EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 5, Problem 5.89P
Interpretation Introduction
(a)
Interpretation:
The original mass of oxygen in the tank is to be calculated.
Concept introduction:
The extent of deviation of the real gases from the ideal gases can be studied by a factor known as compressibility factor. The formula for the compressibility factor (z) is-
Where,
- P is the pressure
- V is the volume of the container
- n is the number of moles
- R is gas constant
- T is the temperature
Interpretation Introduction
(b)
Interpretation:
The initial pressure of the gas at temperature
Concept introduction:
The extent of deviation of the real gases from the ideal gases can be studied by a factor known as compressibility factor.The formula for the compressibility factor (z) is-
Where,
- P is the pressure
- V is the volume of the container
- n is the number of moles
- R is gas constant
- T is the temperature
Interpretation Introduction
(c)
Interpretation:
The time taken by the gauge on the tank to read 50 psig on an average flow rate of
Concept introduction:
The extent of deviation of the real gases from the ideal gases can be studied by a factor known as compressibility factor. The formula for the compressibility factor (z) is-
Where,
- P is the pressure
- V is the volume of the container
- n is the number of moles
- R is gas constant
- T is the temperature
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
P1A.6 The molar mass of a newly synthesized fluorocarbon was measured in a gas microbalance. is device consists of a glass bulb forming one end of a beam, the whole surrounded by a closed container. e beam is pivoted, and the balance point is attained by raising the pressure of gas
in the container, so increasing the buoyancy of the enclosed bulb. In one experiment, the balance point was reached when the fluorocarbon pressure was 327.10Torr; for the same setting of the pivot, a balance was reached when CHF3 (M = 70.014 g mol−1) was introduced at 423.22 Torr. A repeat of the experiment with a di erent setting of the pivot required a pressure of 293.22 Torr of the uorocarbon and 427.22 Torr of the CHF3. What is the molar mass of the fluorocarbon? Suggest a molecular formula.
+ |/
00
%24
D.
Two bulbs are connected by a stopcock. The 7.50 L bulb contains nitric
oxide (NO) at a pressure of 0.340 bar, and the 2.50 L bulb contains
oxygen (O,) at a pressure of 0.510 bar.
02
ON
After the stopcock is opened, the gases mix and react to produce nitrogen dioxide
(CON)
2 NO(g) + 0,(g) – 2 NO,(g)
Considering that the volume remains unchanged during the experiment, how does the total pressure in the bulbs change if
the reaction is allowed to go to completion?
The total pressure will remain constant.
O There is not enough information to determine how the total pressure will change.
O The total pressure will decrease.
O The total pressure will increase.
MacBook Pro
(
The
%23
%24
7.
4.
5.
3.
R
%3D
K.
H.
B
C.
option
command
MOSISO
A 6.21 g mixture of sucrose (C₆H₁₂O₆, 342.30 g mol⁻¹) and ethyl alcohol (C₂H₆O, 46.07 g mol⁻¹) is reacted with acidic aqueous potassium dichromate (K₂Cr₂O₇) solution. Produced 5.12 L CO₂(g) is collected over water at 35 °C and has a barometric pressure of 0.95 atm. Water has a vapor pressure of 42.20 mmHg. Calculate the mass percent of C₆H₁₂O₆ in the mixture.
C₆H₁₂O₆(aq) + Cr₂O₇²⁻(aq) → CO₂(g) + Cr³⁺(aq)
(not balanced)
C₂H₆O(aq) + Cr₂O₇²⁻(aq) → CO₂(g) + Cr³⁺(aq)
(not balanced)
Chapter 5 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 5 - A liquid mixture containing 40.0 wt% n-octane and...Ch. 5 - Prob. 5.2PCh. 5 - Prob. 5.3PCh. 5 - Prob. 5.4PCh. 5 - Prob. 5.5PCh. 5 - Prob. 5.6PCh. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - Prob. 5.9PCh. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - Prob. 5.12PCh. 5 - Prob. 5.13PCh. 5 - Prob. 5.14PCh. 5 - Prob. 5.15PCh. 5 - Prob. 5.16PCh. 5 - Prob. 5.17PCh. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - A device has been designed to measure the flow...Ch. 5 - Prob. 5.21PCh. 5 - Prob. 5.22PCh. 5 - Spray drying is a process in which a liquid...Ch. 5 - Prob. 5.24PCh. 5 - Lewis12 describes the hazards of breathing air...Ch. 5 - A stream of air at 35°C and a gauge pressure of...Ch. 5 - Prob. 5.27PCh. 5 - In froth ?otation, air is bubbled through an...Ch. 5 - Prob. 5.29PCh. 5 - Prob. 5.30PCh. 5 - Bread is typically made by ?rst dissolving...Ch. 5 - Prob. 5.32PCh. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - A spray-drying operation similar to that described...Ch. 5 - Prob. 5.41PCh. 5 - Fermentation is a biochemical process in which a...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - Ethane at 25°C and 1.1 atm (abs) flowing at a rate...Ch. 5 - The ?ow of air to a gas-?red boiler furnace is...Ch. 5 - Prob. 5.47PCh. 5 - The oxidation of nitric oxide NO+12O2NO2 takes...Ch. 5 - Prob. 5.49PCh. 5 - 5.50.19 In chemical vapor deposition (CVD), a...Ch. 5 - A gas turbine power plant receives a shipment of...Ch. 5 - Prob. 5.52PCh. 5 - 5.53.20 Chemicals are stored in a laboratory with...Ch. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - A stream of ho dry nitrogen flows through a...Ch. 5 - Prob. 5.57PCh. 5 - You have purchased a gas cylinder that is supposed...Ch. 5 - The current global reliance on fossil fuels for...Ch. 5 - Two humid gas streams are combined in a heated...Ch. 5 - Most of the concrete used in the construction of...Ch. 5 - The ultimate analysis of a No. 4 fuel oil is 86.47...Ch. 5 - A stream of liquid n-pentane flows at a rate of...Ch. 5 - Alka-Seltzer( is an over-the-counter medicine used...Ch. 5 - Hydrogen sul?de has the distinctive unpleasant...Ch. 5 - The quantity of sulfuric acid used globally places...Ch. 5 - A small power plant produces 500 MW of electricity...Ch. 5 - You have been assigned the task of measuring the...Ch. 5 - Prob. 5.69PCh. 5 - Methanol is synthesized from carbon monoxide and...Ch. 5 - Prob. 5.71PCh. 5 - Prob. 5.72PCh. 5 - Steam reforming is an important technology for...Ch. 5 - A ?owchart of a methanol synthesis process is...Ch. 5 - The measured volumetric flow rate of ethane at...Ch. 5 - Prob. 5.76PCh. 5 - Methanol is to be delivered to a process unit at a...Ch. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - Prob. 5.82PCh. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - Prob. 5.85PCh. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - Prob. 5.89PCh. 5 - A fuel cell is an electrochemical device that...Ch. 5 - In a metered-dose inhaler (MDI), such as those...Ch. 5 - Prob. 5.92PCh. 5 - Prob. 5.93PCh. 5 - Approximately 150 SCFM (standard cubic feet per...Ch. 5 - Prob. 5.95PCh. 5 - Prob. 5.96PCh. 5 - Prob. 5.97PCh. 5 - The product gas from a coal gasification plant...Ch. 5 - Prob. 5.99PCh. 5 - Prob. 5.100PCh. 5 - A gas mixture consisting of 15.0 mole% methane....Ch. 5 - A system has been devised to store acetonitrile...Ch. 5 - Prob. 5.103PCh. 5 - Prob. 5.104P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- A mixture of 80% CO2, and 20% CH4, (mass basis) is maintained at 310 K. 85 bar at which the specific volume has been measured as 0.00675 m^3 /kg. Calculate the percent deviation if the specific volume had been calculated by: a) Kay's rule; b) Compressibility factors and Amagat's law; c) What are the tables and charts you used for calculations? Assume the mixture's gas constant: Rm =mfi* Riarrow_forwardA 20-cu ft tank at 100 degrees F is pressured to 200 psia with a pure paraffin gas. Ten pounds of ethane are added, and the specific gravity of the gas mixture is measured to be 1.68. Assume that the gases act as ideal gases. What was the gas originally in the tank?arrow_forward1. The lung capacity of a scuba diver at the surface of the water is 3200 mL at 17°C and standard pressure. The diver goes to a depth where the pressure is 202 kPa and the temperature is 7°C. Calculate the volume of air that his lungs could hold at that depth.arrow_forward
- You are working in an oil refinery. Where you use hydrocarbon gases like methane (CH4), ethane (C2H), and propane (C3H8) and prepared a mixture, When measured the pressure at 25°C it turns out to be 7.50 atm. This gas mixture was then also used in a mass spectrophotometer and the following data was obtained. Based on this information find the partial pressure of each gas and report respectively as their name appeared in the question 10 30 40 50 Molecular maaNs (amu) اخترأحد الخبارات a. 2.3 atm, 3.8 atm, 1.4 atmO b. 4.0 atm, 1.5 atm, 2.5 atm O 2.1 atm, 4.0 atm, 1.4 atm O d. 3.8 atm, 1.4 atm, 23 atm e. 1.4 atm, 2.3 atm, 3.8 atmO Intensity of peaksarrow_forwardA steel cylinder containing compressed air is stored in a fermentation laboratory ready to provide aeration gas to a small-scale bioreactor. The capacity of the cylinder is 48 litres, the absolute pressure is 0.35 MPa and the temperature is 22°C. One day in mid-summer when the air conditioning breaks down, the temperature in the laboratory rises to 33°C and the valve at the top of the cylinder is accidentally left open. Estimate the proportion of air that will be lost. What assumptions will you make? 2 24 C.arrow_forward3120 Q4// A-Aclosed container of volume 0.02m contains a mixture of neon and argon at tempreture 27°c and pressure 1*10°NM². The total mass of mixture is 28gm. Give masses of indivisual gases in the container ,assuming them to be ideal D W..arrow_forward
- Pressure (A) Explain the term pressure and state its S.I. unit. (B) Explain Henry’s law. (C)A bottle of H2 has just been received by the technicians in DkIT for use in the instrumentation lab. It is a 47 litre cylinder at a pressure of 50 atmospheres. The normal working pressures is 2 bar. (i) To what volume of gas will that equate at the working pressure? (ii) For how many hours will the gas last if it used at the rate of 0.5dm3 per hour? D)You see your best friend at the bar and you walk up behind her. You accidentally startle her and she takes a step backwards. Unfortunately, she is wearing high heels and her heels come down on your foot. She weighs only 55kg but the size of her heel is 6mm by 6mm.Determine the pressure that she applies on your foot. (E) If a diver dives to a depth of 35 m what will be: (i) the pressure in Pascals due the water column? (3 marks) (ii) the pressure of the air in…arrow_forwardA steel cylinder containing compressed air is stored in a fermentation laboratory ready to provide aeration gas to a small-scale bioreactor. The capacity of the cylinder is 48 liters, the absolute pressure is 0.35 MPa and the temperature is 22°C. One day in mid-summer when the air conditioning breaks down, the temperature in the laboratory rises to 33°C and the valve at the top of the cylinder is accidentally left open. Estimate the proportion of air that will be lost.arrow_forwardThe ideal gas law relates the pressure P, volume V, absolute temperature T (Kelvin), and amount of gas n. nRT where R is the gas constant. P = The law is An engineer must design a large natural gas storage tank to be expandable to maintain the pressure constant at 2.2 atmospheres. In December when the temperature is -15°C, the volume of gas in the tank is 28,500 ft. What will the volume of the same quantity of gas be in July when the temperature is 31°C? (Hint: Use the fact that n, R, and P are constant in this problem. Note also that Kelvin = °C +273.2)arrow_forward
- At 0°C and under a pressure of 1.013 x 10ʻ kPa, the compressibility factor of O2 is 0.927. Calculate the weight of O2 needed to fill a gas cylinder with a volume of 100 dm’ under the given conditions. [1.54 x 10ʻ] Calculate the pressure exerted by 1.00 mol of C2H6 at 1000 K in 100 cm', using (a) the ideal gas equation, and (b) the van der Waals equation. The van der Waals constants for CH, are: a = 5.562 bar dm mol2; b= 0.06380 dm³ mol'. [831; 1.72 x 10*]arrow_forwardMetabolic engineering Consider the engineering design of microbial cell culture and growth in the field of biotech- nology and metabolic engineering. Bioreactors are employed incorporating the use of bio- chemical substrates that provide essential chemical elements for the growth of the microor- ganisms. A typical stoichiometric representation of the aerobic growth of a microorganism with a defined chemical formula is shown below C,H,OH + a0, b NH, - cCH, No.15004 + dH,0 + eCO, 3.5 (C-source) (O-source) (N-source) (Microorganism) The ratio of moles of CO2 produced per mole of O2 consumed is called the respiratory quotient, RQ, which can be experimentally determined, and is therefore treated as a known quantity. To determine the theoretical yield of production (growth) of the microorganism, the stoichiometric coefficients, a, b, c, d are required. One can easily formulate an elemental mass balance for each of the four key elements. (a) Formulate an elemental mass balance for each of the…arrow_forwardA gas mixture composed of 40 %wt methane, 28 %wt ethane, and 32 %wt propane is placed in a 16-liter vessel. Determine the partial pressure of each gas at 82 °F.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY