EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
4th Edition
ISBN: 9781119192107
Author: BULLARD
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
thumb_up100%
Chapter 4, Problem 4.75P
A catalytic reactor is used to produce formaldehyde from methanol in the reaction CH3OH - HCHO + H2
A single-pass conversion of 60.0% is achieved in the reactor. The methanol in the reactor product is separated from the formaldehyde and hydrogen in a multiple-unit process. The production rate of formaldehyde is 900.0 kg/h.
- Calculate the required feed rate of methanol to the process (kmol/h) if there is no recycle.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2. In an ethanol production plant, a separator produces a 99% ethanol product from a feedstock
stream containing 85% water and 15% ethanol at a rate of 450 Ib/min. The separator has two
outlet streams: the ethanol product outlet stream (99% ethanol) and a residual water stream.
30% of the feedstock is bypassed and mixed with the residual water stream leaving the separator.
If 60% of the ethanol entering the separator is recovered in the product stream, determine the
composition of the residual water stream just after leaving the separator and the composition of the
residual stream after mixing with the bypass stream.
9. Ethane is burned with air in a continuous steady-state combustion reactor to yield a mixture of carbon monoxide, carbon dioxide, and water. The feed to the reactor contains 10 mol/min C2H6 and 200 mol/min air. The percentage conversion of ethane is 80%, and the gas leaving the reactor contains 8 mol CO2 per mol of CO. Determine the molar flow rate of the ethane gas in the product stream. (2 mol/min)
.edu bryuitra/courses roee_re
Question Completion Status:
The following process describes the complete combustion reaction of Toluene fuel C7HB (SG 0.866) with air. Liquid fuel (n1) enters the
combustion chamber at 200mL/min, where it evaporated into a stream of air (n2) 15% in excess. Complete combustion reaction in which
only fraction of the fuel is burned. The combustion products go to a condenser, where the unreacted fuel and water are liquified. The
mass flowrate of the fuel in this steam (ma) is 50. The uncondensed gas leaves the condenser at 60 C and 0.5 atm gauge pressure.
Calculate the fractional conversion of the fuel
Calculate the SCMH of the air entering the combustion chamber
Calculate the volumetric flow rate of the gas leaving the condenser (m³/min).
a.
b.
C.
ri4 CO2
n3 Fuel
ris N2
Fuel ri1
ni4 CO2
nig O2
Combustion
nig N2
Condenser
air riz
Chamber
ng O2
ni, H,0
n3 Fuel
niz H,0
Chapter 4 Solutions
EBK ELEMENTARY PRINCIPLES OF CHEMICAL P
Ch. 4 - Prob. 4.1PCh. 4 - Rain is falling on a poorly designed 150-m" flat...Ch. 4 - A liquid-phase chemical reaction A -* B takes...Ch. 4 - A stream consisting of 44.6 mole% benzene and...Ch. 4 - Prob. 4.5PCh. 4 - A liquid mixture of acetone and water contains 35...Ch. 4 - Prob. 4.7PCh. 4 - Prob. 4.8PCh. 4 - Inside a distillation column (see Problem 4.8), a...Ch. 4 - Prob. 4.10P
Ch. 4 - In the production of soybean oil, dried and flaked...Ch. 4 - Prob. 4.12PCh. 4 - A process is carried out in which a mixture...Ch. 4 - Strawberries contain about 15wt% solids and 85wt%...Ch. 4 - Two streams flow into a 500-gallon tank. The first...Ch. 4 - A fuel distributor supplies four liquid fuels,...Ch. 4 - Prob. 4.17PCh. 4 - One thousand kilograms per hour of a mixture...Ch. 4 - L-Serine is an amino acid that often is provided...Ch. 4 - A 100 kmol/h stream that is 97 mole% carbon...Ch. 4 - A pharmaceutical product, P, is made in a batch...Ch. 4 - A liquid mixture containing ethanol (55.0 wt%) and...Ch. 4 - A stream of humid air containing 1.50 mole% H2O(v)...Ch. 4 - A liquid mixture contains 60.0 wt% ethanol (E),...Ch. 4 - Certain vegetables and fruits contain plant...Ch. 4 - Two aqueous sulfuric acid solutions containing...Ch. 4 - A paint mixture containing 25.0% of a pigment and...Ch. 4 - In the commercial production of sugar (sucrose),...Ch. 4 - Prob. 4.29PCh. 4 - A garment to protect the wearer from toxic agents...Ch. 4 - A dilute aqueous solution of H2SO4 (Solution A) is...Ch. 4 - Gas streams containing hydrogen and nitrogen in...Ch. 4 - An artificial kidney is a device that removes...Ch. 4 - The indicator-dilution method is a technique used...Ch. 4 - Prob. 4.35PCh. 4 - Gas absorption or gas scrubbing is a commonly used...Ch. 4 - The SO2 scrubbing tower described in Problem 4.36...Ch. 4 - Prob. 4.38PCh. 4 - The hormone estrogen is produced in the ovaries of...Ch. 4 - A liquid mixture containing 30.0mole% benzene (B),...Ch. 4 - Seawater containing 3.50 wt% salt passes through a...Ch. 4 - Inside the column a liquid stream flows downward...Ch. 4 - Prob. 4.43PCh. 4 - Effluents from metal-finishing plants have the...Ch. 4 - In an absorption tower (or absorber), a gas is...Ch. 4 - In the production of a bean oil, beans containing...Ch. 4 - Boilers are used in most chemical plants to...Ch. 4 - Following is a diagram of the shirt-cleaning...Ch. 4 - A drug (D) is produced in a three-stage extraction...Ch. 4 - Prob. 4.52PCh. 4 - Ammonia is oxidized to nitric oxide in the...Ch. 4 - Prob. 4.54PCh. 4 - A stream containing H2S and inert gases and a...Ch. 4 - 436. The reaction between ethylene and hydrogen...Ch. 4 - Prob. 4.57PCh. 4 - Prob. 4.58PCh. 4 - Titanium dioxide (TiCb) is used extensively as a...Ch. 4 - Prob. 4.60PCh. 4 - Prob. 4.61PCh. 4 - Oxygen consumed by a living organism in aerobic...Ch. 4 - A genetically engineered strain of Escherichia...Ch. 4 - The gas-phase reaction between methanol and acetic...Ch. 4 - Prob. 4.65PCh. 4 - Prob. 4.66PCh. 4 - Methane and oxygen react in the presence of a...Ch. 4 - Ethane is chlorinated in a continuous reactor:...Ch. 4 - Ethanol can be produced commercially by the...Ch. 4 - Prob. 4.70PCh. 4 - Solid calcium fluoride (CaF2) reacts with sulfuric...Ch. 4 - Prob. 4.72PCh. 4 - Chlorobenzene (C^HsCl), an important solvent and...Ch. 4 - A catalytic reactor is used to produce...Ch. 4 - 4.7'6. Methanol is produced by reacting carbon...Ch. 4 - Methane reacts with chlorine to produce methyl...Ch. 4 - Ethylene oxide is produced by the catalytic...Ch. 4 - Methanol is synthesized from carbon monoxide and...Ch. 4 - The fresh feed to an ammonia production process...Ch. 4 - A gas contains 75.0 wt% methane. 10.0% ethane....Ch. 4 - Five liters of liquid n-hexane and 4 liters of...Ch. 4 - Gasoline, which we will represent as having the...Ch. 4 - Prob. 4.87PCh. 4 - Natural gas containing a mixture of methane,...Ch. 4 - Propane is burned completely with excess oxygen....Ch. 4 - Prob. 4.91PCh. 4 - Prob. 4.92PCh. 4 - Liquid methanol is fed to a space heater at a rate...Ch. 4 - Prob. 4.94PCh. 4 - Prob. 4.95PCh. 4 - A fuel oil is analyzed and found to contain 85.0...Ch. 4 - Prob. 4.97PCh. 4 - Prob. 4.98PCh. 4 - Prob. 4.99PCh. 4 - 4.1 (Mt. You have been sent by the Environmental...Ch. 4 - Fuel oils contain primarily organic compounds and...
Additional Science Textbook Solutions
Find more solutions based on key concepts
Suppose someone had used the false kinetics (i.e., wrong E, wrong n)? Would the catalyst weight be overdesigned...
Elements of Chemical Reaction Engineering (5th Edition) (Prentice Hall International Series in the Physical and Chemical Engineering Sciences)
Expand each of the following s-domain functions into partial fractions: a. Y(s)=6(s+1)s2(s+1) b. Y(s)=12(s+2)s(...
Process Dynamics and Control, 4e
Circumference and Area of a Circle) Heres a peek ahead. In this chapter, you learned about integers and the typ...
Java How to Program, Early Objects (11th Edition) (Deitel: How to Program)
Write SQL retrieval commands for each of the following queries: Display the course ID and course name for all c...
Modern Database Management
State whether each of the following is true or false. If false, explain why. All expression containing the | | ...
Java How To Program (Early Objects)
The speed of shallow water waves in the ocean (e.g., seismic sea waves or tsunamis) depends only on the still w...
Fox and McDonald's Introduction to Fluid Mechanics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.Similar questions
- Methanol (CH3OH) is produced in the reaction of carbon dioxide and hydrogen via the reaction and process given below: CO2+3H2→CH3OH+H2O The fresh feed to the process contains hydrogen, carbon dioxide, and 0.400 mol% inerts (I). The reactor effluent passes through a condenser that removes essentially all of the methanol and water formed and none of the reactants or inerts. The unreacted reactants and inerts are recycled to the reactor. To avoid buildup of the inerts in the system, a purge stream is withdrawn from the recycle. 100 mol/h of feed to the reactor (not the fresh feed to the process) contains 29.5 mol% CO2, 68.0 mol% H2, and 2.50 mol% inerts. The single-pass conversion of hydrogen is 46.71%. What is the recycle-to-fresh feed ratio?arrow_forward3. Suppose you are to measure the BOD removal rate for a primary wastewater treatment plant. You take 2 samples of raw sewage on its way into the plant and two samples of the effluent leaving the plant. Standard 5-day BOD tests are run on the four samples, with no seeding producing the following data: Sample Dilution Doi (mg/L) DOf (mg/L) Source 1 Raw 1:30 9.0 2.2 2 Raw 1:20 9.0 ? 3 Treated 1:15 8.5 1.5 4 Treated ? 9.0 1 a. Find the BOD5 for the raw and treated sewage, and the percent removal of BOD in the treatment plant. b. Find the DO that would be expected in sample 2 at the end of the test. c. What would be the maximum volume of treated sewage for sample 4 that could be put into the 300 mL BOD bottle and still have the DO after 5 days remain above zero?arrow_forwardA given soil sample is subjected for proximate analysis - specifically moisture content and analysis of inorganic matter (or ash) content. A cleaned and tared crucible is weighed in an analytical balance and found to be 4.5015 grams . The soil sample is weighed-in and the crucible, together with the plant sample, measured a total of 6.2525 grams. The set-up is then placed in an oven and dried to 105 degrees Celsius for at least two hours. The setup is cooled to room temperature in a dessicator and then measured to a constant weight of 5.9775 grams. Afterwards, the setup is placed inside the muffle furnace and ignited to 720 degrees Celsius for at least an hour. The set-up is cooled to room temperature again inside the dessicator and then measured to the constant weight of 4.9375 grams. (A) What is the percent moisture in the plant sample? Write the answer in THREE SIGNIFICANT FIGURES. (B) What is the percent volatile (organic) matter in the plant sample? Express answer in THREE…arrow_forward
- sunflower oil + 3methanol <--> 3 biodiesel product + glycerol A transesterification takes place by using sunflower oil and methanol and 1%wt. NaOH as catalyst. The ratio of sunflower oil to methanol is 1:6. 100g of sunflower oil will be used in this experiment. The result gives 60% glycerol yield. Calculate the mol and gr amount of the glycerol that is used according to these ratios: a) 1:6 b) 1:3 c)1:2arrow_forwardN2(g) + 3H2 (g) > 2NH3 Given the feed to the reactor consist of 100mol/s N2 and 250 mol/s H2. Calculate the percentage of excess of the reactionarrow_forwardThe oxidation of ethylene to produce ethylene oxide proceeds according to the equation2C 2H 4 +O 2 ! 2C 2H 4OThe feed to a reactor contains 100 kmol C 2H 4 and 100 kmol O 2. If the reaction proceeds to completion, how much of the excess reactant will be left; how much C 2H 4O will be formed; and what is the extent of reaction?arrow_forward
- Hematite is an iron ore with the following composition: Fe2O3 [MW=159.70]. To make steel, carbon [At. Wt. = 12.01] in the form of coke is used to reduce Fe2O3 to iron metal [At. Wt. = 55.85] as shown below: 3 C + 2 Fe2O3 → 3 CO2 + 4 Fe How many grams of carbon are needed to produce 2,500 grams of iron? Relative to the problem the processing of 798.5 g of hematite ore produced 508.2 g of iron metal. Determine the percent yield of pure iron for this batch?arrow_forwardA steady-state process to recover crystalline potassium chromate (K,CrOz) from an aqueous solution of this salt is required. Four thousand kilograms per hour of a solution that is one-third K,CrO, by mass is joined by a recycle stream containing 36.4% K2CrO7, and the combined stream is fed into an evaporator. The concentrated stream leaving the evaporator contains 49.4% K,CrO; this stream is fed into a crystallizer in which it is cooled (causing crystals of K,CrO, to come out of solution) and then filtered. The filter cake consists of K,CrO, crystals and a solution that contains 36.4% K,CrO, by mass; the crystals account for 95% of the total mass of the filter cake. The solution that passes through the filter, also 36.4% K,CrO,, is the recycle stream. 1- Draw the flowchart of the system and put all known information. 2- Calculate the rate of evaporation, the rate of production of crystalline K,CrO7, the feed rates that the evaporator and the crystallizer must be designed to handle, and…arrow_forwardFeed gas containing of 78.5mol % H₂, 21% of N₂ & 0.5% of Ar is mixed with recycle gas and enters a reactor where 15% N₂ is converted to NH3 as per the reaction. Ammonia from the exit of the reactor is completely separated from unconverted gases. To avoid the buildup of inerts, a small fraction (5%) of the unreacted gases purged and the balance recycled. USING ASPEN/HYSYS Draw the process flow sheet Product rate and Purge rate Basis:100mol/hrarrow_forward
- A brine solution of salt flows at a constant rate of 9 L/min into a large tank that initially held 100 L of brine solution in which was dissolved 0.4 kg of salt. The solution inside the tank is kept well stirred and flows out of the tank at the same rate. If the concentration of salt in the brine entering the tank is 0.04 kg/L, determine the mass of salt in the tank after t min. When will the concentration of salt in the tank reach 0.01 kg/L? Determine the mass of salt in the tank after t min, mass = | kgarrow_forwardTo prepare a delicious banana milk on an industrial scale, there is an experimental process that consists of seven unit operations. A stream of banana (whose components are fruit, peel, and moisture) is fed to a peeler, where 99.9% of the peel is removed. This stream should become pulp, so it is mixed with an additive Q to avoid pulp oxidation. This mixture is then sent to an extruder press wherein a stream of a 50:50 mixture of additives Q and R is added. The resulting flow of 30 kg/h has a composition of 2% additive R and 5% additive Q. This flow is then fed to an agitated mixer. To the same mixer is fed a dairy stream of 250 kg/h that contains 70% milk (the rest is water) and a sweet aqueous stream that contains 30% sugar. For each 25 kg/h of dairy flow, 2 kg/h of the sweet flow is fed. The stream that leaves the agitated mixer has 5% fruit and 0.005% peel and enters a series of two thermal processes in which each operation allows 5% of the water and 2% of the milk to evaporate. The…arrow_forwardButane (C4H10)(C4H10) and dry air are fed to a combustion reactor at a steady rate of 45.9 mol/s45.9 mol/s butane and 2500.0 mol/s2500.0 mol/s dry air. Assume the butane reacts completely to produce CO2CO2 and H2O.H2O. The reactants enter the reactor at 25 ∘C25 ∘C and the products leave the reactor at 1110.4 ∘C.1110.4 ∘C. Calculate the percent excess air. Using the information below, find the heat interaction. Species ΔHf at 298 K(kJ/mol) CP (kJ/kmol·K) O2 0 3.5R N2 0 3.5R C4H10 -125.5 12R CO2 -393.5 3.5R H2O -241.8 3.5Rarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning
ChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill Education
Principles of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill Education
Chemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781259911156
Author:Raymond Chang Dr., Jason Overby Professor
Publisher:McGraw-Hill Education
Principles of Instrumental Analysis
Chemistry
ISBN:9781305577213
Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher:Cengage Learning
Organic Chemistry
Chemistry
ISBN:9780078021558
Author:Janice Gorzynski Smith Dr.
Publisher:McGraw-Hill Education
Chemistry: Principles and Reactions
Chemistry
ISBN:9781305079373
Author:William L. Masterton, Cecile N. Hurley
Publisher:Cengage Learning
Elementary Principles of Chemical Processes, Bind...
Chemistry
ISBN:9781118431221
Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard
Publisher:WILEY
Mod-01 Lec-23 Degrees of freedom analysis; Author: nptelhrd;https://www.youtube.com/watch?v=c4h85JjrkzQ;License: Standard YouTube License, CC-BY
Introduction to Degrees of Freedom; Author: LearnChemE;https://www.youtube.com/watch?v=tW1ft4y5fQY;License: Standard Youtube License