EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.62P
The ultimate analysis of a No. 4 fuel oil is 86.47 wt% carbon. 11.65% hydrogen, 1.35 sulfur, and the balance noncombustible inerts. This oil is burned in a steam-generating furnace with 15% excess air. The air is preheated to 175°C and enters the furnace at a gauge pressure of 180 mm Hg. The sulfur and hydrogen in the fuel are completely oxidized to SO2 and H2O; 5% of the carbon is oxidized to CO, and the balance forms CO2.
(a) Calculate the feed ratio (m3 air)/(kg oil).
(b) Calculate the mole fractions (dry basis) and ppm (parts per million on a wet basis, or moles contained in 106 moles of the wet stack gas) of the stack-gas species that might be considered environmental hazards.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In a chemical production plant, cyclohexane is made by the reaction of benzene and hydrogen. Reaction is as follows:
CHs + H2 → CoH12
The complete process of producing cyclohexane uses a reactor and a separator. Using the process shown below
and assuming 20 % excess hydrogen in the fresh feed, find the ratio of the recycle stream to the fresh feed
stream, the composition of the final product stream, and the composition of the stream leaving the reactor. The
overall conversion of benzene is 92% and the single-pass conversion is 21.5 %. The recycle stream is composed
of 23.9 % benzene and the remaining hydrogen.
Fresh
Feed
REACTOR
SEPARATOR
Product
Recycle
6- Floor beams of a transport airplane have been designed using an aluminum alloy containing 4.5
wt% Cu and 1.5 wt% Mg for a total weight of 95000 N. A customer has ordered the airplane but
requested that its total weight be reduced by 10 percent for fuel saving purposes. An engineer in
the design and analysis department has suggested that the weight saving objective can be
accomplished by replacing the current aluminum alloy of the floor beams with another one
containing 3 wt% Li and 1 wt% Cu. Is this possible? Answer the question by first determining
the weight saving that will take place using the Al-Li alloy. Assume weighted averages of density
and use the following densities for the mentioned materials:
Al = 2.70 g/cm³
Cu = 8.92 g/cm³
Mg = 1.74 g/cm³
Li = 0.53 g/cm³
The boiler in an apartment building uses propane (C3H8) to heat
water that circulates throughout the building as steam. 1.00
m'/s of propane gas at 25°C and 1 atm is combusted with 10%
excess air at 25°C and 1 atm. After all of the propane is
combusted, the product gas contains a 10.0:1 molar ratio of
CO2 to CO and leaves the boiler at 25°C. Heat from the boiler
is transferred to a pure water stream at 50°C and 1.0 bar, which
is converted into saturated steam at 20 bar, with no heat lost to
the surroundings in the process. What mass of water is heated
in this process?
Molecule
(Formula)
(kJ/mol)
-393.5 (g)
Carbon
dioxide
(CO2)
Carbon
-110.52 (g)
monoxide
(CO)
Hydrogen
(H2)
Nitrogen
(N2)
Охуgen
(O2)
Propane
(C;Hs)
Hot Water (out).
Flue
Gas Shutoff Valve -
Cold Water (in)
-119.8(1)
-103.8(g)
-285.84(1)
Gas Supply Line-
Cold Water
Shutoff Valve
Water
(H20)
-241.83(g)
Temperature /
Pressure Relief
Valve
Water Line
Overflow Pipe.
Tank Insulation
- Dip Tube
Drain Valve
Gas Burner Control-…
Chapter 5 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 5 - A liquid mixture containing 40.0 wt% n-octane and...Ch. 5 - Prob. 5.2PCh. 5 - Prob. 5.3PCh. 5 - Prob. 5.4PCh. 5 - Prob. 5.5PCh. 5 - Prob. 5.6PCh. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - Prob. 5.9PCh. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - Prob. 5.12PCh. 5 - Prob. 5.13PCh. 5 - Prob. 5.14PCh. 5 - Prob. 5.15PCh. 5 - Prob. 5.16PCh. 5 - Prob. 5.17PCh. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - A device has been designed to measure the flow...Ch. 5 - Prob. 5.21PCh. 5 - Prob. 5.22PCh. 5 - Spray drying is a process in which a liquid...Ch. 5 - Prob. 5.24PCh. 5 - Lewis12 describes the hazards of breathing air...Ch. 5 - A stream of air at 35°C and a gauge pressure of...Ch. 5 - Prob. 5.27PCh. 5 - In froth ?otation, air is bubbled through an...Ch. 5 - Prob. 5.29PCh. 5 - Prob. 5.30PCh. 5 - Bread is typically made by ?rst dissolving...Ch. 5 - Prob. 5.32PCh. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - A spray-drying operation similar to that described...Ch. 5 - Prob. 5.41PCh. 5 - Fermentation is a biochemical process in which a...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - Ethane at 25°C and 1.1 atm (abs) flowing at a rate...Ch. 5 - The ?ow of air to a gas-?red boiler furnace is...Ch. 5 - Prob. 5.47PCh. 5 - The oxidation of nitric oxide NO+12O2NO2 takes...Ch. 5 - Prob. 5.49PCh. 5 - 5.50.19 In chemical vapor deposition (CVD), a...Ch. 5 - A gas turbine power plant receives a shipment of...Ch. 5 - Prob. 5.52PCh. 5 - 5.53.20 Chemicals are stored in a laboratory with...Ch. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - A stream of ho dry nitrogen flows through a...Ch. 5 - Prob. 5.57PCh. 5 - You have purchased a gas cylinder that is supposed...Ch. 5 - The current global reliance on fossil fuels for...Ch. 5 - Two humid gas streams are combined in a heated...Ch. 5 - Most of the concrete used in the construction of...Ch. 5 - The ultimate analysis of a No. 4 fuel oil is 86.47...Ch. 5 - A stream of liquid n-pentane flows at a rate of...Ch. 5 - Alka-Seltzer( is an over-the-counter medicine used...Ch. 5 - Hydrogen sul?de has the distinctive unpleasant...Ch. 5 - The quantity of sulfuric acid used globally places...Ch. 5 - A small power plant produces 500 MW of electricity...Ch. 5 - You have been assigned the task of measuring the...Ch. 5 - Prob. 5.69PCh. 5 - Methanol is synthesized from carbon monoxide and...Ch. 5 - Prob. 5.71PCh. 5 - Prob. 5.72PCh. 5 - Steam reforming is an important technology for...Ch. 5 - A ?owchart of a methanol synthesis process is...Ch. 5 - The measured volumetric flow rate of ethane at...Ch. 5 - Prob. 5.76PCh. 5 - Methanol is to be delivered to a process unit at a...Ch. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - Prob. 5.82PCh. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - Prob. 5.85PCh. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - Prob. 5.89PCh. 5 - A fuel cell is an electrochemical device that...Ch. 5 - In a metered-dose inhaler (MDI), such as those...Ch. 5 - Prob. 5.92PCh. 5 - Prob. 5.93PCh. 5 - Approximately 150 SCFM (standard cubic feet per...Ch. 5 - Prob. 5.95PCh. 5 - Prob. 5.96PCh. 5 - Prob. 5.97PCh. 5 - The product gas from a coal gasification plant...Ch. 5 - Prob. 5.99PCh. 5 - Prob. 5.100PCh. 5 - A gas mixture consisting of 15.0 mole% methane....Ch. 5 - A system has been devised to store acetonitrile...Ch. 5 - Prob. 5.103PCh. 5 - Prob. 5.104P
Additional Science Textbook Solutions
Find more solutions based on key concepts
Inspector Sgt. Ambercromby of Scotland Yard. It is believed, although never proven, that Bonnie murdered her fi...
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
For the integro-differential equation, d2xdt2+4dxdt+3x=20ftedwithdxdt(0)=x(0)=0. a. Find x(t) b. What is the li...
Process Dynamics and Control, 4e
Describe the friction welding process.
Degarmo's Materials And Processes In Manufacturing
Determine the capacitor voltage, power, and stored energy at t = 20 ms in the circuit ofFigure P3.12 Figure P3....
Electrical Engineering: Principles & Applications (7th Edition)
Write a while loop that asks the user to enter two numbers. The numbers should be added and the sum displayed. ...
Starting Out with Python (4th Edition)
Find Io in the circuit in Fig. P5.21 using superposition.
Basic Engineering Circuit Analysis
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- A gaseous fuel containing methane and ethane is burned with excess air. The fuel enters the furnace at 25°C and 1 atm, and the air enters at 200°C and 1 atm. The stack gas leaves the furnace at 800°C and 1 atm and contains 5.32 mole% CO2, 1.60% CO, 7.32% O₂, 12.24% H₂O, and the balance ₂. 1. Calculate the molar percentages of methane and ethane in the fuel gas and the percentage excess air fed to the reactor. 2. Calculate the heat (kJ) transferred from the reactor per cubic meter of fuel gas fed. 3. A proposal has been made to lower the feed rate of air to the furnace. State advantages and a drawback of doing so.arrow_forwardAn underfeed stoker feeds coal to a boiler at the rate of 100 kg/hr. The ultimate analysis of coal is: C = 75.2 %, H;= 3.6 %, O2 = 7.4 %, N2 = 1.2 %, S = 2.1 % and the remaining is Ash. The dry refuse taken from the ash pit shows 20 % C and 80 % ash by weight. Orsat analysis of the flue gases gives the following composition, CO2 = 75.2 %, O, = 7.9 %, CO= 1 % Determine: a) m³ of air supplied per minute if the pressure is 100 kPaa and 20 °C; b) Total volume of flue gases flowing through the stack per minute if the temperature is 60 °C and pressure is 100 kPaa.arrow_forwardFeed gas containing of 78.5mol % H₂, 21% of N₂ & 0.5% of Ar is mixed with recycle gas and enters a reactor where 15% N₂ is converted to NH3 as per the reaction. Ammonia from the exit of the reactor is completely separated from unconverted gases. To avoid the buildup of inerts, a small fraction (5%) of the unreacted gases purged and the balance recycled. USING ASPEN/HYSYS Draw the process flow sheet Product rate and Purge rate Basis:100mol/hrarrow_forward
- Producer gas is a fuel that is manufactured from the reaction of coal, steam and air. A producer gas has the following composition by volume (dry basis): 20.35% CO, 11.03%, CO2, 15% H2, 51.43% N2, 1.98%O2 and 0.21 % CH4. The gas is flowing at 6000 cfm. It has a temperature of 200℃ , a pressure of 21 cm Hg and a partial pressure of 50 mm Hg for H2O. The atmospheric pressure is 758 mm Hg. The gas is delivered from the source to the furnace by means of a pipe. It cools down to 50 ℃ and is compressed to 2 atm pressure. At this condition, calculate:1. the volumetric flow ate2. the mass flow rate3. the partial pressure of each component/including water)4. complete analysis of the mixturearrow_forwardTwo-hundred fifty pounds per hour of iron pyrites containing 90% FeS2 and 10% gangue are burned with 20% excess air based on conversion to SO3. The cinder discharged from the burner contains no sulfur. No conversion to SO3 occurs in the burner. The burner gas is passed through a converter which effects a 98% conversion of SO2 to SO3. The converter gas is passed to an absorber where all the SO3 is absorbed by 80% H2SO4 solution, which becomes 100% H2SO4 solution in the process. Establish a basis of one hundred pounds of iron pyrites Calculate: (a) the burner gas analysis, (b) the converter gas analysis, (c) pounds of 100% H2SO4 produced per 24-h day, if waste gas analyzes 0.19% SO2, 4.14% O2 and 95.67% N2arrow_forward1. Fresh air containing 4.00 mole % water vapor is to be cooled and dehumidified to a water content of 1.70 mole% H20. A stream of fresh air is combined with a recycle stream of previously dehumidified air and passed through the cooler. The blended stream entering the unit contains 2.30 mole% H2O. In the air conditioner, some of the water in the feed stream is condensed and removed as liquid. A fraction of the humidified air delivered to the cooler is recycled and the remainder is delivered to a room. Taking 100 mole of dehumidified air delivered to the room as a basis of calculation; calculate the moles of fresh feed, moles of water condensed, and moles of dehumidified air recycled. Recycle stream (R) Fresh air (F) Dehumidifier → 100 moles Water removed (Y)arrow_forward
- A mixture containing 42 wt% benzene (B) and 58 wt% toluene (T) is fed to a distillation column at a flow rate of 100 kg per minute. The product steam leaving the top of the column (the overhead product) contains 90 wt% benzene and 85 wt% of the total benzene fed to the column exits in this overhead product stream. Calculate the mass flow rate and mass composition of the product stream leaving the bottom of the column. Calculate the volumetric flow rate of the overhead product, assuming that it exits the distillation column as a vapour stream at 82C and 1 atm (abs). Physical Property Data (S.G.= specific gravity) from table B-1: Benzene S.G. = 0.879 MW = 78.11 g/mol Toluene S.G. = 0.866 MW = 92.13 g/mol Water Density = 1.00 kg/L MW = 18.02 g/mol R = 0.08206 L atm/mol Karrow_forward2. In an ethanol production plant, a separator produces a 99% ethanol product from a feedstock stream containing 85% water and 15% ethanol at a rate of 450 Ib/min. The separator has two outlet streams: the ethanol product outlet stream (99% ethanol) and a residual water stream. 30% of the feedstock is bypassed and mixed with the residual water stream leaving the separator. If 60% of the ethanol entering the separator is recovered in the product stream, determine the composition of the residual water stream just after leaving the separator and the composition of the residual stream after mixing with the bypass stream.arrow_forwardNaturally occurring barium sulphate is converted into water–soluble formby heating with carbon, thus reducing the sulphate to barium sulphide(BaS). The resulting reaction mixture, “barium black ash”, contains 65%w/w soluble BaS and is to be leached with water. Black ash is to be fedto a tube mill at 100 tonnes per day, together with the overflow from thesecond of a cascade of thickeners, and the effluent from the mill is fed tothe first thickener. All the barium is dissolved in the mill. The strongsolution leaving the first thickener contains 20% w/w BaS by weight.Each thickener delivers a sludge with 1.5 kg liquid per kg of insolublesolid. Both liquids leaving each thickener are to have the same BaSconcentration. BaS lost with the final sludge should not exceed 1 kg perday.How many thickeners are needed?arrow_forward
- (5) The emissions from a manufacturing process contain gaseous pollutant that cause odors and fumes. The company plans to incinerate the 5,000 acfm exhaust stream. Estimate the volumetric (standard) flowrate of natural gas fuel required to increase the waste gas stream temperature from the initial 80°F to the required temperature of 2500°F. Energy (enthalpy) is transferred from the fuel to the gas. Neglect any possible heat losses in this process. The average net heating value of natural gas is 850 - 1050 Btu/std-ft. Include a diagram of the scenario.arrow_forwardThe synthesis of methanol from carbon monoxide and hydrogen is carried out in a continuous vapor-phase reactor at 5.00 atm absolute. The feed contains cO and H2 in stoichiometric proportion and enters the reactor at 25.0°C and 5.00 atm at a rate of 31.1 m³/h. The product stream emerges from the reactor at 157°C. The rate of heat transfer from the reactor is 21.0 kW. Calculate the fractional conversion (0 to 1) of carbon monoxide achieved and the volumetric flow rate (m3/h) of the product stream. f = Vout ! m3/harrow_forwardA steady-state process to recover crystalline potassium chromate (K,CrOz) from an aqueous solution of this salt is required. Four thousand kilograms per hour of a solution that is one-third K,CrO, by mass is joined by a recycle stream containing 36.4% K2CrO7, and the combined stream is fed into an evaporator. The concentrated stream leaving the evaporator contains 49.4% K,CrO; this stream is fed into a crystallizer in which it is cooled (causing crystals of K,CrO, to come out of solution) and then filtered. The filter cake consists of K,CrO, crystals and a solution that contains 36.4% K,CrO, by mass; the crystals account for 95% of the total mass of the filter cake. The solution that passes through the filter, also 36.4% K,CrO,, is the recycle stream. 1- Draw the flowchart of the system and put all known information. 2- Calculate the rate of evaporation, the rate of production of crystalline K,CrO7, the feed rates that the evaporator and the crystallizer must be designed to handle, and…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY
Mod-01 Lec-23 Degrees of freedom analysis; Author: nptelhrd;https://www.youtube.com/watch?v=c4h85JjrkzQ;License: Standard YouTube License, CC-BY
Introduction to Degrees of Freedom; Author: LearnChemE;https://www.youtube.com/watch?v=tW1ft4y5fQY;License: Standard Youtube License