The Science and Engineering of Materials (MindTap Course List)
7th Edition
ISBN: 9781305076761
Author: Donald R. Askeland, Wendelin J. Wright
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 5.79P
What are the advantages of using hot pressing and hot isostatic pressing compared to using normal sintering?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What are the factors that affect on the
sintering process
A thin steel disk of an oil separator of 100mm outside diameter is shrunk onto a solid steel shaft
of 20mm diameter. The system is to be designed to make sure the disc does not become loose
at speeds lower than 100000rev/min. Determine the shrinkage allowance required in order to
avoid separation disc and shaft, at a speed of 100000rev/min.
For the material assume a Young's Modulus, Poisson Ratio and density of 210GPa, 0.3 and
7850kg/m³ respectively.
Sintering of ceramics may exhibit the following characteristics:
Select one or more:
a. It involves the high-pressure deformation of a pre-existing shape into a new form
b. The total surface area (including internal area) decreases
C.
Pores become smaller
d. Pores become larger on average
Parts of the material may become amorphous
Of. The surface energy of the system increases
e.
Chapter 5 Solutions
The Science and Engineering of Materials (MindTap Course List)
Ch. 5 - What is the driving force for diffusion?Ch. 5 - Give three examples of materials processes that...Ch. 5 - In the carburization treatment of steels, what are...Ch. 5 - Prob. 5.4PCh. 5 - Prob. 5.5PCh. 5 - Prob. 5.6PCh. 5 - Prob. 5.7PCh. 5 - A certain mechanical component is heat treated...Ch. 5 - Prob. 5.9PCh. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - Prob. 5.12PCh. 5 - Prob. 5.13PCh. 5 - Prob. 5.14PCh. 5 - Prob. 5.15PCh. 5 - Prob. 5.16PCh. 5 - Compare the diffusion coefficients of carb on in...Ch. 5 - Prob. 5.18PCh. 5 - Activation energy is sometimes expressed as...Ch. 5 - Prob. 5.20PCh. 5 - The activation energy for the diffusion of copper...Ch. 5 - Prob. 5.22PCh. 5 - Prob. 5.23PCh. 5 - Prob. 5.24PCh. 5 - Prob. 5.25PCh. 5 - Write down Fick’s first law of diffusion. Clearly...Ch. 5 - Prob. 5.27PCh. 5 - Prob. 5.28PCh. 5 - Prob. 5.29PCh. 5 - Prob. 5.30PCh. 5 - A 1-mm-thick BCC iron foil is used to separate a...Ch. 5 - Prob. 5.32PCh. 5 - Prob. 5.33PCh. 5 - A 0.001 in. BCC iron foil is used to separate a...Ch. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - Prob. 5.40PCh. 5 - Prob. 5.41PCh. 5 - Prob. 5.42PCh. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - Prob. 5.45PCh. 5 - Prob. 5.46PCh. 5 - Prob. 5.47PCh. 5 - Prob. 5.48PCh. 5 - Pure zinc is to be diffused into copper by dipping...Ch. 5 - Nitriding is a process in which nitrogen is...Ch. 5 - Determine the carburizing time necessary to...Ch. 5 - Prob. 5.52PCh. 5 - Prob. 5.53PCh. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - Prob. 5.56PCh. 5 - Prob. 5.57PCh. 5 - Prob. 5.58PCh. 5 - Compare the rate at which oxygen ions diffuse in...Ch. 5 - Prob. 5.60PCh. 5 - Prob. 5.61PCh. 5 - Prob. 5.62PCh. 5 - Prob. 5.63PCh. 5 - Prob. 5.64PCh. 5 - Prob. 5.65PCh. 5 - A 0.80% C steel must operate at 950°C in an...Ch. 5 - Prob. 5.67PCh. 5 - Prob. 5.68PCh. 5 - Prob. 5.69PCh. 5 - Prob. 5.70PCh. 5 - Prob. 5.71PCh. 5 - Prob. 5.72PCh. 5 - Most metals and alloys can be processed using the...Ch. 5 - Prob. 5.74PCh. 5 - Prob. 5.75PCh. 5 - Prob. 5.76PCh. 5 - A ceramic part made from MgO is sintered...Ch. 5 - Prob. 5.78PCh. 5 - What are the advantages of using hot pressing and...Ch. 5 - Prob. 5.80PCh. 5 - Prob. 5.81DPCh. 5 - Design a spherical tank, with a will thickness of...Ch. 5 - Prob. 5.83DPCh. 5 - Prob. 5.84DPCh. 5 - Prob. 5.85DPCh. 5 - Prob. 5.86CPCh. 5 - Prob. 5.87CPCh. 5 - Prob. 5.88CPCh. 5 - Prob. 5.1KP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain sintering and provide an ICT diagram of the processarrow_forwardSintering of ceramics may exhibit the following characteristics: Select one or more: a. The surface energy of the system increases b. It involves the high-pressure deformation of a pre-existing shape into a new form c. Pores become larger on average d. Pores become smaller e. Parts of the material may become amorphous f. The total surface area (including internal area) decreasesarrow_forwardThe part shown in Figure is to be pressed from fine copper powders using a compaction pressure of 1000 MPa. Dimensions are milimetres. Determine a) the required press tonnage to perform this operation b) the final weight of the part if the porosity is 15%. Assume shrinkage during sintering can be neglected. (the desity of copper =8,97g/cm³ ) 65 30 25 12 20arrow_forward
- Which of the following processes are the plastic forming methods used in the shaping of traditional ceramics (three correct answers): Odry pressing O extrusion O jangling O jiggering O jolleying Oslip casting O spinningarrow_forward2) The part shown in Figure is to be pressed from fine copper powders using a compaction pressure of 1000 MPa. Dimensions are milimetres. Determinea) the required press tonnage to perform this operationb) the final weight of the part if the porosity is 15%. Assume shrinkage during sintering can be neglected. (the desity of copper =8,97g/cm3 )arrow_forwardQuestion 6 During an extrusion process, a chromium billet at a temperature of 1300°C, need to be extruded from a billet diameter of 13 mm to a final diameter of 0.35 mm. An extrusion die are required to withstand the temperature and forces occurring during the process. 6.1 Which ceramic material will you suggest for this application? Provide reasons for your selection. 6.2 If the ceramic material, selected in Question 6.1 have an UTS. = 915 MPa, porosity of 16 % and n = 4, calculate the tensile strength and elastic modulus of the ceramic at room temperature.arrow_forward
- In solid state sintering of compacted metal powder material, discuss how the progress of microstructure changes in sintering can be observed by microscopy. Support your discussion with suitable schematic diagram. (Word limit: ~100)arrow_forwardQuestion 3: a) What is solid state sintering? How is solid state sintering classified. What are the distinct features of each stage. Briefly explain your answer. b) What are the two main differences between solid state sintering and liquid phase sintering.arrow_forwardAn extruder has barrel diameter and length of 150 mm and 3.1 m, respectively. The screw rotational speed = 55 rev/min, channel depth = 8 mm, and flight angle = 18°. The plastic melt has a shear viscosity = 175 Pa-s. Determine: (a) the extruder characteristic, (b) the shape factor Ks for a circular die opening with diameter = 4.0 mm and length = 15 mm, and (c) the operating point (Q and p).arrow_forward
- GKN Sinter Metals Company pressed iron powders using a compaction pressure of 600 MPa to produced a cylindrical bearing which is 70 cm long and has internal and external diameters of 8 cm and 16 cm, respectively. Determine (a) the most appropriate pressing direction, (b) the required press tonnage to perform this operation, and (c) the final weight of the part if the porosity is 12%, given that the density of iron, ρ = 7.87 g/cm3. Assume shrinkage during sintering can be neglectedarrow_forwardQ. Discuss the following sentences: 1- A wide particle size distribution is preferred for dry pressing. 2- Products with high dimension accuracy are obtained in hot pressed technique.arrow_forwardWhat is Blow molding process? Describe extrusion blow molding and injection blow molding. What are the advantages of multilayer blow molding?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Explanation of Solidification of Metals & Alloys | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=G5z9KknF_s8;License: Standard Youtube License