pollutant that cause odors and fumes. The company plans to incinerate the 5,000 acfm exhaust stream. Estimate the volumetric (standard) flowrate of natural gas fuel required to increase the waste gas stream temperature from the initial 80°F to the required temperature of 2500°F. Energy (enthalpy) is transferred from the fuel to the gas. Neglect any possible heat losses in this process. The average net heating value of natural gas is 850 - 1050 Btu/std-ft. Include a diagram of the scenario.arrow_forwardThe data below was collected using the procedure described in your lab notebook: Mass (before reaction): test tube + HCl(aq) + stir bar + capsule 27.000 g Mass (after reaction): test tube + HCl(aq) + stir bar + capsule 25.000 g Volume of water displaced from the squirt bottle 146 mL Temperature of the CO2(g) 298.5 K Pressure (atm) 1.012 atm Using this data answer each of the questions below. Enter your answer to three significant figures and enter only the numerical value in the answer box. Calculate the mass of CO2(g). Calculate the number of moles of CO2(g). Calculate the density of CO2(g) in g/L. Calculate the molar mass of CO2 assuming a temperature of 298.5 K. Calculate the Gas constant, R, in L*atm/K*mol. Calculate the % error of the value of the Gas constant, R.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY
Introduction to Nonreactive Processes Without Phase Change; Author: NPTEL-NOC IITM;https://www.youtube.com/watch?v=1Okp7895M6I;License: Standard YouTube License, CC-BY