EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 6, Problem 6.28P
Interpretation Introduction
Interpretation:
The rate of moisture condensation and the volumetric flow rate of air should be calculated.
Concept introduction:
The
Where, the volume (V) occupied by ‘n’ moles of any gas has a pressure (P) at temperature (T) in Kelvin and ‘R’ = Gas constant
Antoine equation
Antoine equations describe the relationship between vapor pressure and temperature for pure components. This is a semi-empirical relationship.
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
A steel cylinder containing compressed air is stored in a fermentation laboratory ready to provide aeration
gas to a small-scale bioreactor. The capacity of the cylinder is 48 liters, the absolute pressure is 0.35 MPa
and the temperature is 22°C. One day in mid-summer when the air conditioning breaks down, the
temperature in the laboratory rises to 33°C and the valve at the top of the cylinder is accidentally left open.
Estimate the proportion of air that will be lost.
P1A.6 The molar mass of a newly synthesized fluorocarbon was measured in a gas microbalance. is device consists of a glass bulb forming one end of a beam, the whole surrounded by a closed container. The beam is pivoted, and the balance point is attained by raising the pressure of gas in the container, so increasing the buoyancy of the enclosed bulb. In one experiment, the balance point was reached when the fluorocarbon pressure was 327.10Torr; for the same setting of the pivot, a balance was reached when CHF3 (M = 70.014 g mol−1) was introduced at 423.22 Torr. A repeat of the experiment with a di erent setting of the pivot required a pressure of 293.22 Torr of the uorocarbon and 427.22 Torr of the CHF3. What is the molar mass of the fluorocarbon? Suggest a molecular formula.
Calculate the total mass of precipitable water (the answer in tons) in the saturated air column
9.5 km high above 4.8 km2 (square kilometers) of the ground surface. The surface pressure is
101.2 kPa, the surface air temperature is 23 °C, and the lapse rate is 6.1°C/km. Taking the
increment in elevation by 1.5 km, the gas constant Ra can be considered as 287 J/kg-K.
A) 251941.114
B) 219425.876
C) 941251.411
D) 114941.251
E) None of the above
Chapter 6 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 6 - Ten mL of pure liquid water in a cylinder with a...Ch. 6 - A quantity of methyl acetate is placed in an open,...Ch. 6 - Ethyl alcohol has a vapor pressure of 20.0 mm Hg...Ch. 6 - Prob. 6.4PCh. 6 - Prob. 6.5PCh. 6 - Prob. 6.6PCh. 6 - Prob. 6.7PCh. 6 - Prob. 6.8PCh. 6 - Prob. 6.9PCh. 6 - Prob. 6.10P
Ch. 6 - Prob. 6.11PCh. 6 - Prob. 6.12PCh. 6 - Prob. 6.13PCh. 6 - Air at 50% relative humidity is cooled...Ch. 6 - Prob. 6.15PCh. 6 - Prob. 6.16PCh. 6 - Air at 90°C and 1.00 atm (absolute) contains 10.0...Ch. 6 - When fermentation units are operated with high...Ch. 6 - When you step out of a shower, the temperature in...Ch. 6 - A fuel cell is an electrochemical device in which...Ch. 6 - Prob. 6.21PCh. 6 - Prob. 6.22PCh. 6 - Prob. 6.23PCh. 6 - Prob. 6.24PCh. 6 - Prob. 6.25PCh. 6 - Prob. 6.26PCh. 6 - Prob. 6.27PCh. 6 - Prob. 6.28PCh. 6 - An air conditioner is designed to bring 10.000...Ch. 6 - Prob. 6.30PCh. 6 - Prob. 6.31PCh. 6 - Prob. 6.32PCh. 6 - A gas stream containing 40.0 mole% hydrogen, 35.0%...Ch. 6 - Prob. 6.34PCh. 6 - In the manufacture of an active pharmaceutical...Ch. 6 - Prob. 6.36PCh. 6 - In the ?nal stage of the manufacturing process...Ch. 6 - Prob. 6.38PCh. 6 - A fuel gas containing methane and ethane is burned...Ch. 6 - A mixture of propane and butane is burned with...Ch. 6 - An important parameter in the design of gas...Ch. 6 - A liquid stream consisting of 12.5 mole% n-butane...Ch. 6 - Nitric acid is a chemical intermediate primarily...Ch. 6 - Prob. 6.44PCh. 6 - Sulfur trioxide (SO3) dissolves in and reacts with...Ch. 6 - State whether you would use Raoult’s law or Henrys...Ch. 6 - A gas containing nitrogen, benzene, and toluene is...Ch. 6 - Prob. 6.48PCh. 6 - Prob. 6.49PCh. 6 - A conelation for methane solubility in...Ch. 6 - Prob. 6.51PCh. 6 - The constituent partial pressures of a gas in...Ch. 6 - Prob. 6.53PCh. 6 - Prob. 6.54PCh. 6 - Prob. 6.55PCh. 6 - Prob. 6.56PCh. 6 - Prob. 6.57PCh. 6 - Prob. 6.58PCh. 6 - Nitrogen is bubbled through a liquid mixture that...Ch. 6 - Prob. 6.60PCh. 6 - Prob. 6.61PCh. 6 - Prob. 6.62PCh. 6 - The feed to a distillation column (sketched below)...Ch. 6 - Prob. 6.64PCh. 6 - Prob. 6.65PCh. 6 - Prob. 6.66PCh. 6 - Prob. 6.67PCh. 6 - Prob. 6.68PCh. 6 - Prob. 6.69PCh. 6 - Prob. 6.70PCh. 6 - A methanol-water feed stream is introduced to a...Ch. 6 - Prob. 6.72PCh. 6 - In this problem you will use a spreadsheet to...Ch. 6 - Prob. 6.74PCh. 6 - Prob. 6.75PCh. 6 - Prob. 6.76PCh. 6 - Acetaldehyde is synthesized by the catalytic...Ch. 6 - Dehydration of natural gas is necessary to prevent...Ch. 6 - A two-unit process is used to separate H2S from a...Ch. 6 - Prob. 6.80PCh. 6 - Prob. 6.81PCh. 6 - Prob. 6.82PCh. 6 - Prob. 6.83PCh. 6 - A solution containing 100 lbm KNO3/100 Ibm H2O at...Ch. 6 - A 10.0 wt% aqueous solution of sodium chloride is...Ch. 6 - Potassium dichromate (K2Cr2O7) is to be recovered...Ch. 6 - Prob. 6.87PCh. 6 - Prob. 6.88PCh. 6 - Sodium bicarbonate is synthesized by reacting...Ch. 6 - An ore containing 90 wt% MgSO4(H2O and the balance...Ch. 6 - An aqueous waste stream leaving a process contains...Ch. 6 - A solution of diphenyl (MW = 154.2) in benzene is...Ch. 6 - An aqueous solution of urea (MW = 60.06) freezes...Ch. 6 - Prob. 6.94PCh. 6 - Derive Equation 6.54 for the boiling-point...Ch. 6 - Prob. 6.96PCh. 6 - A stream of 5.00 wt% oleic acid in cottonseed oil...Ch. 6 - Benzene and hexane are being considered as...Ch. 6 - Acetone is lo be extracted with n-hexane from a...Ch. 6 - Prob. 6.100PCh. 6 - Prob. 6.101PCh. 6 - Five kilograms of a 30 wt% acetone70% water...Ch. 6 - An aqueous acetone solution is fed at a rate of...Ch. 6 - Prob. 6.104PCh. 6 - Prob. 6.105PCh. 6 - Air at 25°C and 1 atm with a relative humidity of...Ch. 6 - Prob. 6.107PCh. 6 - Prob. 6.108PCh. 6 - Various amounts of activated carbon were added to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- P1A.6 The molar mass of a newly synthesized fluorocarbon was measured in a gas microbalance. is device consists of a glass bulb forming one end of a beam, the whole surrounded by a closed container. e beam is pivoted, and the balance point is attained by raising the pressure of gas in the container, so increasing the buoyancy of the enclosed bulb. In one experiment, the balance point was reached when the fluorocarbon pressure was 327.10Torr; for the same setting of the pivot, a balance was reached when CHF3 (M = 70.014 g mol−1) was introduced at 423.22 Torr. A repeat of the experiment with a di erent setting of the pivot required a pressure of 293.22 Torr of the uorocarbon and 427.22 Torr of the CHF3. What is the molar mass of the fluorocarbon? Suggest a molecular formula.arrow_forwardA solid fuel, described by the chemical structure below, is combusted in 10% excess air. If necessary, clearly state any assumptions required to develop your solution. H Н —с — N — с — s — н | || 0 = C S H (a) Determine the mass feed rate (g/min) of the fuel such that 10,000 m³/min of total flue gas is generated at 1500 °C and 1 atm. (b) Determine the effluent SO2 concentration (ppm,) at STP and dry conditions.arrow_forwardAn air conditioner cools 226 m3/min of humid air at 36°C and 98% relative humidity to 10°C.(a) Do a degree-of-freedom analysis to prove that enough information is available to determine the required cooling duty (rate of heat transfer).(b) Calculate the rate of condensation of water in the unit and the cooling duty in tons (1 ton = 12,000 Btu/h).arrow_forward
- One kg of butane (C4H10) is burned with 25 kg of air at 30 ° C and 90 kPa. Full of combustion and products assuming a pressure of 90 kPa, the theoretical amount of air used and the dew point of the products.arrow_forwardProducer gas is a fuel that is manufactured from the reaction of coal, steam and air. A producer gas has the following composition by volume (dry basis): 20.35% CO, 11.03%, CO2, 15% H2, 51.43% N2, 1.98%O2 and 0.21 % CH4. The gas is flowing at 6000 cfm. It has a temperature of 200℃ , a pressure of 21 cm Hg and a partial pressure of 50 mm Hg for H2O. The atmospheric pressure is 758 mm Hg. The gas is delivered from the source to the furnace by means of a pipe. It cools down to 50 ℃ and is compressed to 2 atm pressure. At this condition, calculate:1. the volumetric flow ate2. the mass flow rate3. the partial pressure of each component/including water)4. complete analysis of the mixturearrow_forwardThe pKw of ammonia in water varies with temperature as follows :θ/°C 10 15 20 25 30 35pKw 4.798 4.782 4.767 4.759 4.740 4.733Deduce as much information as you can from these values.arrow_forward
- Ethanol vapours were allowed to completely fill a jug with a volume of 18.9L. The ethanol was burned yielding 9.6mL of LIQUID water in the bottom of the jug. C2H5OH + 3 O2 ---> 2 CO2 + 3H20 If the room temperatue was 23.5 degrees Celsius and the pressure was 97.5 KpA, calculate the percentage yield of the water gathered in the jug. Select the final answer from the options below: - Not enough information - 76% - 24% - 17%arrow_forward1. 0.45 kg of carbon monoxide (28) and 1 kg of air at 15°C are contained in a vessel of volume 0.4 m'. Calculate the partial pressure of each constituent and the total pressure in the vessel. The gravimetric analysis of air is to be taken as 23.3% oxygen (32) and 76.7% nitrogen (28). IAns. Po, = 0.4359 bar; PN, = 1.64 bar, Poo = 0.962 bar]arrow_forwardQ1/ The ideal gas equation of state is given by: PV = nRT Where: P is the pressure (atm), V is the volume (L), 7 is the temperature (K), R=0.08206 (L atm)/(mol K) is the gas constant, and n is the number of moles. Real gases, especially at high pressures, deviate from this behavior. Their responses can be modeled with the van der Waals equation: nRT V-nb Where a and b are material constants. For CO₂ a 3.5924 L'atm/mol², and b=0.04267 L/mol. Calculate P from both equations for CO₂ gas with 40 values of V between 0.01 and 1.5 and display the results in: 1- Three-column table where the values of Vand both P are displayed in the first, second, and third columns, respectively. 2-Plot V versus both P in two different plots in the same figure with a solid line, black color, with circle marker. Add a title, labels, and the grid to the plot. Make all texts bold with font size of 13. Take T=298K and n=3 moles. nº a + √² Parrow_forward
- 1. A wet gas from a field in Iran is processed through two stages of separation; first stage separator operates at 220 psia and 71°F, while the stock tank operates at atmospheric pressure and 69°F. The separator gas condensate ratio is 41,000 scf/STB and the stock tank gas condensate ratio is 450 scf/STB. The molecular weights of the separator gas and stock tank gas are 25.0 and 35.0 lb/lb-mol, respectively. The stock tank condensate gravity is 0.85 and its molecular weight is 125 lb/lb-mol. Let us calculate the specific gravity of the reservoir gas in a step-wise manner, by considering quantities for one STB of condensate. Note that 1.0 bbl is 5.614 ft. Separator gas MWsg = 25 lb/lb-mol 41,000 scf/STB Reservoir gas 1st stage separator 220 psia and 71°F Stock tank gas MWsg = 35 lb/lb-mol 450 scf/STB 2nd stage separator (Stock tank) 14.7 psia and 69°F MW=125 lb/lb-mol SGstc = 0.85 Stock tank condensate a. to one STB. Calculate the mole number [lb-mole] of the stock tank condensate that…arrow_forward20. A mixture consisting of 6 kg of O, and 9 kg of N, has a pressure of 3 bar and temperature of 20°C. For the mixture determine the following : (i) The mole fraction of each component ; (iii) The specific gas constant; (v) The partial pressures and partial volumes. (ii) The average molecular weight ; (iv) The volume and density; [Ans. (i) 0.3684, 0.6315 ; (iüi) 29.475 ; (iii) 0.282 kJ/kg K ; (iv) 4.13 m?, 3.629 kg/m² ; (v) 1.1 bar, 1.894 bar ; 1.52 m², 2.61 m²)arrow_forwardQuestions 15 through 17 pertain to the situation described below: An air tank of volume 2.70 x 10-2 m³ has air pressure 7.30 x 106 Pa and temperature 30.0°C inside and is left at a lake bottom at 15.0°C. If there is a leak on the tank and the pressure and temperature inside have dropped to 2.70 × 106 Pa and 11.0°C over a period of time. (15) How many moles of air are in the tank initially? (A) 70.2 mol; (B) 72.2 mol; (C) 74.2 mol; (D) 76.2 mol; (E) 78.2 mol. (16) How many moles of air have leaked out of the tank? (A) 39.3 mol; (B) 41.3 mol; (C) 43.3 mol; (D) 45.3 mol; (E) 47.3 mol. (17) What is the work done by the air leaked into the water? (A) 143 kJ; (B) 133 kJ; (C) 123 kJ; (D) 113 kJ; (E) 103 kJ.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill EducationPrinciples of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
- Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill EducationChemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage LearningElementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305957404/9781305957404_smallCoverImage.gif)
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781259911156/9781259911156_smallCoverImage.gif)
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305577213/9781305577213_smallCoverImage.gif)
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9780078021558/9780078021558_smallCoverImage.gif)
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305079373/9781305079373_smallCoverImage.gif)
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781118431221/9781118431221_smallCoverImage.gif)
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY