EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 4.23P
A stream of humid air containing 1.50 mole% H2O(v) and the balance dry air is to be humidified to a water content of 10.0mole% H?O. For this purpose, liquid water is fed through a flowmeter and evaporated into the air stream. The flowmeter reading, R, is 95. The only available calibration data for the flowmeter are two points scribbled on a sheet of paper, indicating that readings R = 15 and R = 50 correspond to flow rates V = 40.0 ft3/h and V = 96.9 fP/h, respectively.
(a) Assuming that the process is working as intended, draw and label the flowchart, do the degree-of- freedom analysis, and estimate the molar flow rate (lb-mole/h) of the humidified (outlet) air if (i) the volumetric flow rate is a linear function of R and (ii) the reading R is a linear function of V .
(h) Suppose the outlet air is analyzed and found to contain only 7% water instead of the desired 10%. List as many possible reasons as you can think of for the discrepancy, concentrating on assumptions made in the calculation of Part (a) that might be violated in the real process.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A hydrocarbon stream composed of 40 mol% n-butane and 60 mol% n-octane is fed at 100 kmol/h to a flash vessel operating at 5 bar and 145°C. The liquid outlet stream of the flash vessel is then sent to a distillation column with a partial condenser to further separate the components. 90% of the butane in the feed to the column is recovered in the overhead vapor product (distillate), along with small amounts of octane. The bottoms product contains octane which accounts for 75% of the octane in the fresh hydrocarbon feed (to the flash vessel). The condenser and reboiler operating temperatures are 136.7°C and 165.7°C, respectively. Determine the compositions of the liquid outlet stream of the condenser and the vapor outlet stream of the reboiler.
A mixture containing 42 wt% benzene (B) and 58 wt% toluene (T) is fed to a distillation column at a flow rate of 100 kg per minute. The product steam leaving the top of the column (the overhead product) contains 90 wt% benzene and 85 wt% of the total benzene fed to the column exits in this overhead product stream.
Calculate the mass flow rate and mass composition of the product stream leaving the bottom of the column. Calculate the volumetric flow rate of the overhead product, assuming that it exits the distillation column as a vapour stream at 82C and 1 atm (abs).
Physical Property Data (S.G.= specific gravity) from table B-1:
Benzene
S.G. = 0.879
MW = 78.11 g/mol
Toluene
S.G. = 0.866
MW = 92.13 g/mol
Water
Density = 1.00 kg/L
MW = 18.02 g/mol
R = 0.08206 L atm/mol K
A steady-state process to recover crystalline potassium chromate (K,CrOz) from an aqueous solution of this salt
is required. Four thousand kilograms per hour of a solution that is one-third K,CrO, by mass is joined by a recycle
stream containing 36.4% K2CrO7, and the combined stream is fed into an evaporator. The concentrated stream
leaving the evaporator contains 49.4% K,CrO; this stream is fed into a crystallizer in which it is cooled (causing
crystals of K,CrO, to come out of solution) and then filtered. The filter cake consists of K,CrO, crystals and a
solution that contains 36.4% K,CrO, by mass; the crystals account for 95% of the total mass of the filter cake. The
solution that passes through the filter, also 36.4% K,CrO,, is the recycle stream.
1- Draw the flowchart of the system and put all known information.
2- Calculate the rate of evaporation, the rate of production of crystalline K,CrO7, the feed rates that the
evaporator and the crystallizer must be designed to handle, and…
Chapter 4 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 4 - Prob. 4.1PCh. 4 - Rain is falling on a poorly designed 150-m" flat...Ch. 4 - A liquid-phase chemical reaction A -* B takes...Ch. 4 - A stream consisting of 44.6 mole% benzene and...Ch. 4 - Prob. 4.5PCh. 4 - A liquid mixture of acetone and water contains 35...Ch. 4 - Prob. 4.7PCh. 4 - Prob. 4.8PCh. 4 - Inside a distillation column (see Problem 4.8), a...Ch. 4 - Prob. 4.10P
Ch. 4 - In the production of soybean oil, dried and flaked...Ch. 4 - Prob. 4.12PCh. 4 - A process is carried out in which a mixture...Ch. 4 - Strawberries contain about 15wt% solids and 85wt%...Ch. 4 - Two streams flow into a 500-gallon tank. The first...Ch. 4 - A fuel distributor supplies four liquid fuels,...Ch. 4 - Prob. 4.17PCh. 4 - One thousand kilograms per hour of a mixture...Ch. 4 - L-Serine is an amino acid that often is provided...Ch. 4 - A 100 kmol/h stream that is 97 mole% carbon...Ch. 4 - A pharmaceutical product, P, is made in a batch...Ch. 4 - A liquid mixture containing ethanol (55.0 wt%) and...Ch. 4 - A stream of humid air containing 1.50 mole% H2O(v)...Ch. 4 - A liquid mixture contains 60.0 wt% ethanol (E),...Ch. 4 - Certain vegetables and fruits contain plant...Ch. 4 - Two aqueous sulfuric acid solutions containing...Ch. 4 - A paint mixture containing 25.0% of a pigment and...Ch. 4 - In the commercial production of sugar (sucrose),...Ch. 4 - Prob. 4.29PCh. 4 - A garment to protect the wearer from toxic agents...Ch. 4 - A dilute aqueous solution of H2SO4 (Solution A) is...Ch. 4 - Gas streams containing hydrogen and nitrogen in...Ch. 4 - An artificial kidney is a device that removes...Ch. 4 - The indicator-dilution method is a technique used...Ch. 4 - Prob. 4.35PCh. 4 - Gas absorption or gas scrubbing is a commonly used...Ch. 4 - The SO2 scrubbing tower described in Problem 4.36...Ch. 4 - Prob. 4.38PCh. 4 - The hormone estrogen is produced in the ovaries of...Ch. 4 - A liquid mixture containing 30.0mole% benzene (B),...Ch. 4 - Seawater containing 3.50 wt% salt passes through a...Ch. 4 - Inside the column a liquid stream flows downward...Ch. 4 - Prob. 4.43PCh. 4 - Effluents from metal-finishing plants have the...Ch. 4 - In an absorption tower (or absorber), a gas is...Ch. 4 - In the production of a bean oil, beans containing...Ch. 4 - Boilers are used in most chemical plants to...Ch. 4 - Following is a diagram of the shirt-cleaning...Ch. 4 - A drug (D) is produced in a three-stage extraction...Ch. 4 - Prob. 4.52PCh. 4 - Ammonia is oxidized to nitric oxide in the...Ch. 4 - Prob. 4.54PCh. 4 - A stream containing H2S and inert gases and a...Ch. 4 - 436. The reaction between ethylene and hydrogen...Ch. 4 - Prob. 4.57PCh. 4 - Prob. 4.58PCh. 4 - Titanium dioxide (TiCb) is used extensively as a...Ch. 4 - Prob. 4.60PCh. 4 - Prob. 4.61PCh. 4 - Oxygen consumed by a living organism in aerobic...Ch. 4 - A genetically engineered strain of Escherichia...Ch. 4 - The gas-phase reaction between methanol and acetic...Ch. 4 - Prob. 4.65PCh. 4 - Prob. 4.66PCh. 4 - Methane and oxygen react in the presence of a...Ch. 4 - Ethane is chlorinated in a continuous reactor:...Ch. 4 - Ethanol can be produced commercially by the...Ch. 4 - Prob. 4.70PCh. 4 - Solid calcium fluoride (CaF2) reacts with sulfuric...Ch. 4 - Prob. 4.72PCh. 4 - Chlorobenzene (C^HsCl), an important solvent and...Ch. 4 - A catalytic reactor is used to produce...Ch. 4 - 4.7'6. Methanol is produced by reacting carbon...Ch. 4 - Methane reacts with chlorine to produce methyl...Ch. 4 - Ethylene oxide is produced by the catalytic...Ch. 4 - Methanol is synthesized from carbon monoxide and...Ch. 4 - The fresh feed to an ammonia production process...Ch. 4 - A gas contains 75.0 wt% methane. 10.0% ethane....Ch. 4 - Five liters of liquid n-hexane and 4 liters of...Ch. 4 - Gasoline, which we will represent as having the...Ch. 4 - Prob. 4.87PCh. 4 - Natural gas containing a mixture of methane,...Ch. 4 - Propane is burned completely with excess oxygen....Ch. 4 - Prob. 4.91PCh. 4 - Prob. 4.92PCh. 4 - Liquid methanol is fed to a space heater at a rate...Ch. 4 - Prob. 4.94PCh. 4 - Prob. 4.95PCh. 4 - A fuel oil is analyzed and found to contain 85.0...Ch. 4 - Prob. 4.97PCh. 4 - Prob. 4.98PCh. 4 - Prob. 4.99PCh. 4 - 4.1 (Mt. You have been sent by the Environmental...Ch. 4 - Fuel oils contain primarily organic compounds and...
Additional Science Textbook Solutions
Find more solutions based on key concepts
Using PFE where required, find X(t) for a. X(s)=s(s+1)(s+2)(s+3)(s+4) b. X(s)=s+2( s+1)2 c. X(s)=1s2+s+1 d. X(s...
Process Dynamics and Control, 4e
The gas-phase reaction
is to be carried out isothermally first in a flow reactor. The molar feed is 50% H2 and...
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
3.1 Discuss the differences between an error and a residual.
Elementary Surveying (14th Edition)
The _____ function reads a line of text from a file.
Starting Out with C++ from Control Structures to Objects (8th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- Feed gas containing of 78.5mol % H₂, 21% of N₂ & 0.5% of Ar is mixed with recycle gas and enters a reactor where 15% N₂ is converted to NH3 as per the reaction. Ammonia from the exit of the reactor is completely separated from unconverted gases. To avoid the buildup of inerts, a small fraction (5%) of the unreacted gases purged and the balance recycled. USING ASPEN/HYSYS Draw the process flow sheet Product rate and Purge rate Basis:100mol/hrarrow_forwardA gaseous fuel containing methane and ethane is burned with excess air. The fuel enters the furnace at 25°C and 1 atm, and the air enters at 200°C and 1 atm. The stack gas leaves the furnace at 800°C and 1 atm and contains 5.32 mole% CO2, 1.60% CO, 7.32% O₂, 12.24% H₂O, and the balance ₂. 1. Calculate the molar percentages of methane and ethane in the fuel gas and the percentage excess air fed to the reactor. 2. Calculate the heat (kJ) transferred from the reactor per cubic meter of fuel gas fed. 3. A proposal has been made to lower the feed rate of air to the furnace. State advantages and a drawback of doing so.arrow_forwardThe boiler in an apartment building uses propane (C3H8) to heat water that circulates throughout the building as steam. 1.00 m'/s of propane gas at 25°C and 1 atm is combusted with 10% excess air at 25°C and 1 atm. After all of the propane is combusted, the product gas contains a 10.0:1 molar ratio of CO2 to CO and leaves the boiler at 25°C. Heat from the boiler is transferred to a pure water stream at 50°C and 1.0 bar, which is converted into saturated steam at 20 bar, with no heat lost to the surroundings in the process. What mass of water is heated in this process? Molecule (Formula) (kJ/mol) -393.5 (g) Carbon dioxide (CO2) Carbon -110.52 (g) monoxide (CO) Hydrogen (H2) Nitrogen (N2) Охуgen (O2) Propane (C;Hs) Hot Water (out). Flue Gas Shutoff Valve - Cold Water (in) -119.8(1) -103.8(g) -285.84(1) Gas Supply Line- Cold Water Shutoff Valve Water (H20) -241.83(g) Temperature / Pressure Relief Valve Water Line Overflow Pipe. Tank Insulation - Dip Tube Drain Valve Gas Burner Control-…arrow_forward
- Q4/in a two stage process, acetic acid (A)is extracted from water (W) into hexanol (H) in a liquid-liquid extraction vessel and the extract is subsequently separated by distillation. Assume that water is completely insoluble in hexanol. A mixture of 18wt% acetic acid and the balance water is feed to liquid-liquid extraction vessel. Pure hexanol is feed to the column to extracted the acetic acid. The water-rich stream leaving the vessel is 99.5wt% water and the balance acetic acid. The hexanol-rich extract from the vessel is feed to a distillation column. The composition of the distillate is 96wt% acetic acid and the balance hexanol. The bottom stream contains 97.2wt% hexanol and recovers 95% of the hexanol feed to the liquid-liquid extraction vessel. Calculate the percentage of acetic acid in the process feed that is recovered in the distillate stream. Distillation Liq-liq Column Extractionarrow_forward4.64. The gas-phase reaction between methanol and acetic acid to form methyl acetate and water CH;OH + CH3COOH = CH3COOCH3 + H2O (A) (В) (C) (D) takes place in a batch reactor. When the reaction mixture comes to equilibrium, the mole fractions of the four reactive species are related by the reaction eqilibrium constant Ky : = 4.87 YAYB (a) Suppose the feed to the reactor consists of n40,NB0, NCo, NDO, and no gram-moles of A, B, C, D, and an inert gas, I, respectively. Let į be the extent of reaction. Write expressions for the gram-moles of each reactive species in the final product, nA(2), nB(3), nc(E), and np(3). Then use these expressions and the given equilibrium constant to derive an equation for , the equilibrium extent of reaction, in terms of n20,.., N1o. (see Example 4.6-2.) (b) If the feed to the reactor contains equimolar quantities of methanol and acetic acid and no other species, calculate the equilibrium fractional conversion. (c) It is desired to produce 70 mol of methyl…arrow_forwardThe proximate analysis (% air dried basis), the ultimate analysis (% d.m.m.f basis) and experimental gross calorific value (kcal/kg on air dried basis) is as follows: Proximate Ultimate analysis C.V. analysis % % Kcal/kg M VM А FC C HONS (exp. Value) 29 16 53 86 6 5 217200 Calculate its gross calorific value and net calorific value using (i) Goutal & (ii) Mazumdar correlations.arrow_forward
- Nitrogen is to be liquefied in a simple Linde process. The feed and recycle are mixed. compressed to 64 bar, and precooled to 135K. The vapor then passes through a heat exchanger for additional cooling before beinng throttled to 1 bar. The unliquefied fraction leaves the seperator at the saturation temperature and passes through the heat exchanger, then exits at 120 K. a. What fraction of the gas is liquefied in the process? b. What is the temperature of the high pressure gas entering the throttle valve?arrow_forwardSolid calcium (CaF2) reacts with sulfuric acid to form solid calcium sulfate and gaseous hydrogen fluoride. The HF is then dissolved in water to form hydrofluoric acid. A source of calcium fluoride is fluorite ore containing 96 wt% CaF2 and 4% SiO2. In a typical hydrofluoric acid manufacturing process, fluorite ore is reacted with 93 wt% aqueous sulfuric acid, supplied 15% in excess of the stoichiometric amount. Ninety-five percent of the ore dissolves in the acid. Some of the HF formed reacts with the dissolved silica in the reaction 6 HF + SIO2 (aq) – H2SİF6 (9) + 2 H2O (1) The hydrogen fluoride exiting from the reactor is subsequently dissolved in enough water to produce 60 wt% hydrofluoric acid. Calculate the quantity of fluorite ore needed to produce a metric ton of acid. Express your answer into three significant figures.arrow_forwardAn underfeed stoker feeds coal to a boiler at the rate of 100 kg/hr. The ultimate analysis of coal is: C = 75.2 %, H;= 3.6 %, O2 = 7.4 %, N2 = 1.2 %, S = 2.1 % and the remaining is Ash. The dry refuse taken from the ash pit shows 20 % C and 80 % ash by weight. Orsat analysis of the flue gases gives the following composition, CO2 = 75.2 %, O, = 7.9 %, CO= 1 % Determine: a) m³ of air supplied per minute if the pressure is 100 kPaa and 20 °C; b) Total volume of flue gases flowing through the stack per minute if the temperature is 60 °C and pressure is 100 kPaa.arrow_forward
- 3. Given: Soda and lime are added to a glass batch in the form of soda ash (Na,CO,) and limestone (CaCO). During heating, these two ingredients decompose to give off carbon dioxide (CO₂), the resulting products being soda and lime. Find: Compute the weight of soda ash and limestone that must be added to 110 lb of quartz (SiO₂) to yield a glass of composition 72 wt% SiO₂, 16 wt% Na₂O, and 12 wt% Cao. Solution:arrow_forwardAn evaporation-crystallization process is used to obtain solid potassium sulfate from an aqueous solution of this salt. The fresh feed to the process contains 19.6% wt K2SO4 The wet filter cake consists of solid K2SO4 crystals and 40 % wt K2SO4 solution, in a ratio 10 kg crystals/kg solution. The filte a 40% solution is recycled to join the fresh food. Of the water fed to the evaporator, 45% is evaporated The evaporator has a maximum capacity of 175 kg/hr water evaporales Calculate a) The maximam production rate of solid K2SO4 b) The rate at which fresh feed must be supplied to achieve this production rate c) The ratio kg recycle kg fresh feedarrow_forwardTwo aqueous sulfuric acid solutions are available at a processing facility: 20.0 wt% H2SO4 (sg = 1.139) 60.0 wt% H2SO4 (sg = 1.498) It is desired to mix the two solutions such that the final product has a concentration of 4.00 M (sg-1.213). There is 100 kg of the 20% solution available. If all of this is to be used, calculate: The mass of 60% solution needed The mass and composition of the final productarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY
Mod-01 Lec-23 Degrees of freedom analysis; Author: nptelhrd;https://www.youtube.com/watch?v=c4h85JjrkzQ;License: Standard YouTube License, CC-BY
Introduction to Degrees of Freedom; Author: LearnChemE;https://www.youtube.com/watch?v=tW1ft4y5fQY;License: Standard Youtube License